Is there any way to increase the size of the marker that shows up on the plan view when you select a PI in the elevation editor? It is so small that if I have the feature line selected I can't see the marker over the highlighted line. I generally have to zoom to a PI so I can see where I am.
View 6 RepliesI want to navigate along my feature line, viewing which point is screen is the current point at the grid.
My feature line shows its points with blue circle & square grips and the current point is showed by a green circle.
The problem is the zoom level, Grips have always the same size but circular green indicator does not.
You can only view this last at a very detailed zoom.
I'd like to have a "big" arrow or something similar.The problem is the great difficulty to identify points....
Civil 3D (2013)
The way I used to adjust feature lines was to highlight the node I wanted to adjust and then raise or lower that elevation incrementally until I got to a grade that worked.
Now I've noticed that when I highlight a node and hit the button to raise or lower, it forgets which node I had highlighted after the first press. This is a problem because now I either have to click on the node every time, because if I don't it will raise or lower the elevation of the entire feature line.
Is there a way to convert a feature line elevation point to PI?
My objective here is to delete all the elevation points except one. It would be time consuming to pick each elevation point and delete them individually (in this case there are about 15 but sometimes there are more). I want to use the delete all option but keep one one of them. If I can convert that one into a PI I could then quickly delete the remaining elevation points.
C3D 2012
I want to set and Elevation Point (not a PI Point) along a feature line by entering the grade from the previous point. Currently the "Set Elevation Point" command only allows entering an elevations or getting an elevation from the surface. I know I can set an elevation point and then use the "quick elevation editor" to adjust the grade, but I don't want to go through the extra step.
I need to start a Feature Line at a point on another Feature Line 0.100m below the beginning of the existing Feature Line.
View 2 Replies View RelatedI've seen a label style somewhere that can label the elevation of vertices and elevation points on feature lines. How to style or a procedure for creating a style for this?
I've found a couple of blogs that layout the steps for a style but it seems there are a few ways to do it so I'm looking for what could be considered the most effective/versatile approach.
I need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
View 5 Replies View RelatedIs there a way to add elevation labels at any position on a feature line without having to create a surface?
View 9 Replies View RelatedI think this issue started with SP2. I don't remember having these issues in SP1 and earlier.
Create some COGO points at varying elevations.Start a new feature line.Use "node" object snap and pick your first cogo pointIt does not pick up the elevation of the point (it used to)Now draw feature line segments to a few more cogo points entering the elevation each time.It does not pick up the elevation of the point (it used to)Now switch to Arc mode and snap to a few more cogo points.It does correctly picks up the elevation of the cogo points (like it used to)R.K. McSwain | CADpanacea | twitter | Cadalyst tips/code
When I snap a point to an object, the point takes on the elevation of the object. I would rather the point's elevation stay as is.
-changing osnapz variable
-latest civil 3d service pack
A few weeks ago I did not have this problem but once my computer was switched to the company's global server and c3d was reinstalled the problem appeared. Furthermore (post switchover), when a colleage of mine prepared a simple test drawing with just a line and a point, he was able to snap to that line without the point changing elevation. When he sent that drawing to me and I tried snapping the point to the object, the same problem occured with the point taking the elevation of the line object. I suspect it is a system variable issue
I read all of the posts I could on point gaps and know how to make the leader reach for the center of the point. What I want is for the leader to actually attach to the block of the style I have created. Is this possible, or do I need to find a new way to label of these points so that the leader touches the block. Also I noticed the gap is not consistent from point to point.
I am using civil 3d 2011 with the latest service pack.
Civil 3D 2013
HP Z400 Workstation
6GB of RAM
296GB HDD
ATI FirePro V5700(FireGL)
Win 7 Home Professional
I have my layer set up as dashed linetype for lines. My point style marker is set up as continuous linetype. When I import the survey file it automatically draws the lines correctly, inserts the correct marker, and places them on the correct layer. But the marker is dashed as well and not continuous. Is something overriding this setting?
View 2 Replies View RelatedHow do you get a point marker that uses a block with attributes to show the attributed text?
We are using tree symbols that have the size of the tree as an attribute, but when the points that use that block come in...the block shows up w/out any attributed text. Tried to edit the "block" or point marker with attedit command, but C3D tells me it is not a block. Understand that it is a "marker" for the point. But, what is stopping the text size of tree from showing up?
In previous versions of Civil 3D there was a grip on the point marker that allowed me to rotate the block used as a point marker, where did this grip go in 2013? How can I rotate an individual point marker without having to create a separate point style?
View 1 Replies View RelatedEssentially, what I am looking for is the easiest way to label control lines and right-of-way lines in section view. In the past, I have used profile grade lines to do this - with a customized Marker Style for each alignment. On projects with 40+ alignments, this leads to a lot of blocks and marker styles to wade through. What I'd like to know - Is there a way to display a point name (read from a MarkedPoint) in section view using marker labels? Here's how I see it working (theoretically):
Define the following two point codes for use in my Code Set Styles: ALGN and ROW. Each would be assigned a Marker Label Style (let's call them A & R) in the Code Set. I'd like this label to display the point name in section view. For example, I'd like to insert a marked point on the centre line; Point Code = ALGN, Point Name = L100. However it doesn't seem that the Marker Label can read the "Point Name" field. Am I missing something really simple, or is this just not doable?
Is there a reason why the "node" osnap won't recognoze certain point markers? I have recently begun using named plot styles and I have been revising some of our markers to reflect this. I have noticed that some of the point markers (it seems like markers that use a circle as part of the marker) won't show the node marker no matter how I hover around it. Others seem to be normal.
View 7 Replies View RelatedI would like to add elevation values of start and end of feature line segments within a table. I can set up start and end co-ords but can't seem to find where I can add the levels?
I can add lables to the plan with levels but really would like to have a table as well as some of the segments are too small to lable on the layout.
How do I turn off the elevation grid in the section editor when looking at the cross-sections of my corridor?
View 1 Replies View RelatedI needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
Is there a way to change all your point styles display mode (flatten to elevation, use point elevation, or exaggerate elevation) at once? I don't mean make a new style and then apply it to all points: I want to systematically change it for all my current point styles.
View 5 Replies View RelatedIs there anyway to create a point from the coordinate and elevation data listed in a section inquiry panel (see attached)?
View 3 Replies View RelatedI'm looking to change an elevation of a survey point within a drawing. I can see where it is possible to manually unlock the points from the Survey Database to allow the user to edit the point. I'm not seeing a method or property in the API Help for 2013 to do the unlocking with code.
Also is it possible to convert a Survey Point to a regular Cogo Point through the code? Or do I have to delte the point and then recreate it as a COGO point? I think this will be my work around if the above doesn't work.
I'm trying to determine if it's possible to take a 09 LDD Companion drawing in which the elevations for many points have been moved AND/OR rotated (to align with roadway), and not only convert these to C3D, but also have them transferred along with the move/rotate information. We're talking about a mile long stretch of roadway and the project is 6 years old (i.e. no C3D when it was originally done).
The problem is that there are a ton of ground shots that need only be shown to 0.1 precision but are shown to 0.01 precision. LDD was not able to assign an elevation precision to groups of points, only all cogo points together, which meant we had to explode certain groups of "soft shot" points once they had been inserted at the desired precision.
If there's no way to do what I'm asking, it's no big deal for this case since the higher precision can be easily rounded to the lower by the viewer (better than the other way around). But as I am the only one on C3D and have been for the past 2 and a half years, we will likely face this monster again several times over with other drafters' projects and I'd like to have a best practice in place if we need to go the other way (extracting 0.01 precision from 0.1 precision).
Civil 3D 2012
Windows 7 Enterprise SP1
Dell Precision T3400
(Q9550 @ 2.83 GHz)
8GB RAM
Nvidia Quadro GTX 650 Ti BOOST
How can I get the channel subassembly to attach to the assembly insertion point at the channel flowline marker? I need the flowline to follow my profile elevations.
View 4 Replies View RelatedHow I would replace the Elevation label on a point with Alphanumeric text on certain points in a point group (or if it can be done at all)
Some background info:
I work with site diagrams that have monitoring wells and each one has a groundwater elevation value that gets updated every year according to field data. Our current setup is that the monitor well name and elevation values are displayed using point labels and looks like:
x 12-1 (Monitoring well name)
788.432 (Groundwater elevation value)
However, sometimes the monitoring well is dry and we need to display 'DRY' instead of a numeric elevation value. Autocad won't let me put 'DRY' as an elevation because it's not a number. Is there a way to override this, or somehow make the label display 'DRY' if elevation of 0 is entered?
Another use to overriding point label elevation is that sometimes the groundwater elevation that we get from the monitoring well is so far off from the general contour pattern that we will put the elevation value of that well in brackets such as (788.432) and indicate that this means the elevation was not included in the groundwater contour flow map.
Is there a way to do this override, or is there another method I should be using to label my monitoring well elevations? I know I could just MTEXT everything, but that's double the time to update the point elevations for the contours and then updating the mtext to display the numerical elevation values.
Is it possible to rotate the point labels when working with point files from an elevation Survey in Ciivil 3D? When activating the labels visibility they are horizontal, but when I rotate the drawing to a side view I am can´t see them.
So far I was working with Autocad (importing a dxf). Is there a way to rotate at the same time all the points labels, wich in this case are just text items?
How do I drop trailing zeros for numbers that end in zero, but keep a 0.1 precision for all other numbers in a point label style?
ie. I want to have points display 702 and 708.5 in the same point label style.
I am modifying an elevation of a point and this throws me the error Fatal Error: Unhandled Access Violation Reading 0x0018 exception at c74f11ech
View 1 Replies View RelatedI have a bunch (hundreds, so manual input not an option) of X,Y points without elevation data that I would like to import into a DWG and assign an elevation that is based on an existing surface object. Is there a way to do this for a point file? The command for inserting individual points would be the "Create points - Surface > Random" but I don't see a way to do this in a batch type method where i have my PNE formatted input file to just move the points to sit on the existing surface.
View 2 Replies View RelatedI see that the Point Cloud Feature Extraction is now part of the Productivity Tools for Civil 3d 2012. Are these tools available in 2013? I am not seeing them anywhere. It seems goofy that there would be more tools available for the old release - what's the incentive to make the switch? Would you expect they will be available for 2013 sometime soon? I'm not complaining, I really like 2012
View 4 Replies View Related