I need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
View 5 Repliesi've made a serpantine curve that starts from one line of alignment and end on the other line.
i wanted to know how can c change alignment direction when these two feature line and alignment meet each other in order to change the alignment path?
I would like to add elevation values of start and end of feature line segments within a table. I can set up start and end co-ords but can't seem to find where I can add the levels?
I can add lables to the plan with levels but really would like to have a table as well as some of the segments are too small to lable on the layout.
I need to start a Feature Line at a point on another Feature Line 0.100m below the beginning of the existing Feature Line.
View 2 Replies View RelatedI've seen a label style somewhere that can label the elevation of vertices and elevation points on feature lines. How to style or a procedure for creating a style for this?
I've found a couple of blogs that layout the steps for a style but it seems there are a few ways to do it so I'm looking for what could be considered the most effective/versatile approach.
Is there a way to convert a feature line elevation point to PI?
My objective here is to delete all the elevation points except one. It would be time consuming to pick each elevation point and delete them individually (in this case there are about 15 but sometimes there are more). I want to use the delete all option but keep one one of them. If I can convert that one into a PI I could then quickly delete the remaining elevation points.
The way I used to adjust feature lines was to highlight the node I wanted to adjust and then raise or lower that elevation incrementally until I got to a grade that worked.
Now I've noticed that when I highlight a node and hit the button to raise or lower, it forgets which node I had highlighted after the first press. This is a problem because now I either have to click on the node every time, because if I don't it will raise or lower the elevation of the entire feature line.
Is there any way to increase the size of the marker that shows up on the plan view when you select a PI in the elevation editor? It is so small that if I have the feature line selected I can't see the marker over the highlighted line. I generally have to zoom to a PI so I can see where I am.
View 6 Replies View RelatedC3D 2012
I want to set and Elevation Point (not a PI Point) along a feature line by entering the grade from the previous point. Currently the "Set Elevation Point" command only allows entering an elevations or getting an elevation from the surface. I know I can set an elevation point and then use the "quick elevation editor" to adjust the grade, but I don't want to go through the extra step.
C3D 2013, Win 7, 64 bit
When I try to create a feature line using an alignment/ profile, sometimes it gives me a feature line for the entire alignment, even though my profile is only a small segment. I made sure I selected the correct profile, and I even deleted all other surface profiles just in case. But it still gives me a wonky feature line for the entire alignment.
However, in the same file, other profiles have worked perfectly.
Is there a way to add elevation labels at any position on a feature line without having to create a surface?
View 9 Replies View RelatedWindows 7, 64 bit, Civil 3D 2010
I'm trying to create a surface using feature lines. I have an alignment and profile that I have created a dynamic feature line. However, on a horizontal curve, it apparently creates a vertex at the start and beginning of the curve, and nothing on the curve, so it triangulates between those two points and that's it.
Do I need to play with spiral tessellation (0.25), mid-ordinate distance (0.1) to get some points along the curve?
Inserted an alignment line table. It's in model space and viewported (locked) to the layout. On the screen it looks fine but during print preview and printing it comes out too small. Can this be controlled?
View 8 Replies View RelatedI need a label style that not only labels the major stationing of an alignment, but also displays the corridor surface elevation beneath it.
10+000
|
22.10m
Something similar to above.
I can add reference text for surface elevation to the alignment label, but all I get is the ???, no surface value.
What am I missing?
I need to know how to display a proposed profile elevation in the major station alignment label, I mean, for example, I want to read in the label "0+000, 494.444". I've already edited my major station label style adding a (profile type) Reference text, and it only displays "?". I suppose I need to associate it with the correct profile, but I've not figured out how to. I show you how the label looks in the attached image.
View 8 Replies View RelatedUsing Civil 3D 2012 SP 1 on Win7 Pro 64-bit.
Is there any reason why a corridor model would not be respecting the manually entered super elevation values in the alignment? I have several stations that should be calculated with even super elevation values, but they aren't. For example, at station 0+080 on my alignment the left crown should be running at -3%, but it is actually being calculated at -2.47%. It isn't just one station; it's most of them. No overridden stations, vertical targets, etc in the corridor. Just a fairly straight-forward align (hor/vert) with super, simple assembly (two lanes, shoulder, daylight), simple corridor.
Is there a way to show the MES Top Elevation as blank or a dash? It would be great if I could make an expression but without the use of text strings in the expression editor, I don't know how to accomplish this without using wipe out boxes over the elevations.
View 2 Replies View RelatedI am create the stron network. I want structure profile elevation. How to create expression in structure reference alignment profile elevation.
View 9 Replies View RelatedI want to be able to make a alignment table with northing and easting coordinates for the following:
bop
pi's
eop
Is this possible? The closest I get is to make a curve table with the pi coordinates and no bop or eop coord'.
Civil 3D 2014
Win 7
It is possible to create a table for an alignment as shown in the example attached?
View 1 Replies View RelatedHow to get the Volume Elevation Table masking to work?
I can only get the Title to work correctly - everything else plots as a black blob if Fill is on. With Fill off - there is no mask.
I'm trying to add an alignment table, but the curves seem to be labelled twice. When I first labelled the alignment, the curves were C???, so I tried again. After a lot of messing around, I finally got C1, C2, etc., but the table lists C1 & then C?. I've thawed & turned on all the layers, but there aren't any C??? labels on the alignment. Another alignment in the same drawing worked fine.
View 4 Replies View RelatedIf there was any way to get deflection angles of an alignment into a table? I finally figured out how to get C3D to label them using the add note label. If this is not possible, is there a way to make a table of the notes? I am using C3D 2013 version if it makes any difference.
View 4 Replies View RelatedIs there a way to add a column that would show for each elevation range the percentage of the total area?
View 1 Replies View RelatedSo we have to adjust the elevation of hundreds of drainage structures from their existing elevation to the new finished ground elevation.I know we can give this information within the structure label by adding a reference surface but we would like to produce a table with three columns:
Structure No. Existing Rim Elev. Proposed Rim Elev.
How to produce such a table?
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
I need to produce a better standard table for our company, but need to know how it would be possible to display only either the START STAKE VALUE/ STATION or END STAKE VALUE/STATION in the appropriate column. If I can achieve this i would not need to details for straight segments as indicated in the details column.
View 5 Replies View RelatedI have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.
To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.
I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?
I want to create a Curve table for an alignment.
You are able you get range of properties, i.e length, chord length, start/end chainages, mid-ordinate.
I've notice lets for arguement sake 'chord length' text component editor is: <[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]> but is it possible to modify the code so i can insert half a chord length.
Ive tried
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]>/2 ---- doesn't work
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]/2> ---- doesn't work
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)/2]> ---- doesn't work
<[1/2*Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]> ---- doesn't work
I have created an easement after I selected the line callouts and created my parcel table I realized I missed selecting one of my line labels and it is missing from my table. I know I can just erase the table and then reselect all line callouts to create a NEW table, but I was wondering if there was a way to just select the line callout I missed and have it added to the parcel table without recreating a new one.
View 3 Replies View RelatedIs there a way to create a table of stations and offsets along a specific alignment at chosen locations?
Dynamic would be preferred.
I'm currently using version 2013.
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013