AutoCad :: Crosshair Action After Selecting Command In 2012?
Sep 26, 2011
Back in Acad2002 when I selected a command (line, for example) the crosshairs would lose the pickbox around them and I could precisely pick the area I want with no obstruction. I see in 2012, that following those same steps, leaves the pickbox around the crosshairs and thus makes it obtrusive to precisely pick exactly what I want. Is there a system variable to make that pickbox disappear while I am making my selection?
View 4 Replies
ADVERTISEMENT
Dec 16, 2011
How can i change crosshair color in autocad 2012?
View 4 Replies
View Related
Sep 25, 2008
I am having a problem with a delay in selecting an object and selecting a command.
When I select an object the pointer has at least a 3 second delay before it starts moving around normally again. It is the same with selecting a command. This has started to get tedious. It has worked fine in the past so I don't think it is a RAM/graphics card problem.
View 5 Replies
View Related
May 14, 2013
I created two lines.
Before this problem appears, if I select one line then another line one-by-one, they are all selected.
But now, when I select one line then another line one-by-one, only last one is highlighted as selected (dashed line, two blue endpoints, and one blue middlepoint), the other one is not.
How do I switch back to the previous one?
View 5 Replies
View Related
Jul 8, 2011
I just upgraded from Autocad LT to Autocad 2012 (full version). When I go to select a hatch pattern by left clicking on it the program locks up. Then I have to "force-close" Autocad 2012 and loose some of my work.  It has done this in several diferent drawings. Autocad LT does not have this problem.Â
I have a HP Z workstation with 6 gigs of ram and an Intel I-5 processor (very fast machine) with a quadro fx 380 grahics card.
I tried reinstalling Autocad 2012 and that didn't work. Not sure what to do.Â
View 9 Replies
View Related
Jul 17, 2012
Since upgrading to AutoCAD Architecture 2013 I've noticed that the sequence in which I type my commands no long works. I used to be able to highlight various items and then type in the command I want to apply to these items - i.e. Mirror, Erase, Scale, etc. But now with 2013 I will select the items, then type in the command, and the it asks me to again select the items I wish to apply the command to. What settings I need to change in order to fix this?
View 1 Replies
View Related
Dec 20, 2013
My AutoCAD Map 2014 still allows me to select objects and then type the command to, for example, delete the items. I was able to do it in my Civil3d but it seems something was toggled so that I'm no longer able to. Now if I select items, once I select a command, it essentially unselects the objects or doesn't recognize that they are selected.
View 2 Replies
View Related
May 9, 2012
The key input that triggers the command that lets you select layout (.dwt?) files at the beginning before AutoCAD fully boots up?
View 2 Replies
View Related
Mar 8, 2013
I would like to automate an action set that selects a raster image (linked file) that has been grouped with vector art and then converts that selected raster image into a vector (live trace)
Â
I'm using cs5 on a mac. As far as format goes I have hundreds of eps files that all have at least one raster bitmap tif which was imported as a linked file and then grouped with vector art. So I will like to run a batch script command that will select only that bitmap raster image (because I want to maintain the present vector art in the file) and convert that bitmap tif to vector- and save the file which will hopfully be in vector format.
View 2 Replies
View Related
Dec 15, 2011
What happened to the dialog box for the array command in Map 3D 2012
View 2 Replies
View Related
Apr 9, 2013
Starting a few weeks ago Photoshop CS6 crashes every time when selecting the print command with the error : "Adobe Photoshop CS6 has stopped working" This happens using different printers and when printing anything, including a blank page. Printing works fine from other applications.
Running Photoshop CS6 v.13.1.2 x32 on Windows 7 Professional 64bit
This is a Dell Optiplex 990, I7 3.4GHz, 4GB RAM, 250GB HDD system, AMD ATI RADEON HD 6350 PCIe Video Card on a 16x bus
Â
1) Photoshop has been updated
2) OS has been updated
3) Video drivers have been updated with new ones from the manufacturer
4) I tried new drivers for our Kyocera TaskAlfa 3550ci
5) I tried new drivers for our Kyocera FS-3140MFP
6) I also tried removing all of the printers except "Adobe PDF" printer
Here is an example event from the Windows Application Log after photoshop crashed.
Faulting application name: Photoshop.exe, version: 13.1.2.0, time stamp: 0x50e86403
Faulting module name: ntdll.dll, version: 6.1.7601.17725, time stamp: 0x4ec49b60
Exception code: 0xc0000374
Fault offset: 0x000c380b
Faulting process id: 0xa0c
Faulting application start time: 0x01ce355706f614ca
Faulting application path: C:Program FilesAdobeAdobe Photoshop CS6Photoshop.exe
[code]....
View 9 Replies
View Related
Jan 17, 2012
Where is the command delete duplicate objects in AC2012? In version 2011 it was in express tools. Whether this command is not in version 2012?
View 2 Replies
View Related
Jun 6, 2011
Whenever I place a copy or paste from the clipboard AutoCAD freezes for about 5 -8 seconds and is very annoying. Time is money people.  I know it's not a RAM issue. I don't have the problem with 2011 when I go back to it. What gives Autodesk? When is the next service pack due? This only happens with teh copy command
View 9 Replies
View Related
Sep 19, 2011
Why Autocad 2011 and Autocad 2012,Will occur on some computers,Can use the "_.layer" be executed,Some do not?Because on the Autocad 2006 can be executed.
View 1 Replies
View Related
Apr 26, 2012
Since last week (4-19-2012) Our users have been expierencing cursor issues and freezes with Civil 3d 2012. Entering commands in the command line very slugish, pressing the shift key to select / de-select, trim, open osnap menu, ext.
We are running Win7pro6d bit quad core machines with 6gb ram, ATI FirePro V4800 (FireGL), Intel Xeon ES640 (2.67 ghz). AutoCAD Civil 3D(SP2) and all hotfixes installed.
This problem just started one week ago and It started with the cursor jumping all over the place when crossing objects. However; we now have very sluggish command line entry, 2 - 3 seconds after typing till it shows up, and cursors freezing when pressing the shift key for any reason.
View 5 Replies
View Related
Mar 9, 2012
I have a problem where autocad will hang for almost 1 minute if I type in a misspelled command shortcut or misspelled command. For example if I try to type in "line" and I type in "linr" it will hang up for around 50 seconds. Is there a setting, system variable or key in the registry to stop autocad from looking for a command/shortcut that doesn't exist?
View 6 Replies
View Related
Feb 8, 2013
Is there a way to get into a 2012 Action setup via history in 2013?
View 3 Replies
View Related
Feb 1, 2012
Im using MEP and in MEP2010 the Offset command worked fine on my structural members, offsetting to the direction I picked.
In MEP2012 the offset command now offsets the same structural member to the opposite side of the point I pick.
The structural member is rolled 180 and the way I can correct this offset issue is to roll the SM back to 0, then the offset command offsets to the correct side.
Is there a new setting or something in 2012 that will get the offset command behaving the way it did in 2010 where it does not care about the objects properties and just offsets it correctly?
View 9 Replies
View Related
Jun 13, 2013
I have a question about using Find and Replace in an Action. For a bar chart with negative values, Illustrator will generate the value on the axis using a hyphen (e.g., -1, -2, -3). I would like to change the hyphens to en dashes (–1, –2, –3).
Â
I have 150 graphs, so the easiest way to do this would be to use an batch action on all graphs in a folder. I first flatten the graph and then do a find-and-replace..The trouble is that I get prompted at each find and replace..Of course I can click Find, Replace All, OK, Done each time, but this essentially defeats the purpose of creating an action.
Â
Is it possible to suppress the Find and Replace window and set the action to Replace All without prompting?
View 4 Replies
View Related
Oct 9, 2012
I need to do a form of automation, but wanting to execute this from another process (self-made application). Adobe Photoshop has this mechanism called "Droplets" that are executable based upon Actions defined in Photoshop (as far as I can understand). Is it possible to let AI do some work for you from an external application as with Photoshop (assuming you are able to execute the executable once it has been created)?
View 4 Replies
View Related
Jul 2, 2013
The options window will not display when typing "options" in the command line or selecting from the drop down. The options menu has to be hidden somewhere because AutoCad will not allow any other commands after typing options until I hit escape. I have tried restarting CAD and rebooting my computer with not luck.
View 9 Replies
View Related
Jan 15, 2013
I am running Inventor 2012 sp2.
Even with a simple IPT that only has a handfull of features, at times it takes a long time (3-5 minutes, sometimes longer) for Inventor to execute a undo or redo command.
Undo file size setting in Application options is set at 1MB (which is teh same setting I used in previous versions).
View 9 Replies
View Related
Feb 18, 2013
I have an action which applies Levels and Curves to my black and white TIFFs. At the end it "saves as" a JPEG. Originally it saved them at quality level 10 but I re-recorded the action to set the quality at 12. However, since this change the action keeps saving as into the folder where the image I used for the re-recording was located.
View 1 Replies
View Related
May 26, 2011
I have been annoyed with the color of my crosshair for a while, I have my background set to black so the the crosshair is white. This is no problem in Model and over the paper in Layout, but when I move the crosshair outside the paper to the Grey area, I can't see the crosshair.
I can't remember this being a problem before so it must be something with 2011 that I installed a while back.
I can find where I change the color of the crosshair (Options > Display > Colors > Crosshair) so thats not the trouble.
The trouble is that since I can't remember this being a trouble before, the crosshair must have changed color from White when black background to Black when white background.
And I seem to remember that there was a color before that was called Black/White that was this exactly. It changed from Black to White depending on the background .
View 9 Replies
View Related
Sep 30, 2011
How does one get the array window in 2012 to open with the array command like it does in 2007
View 2 Replies
View Related
May 24, 2011
i cannot get the tools name while dragging the cross hair towards the tools it is displaying only some boxes .
View 3 Replies
View Related
Nov 8, 2012
How to rotate the X Axis in the Crosshair? See picture attached.
View 3 Replies
View Related
Nov 24, 2010
Is there a way to make the cross hairs default to the inverse of the color under them (e.g. black when over white, blue when over yellow, cyan when over red, etc.)? I remember that it did this in previous versions, but I can't find a setting for it in 2011.
View 9 Replies
View Related
Feb 22, 2012
my crosshair displays the trails all the time. What can I do to resolve this problem; it's not the mouse setting.
View 2 Replies
View Related
Sep 21, 2010
when i started using 2011. I have 2 viewports active; plan and isometric view. But when I try to navigate in the isometric view, the crosshair behaves in a way I don't understand. What happens is that when I zoom in the crosshair disappears over or under what I'm zooming in on.
It's hard to describe, but it seems that it have a different origo then the view represents. When I zoom out so much that the crosshairs are visible and I try to move them upwards, they stop in the middle of the screen and then the marker becomes visible in the ribbon part of the screen.
I have tried detaching all xref's, purged and audit, checked the elevation (0). This only happens in some drawings, not all, and I can't think of a common denominator in the drawings it happens.
View 8 Replies
View Related
Jul 6, 2013
I've created an action that uses the save for web dialogue to optimise images for the web. When I use the batch command to process a full folder of images, even though I have "Override action "save as" command" checked, it ignores this and still uses the location that was used when the action was created.
Â
Apparently this is a known issue in CS6 and previous versions but whether this has been fixed in Photoshop CC?
View 7 Replies
View Related
