I've seen a label style somewhere that can label the elevation of vertices and elevation points on feature lines. How to style or a procedure for creating a style for this?
I've found a couple of blogs that layout the steps for a style but it seems there are a few ways to do it so I'm looking for what could be considered the most effective/versatile approach.
how I can add in some vertex's at regular intervals on a fline or pline?
C3D 2013
I need to start a Feature Line at a point on another Feature Line 0.100m below the beginning of the existing Feature Line.
View 2 Replies View RelatedIs there a way to convert a feature line elevation point to PI?
My objective here is to delete all the elevation points except one. It would be time consuming to pick each elevation point and delete them individually (in this case there are about 15 but sometimes there are more). I want to use the delete all option but keep one one of them. If I can convert that one into a PI I could then quickly delete the remaining elevation points.
The way I used to adjust feature lines was to highlight the node I wanted to adjust and then raise or lower that elevation incrementally until I got to a grade that worked.
Now I've noticed that when I highlight a node and hit the button to raise or lower, it forgets which node I had highlighted after the first press. This is a problem because now I either have to click on the node every time, because if I don't it will raise or lower the elevation of the entire feature line.
I need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
View 5 Replies View RelatedI am wanting to add the name of my feature line to a label style. I am trying to create a label style that will show Lot Number and Area. I know i can create parcels, but i dont want to! I have also created a map table that can do exactly what i want on polylines, but will not work on an xref. Labelling featurelines does work in xrefs.
how to add the name into a label style?
Is there any way to increase the size of the marker that shows up on the plan view when you select a PI in the elevation editor? It is so small that if I have the feature line selected I can't see the marker over the highlighted line. I generally have to zoom to a PI so I can see where I am.
View 6 Replies View RelatedC3D 2012
I want to set and Elevation Point (not a PI Point) along a feature line by entering the grade from the previous point. Currently the "Set Elevation Point" command only allows entering an elevations or getting an elevation from the surface. I know I can set an elevation point and then use the "quick elevation editor" to adjust the grade, but I don't want to go through the extra step.
I have a plan I want to create a table of feature line (the ones used as ditch cl's) with the designation (ie R1), the overall length (this part I can do) and then the Delta z of the entire feature line. I can get segment Delta z, but not the entire Delta z.
View 4 Replies View RelatedIs there a way to add elevation labels at any position on a feature line without having to create a surface?
View 9 Replies View RelatedI am trying to create an elevation label that will give me the spot elevation followed by the letters "TC" and then on the line below subtract 4 inches from the elevation followed by the letters "BC". It's easy enogh to add the letters but the simple equation of elevation - 4 inches eludes me.
View 3 Replies View RelatedHow to create a flow arrow label for a feature line that parallels the curve?
I've a vague notion that this could be done with a dynamic block and a few fancy expressions. I'm comfortable with expressions, but I've never used dynamic blocks at all, so I wouldn't know where to start.
To be clear, I know curved text is possible, but I'm looking for a curved line (ie an arc) that would look 'parallel' to the arc of the feature line (ie have the same centre point). This would have to be dynamic to allow for different radii and for flipping to the left and right side of the feature line.
Any way to label the elevation of an object where it is picked? For example, I'd like to be able to pick on the node of a feature line or 3D polyline (or any object really) and have a label placed that displays the elevation of the object at the point where it was picked. This could appear similar to the surface spot elevation label, but instead of getting it's elevation from a surface, it would come from the object where picked.
Alternatively, any way to create a label style, perhaps using the Note label, to display something like this? I don't even care if it is dynamic or not, static would be fine. However, I do need it to scale innovatively . Tool Pac has a feature that does this, but the label is just a polyline and text that is not annotative.
How do you label a polyline with a Z elevation that is not part of a surface? want to label the contours, but they are not part of a surface.
2013 Civil 3D.
I would like to add elevation values of start and end of feature line segments within a table. I can set up start and end co-ords but can't seem to find where I can add the levels?
I can add lables to the plan with levels but really would like to have a table as well as some of the segments are too small to lable on the layout.
C3D 2013. We have profile line labels, some of which get manually edited (for example, change the "<[Tangent grade(FP|P2|RN|AP|GC|UN|SD|OF)]>" to a static number such as 0.29%).
However, if you CTRL+Click and select one of these labels and change the style of that one label, then the manual edits are lost and the label reverts back to the default string.
Is there any way to turn this behavior off?
I need a label style that not only labels the major stationing of an alignment, but also displays the corridor surface elevation beneath it.
10+000
|
22.10m
Something similar to above.
I can add reference text for surface elevation to the alignment label, but all I get is the ???, no surface value.
What am I missing?
Is there a way to label or list a station at a specific elevation? I know how to list and label an elevation at a given station but I need to know where a specific (given) elevation is located on an alignment or profile. I don't care if this is listed or labeled on the alignment or profile, I just need to be able to get a station at a given elevation.
View 5 Replies View RelatedI need to know how to display a proposed profile elevation in the major station alignment label, I mean, for example, I want to read in the label "0+000, 494.444". I've already edited my major station label style adding a (profile type) Reference text, and it only displays "?". I suppose I need to associate it with the correct profile, but I've not figured out how to. I show you how the label looks in the attached image.
View 8 Replies View RelatedI have a sheet with labels on the TBC with station and elevation. If I plot the sheet everything shows up fine. If I publish to PDF, the elevation portion of the labels shows as ?
View 1 Replies View RelatedHow do I get Civil 3D to put pipe elevation labels at even stations?
View 1 Replies View RelatedI have been searching for a way to rotate surface spot elevation labels but have not been able to find a solution to do so. Has this feature been added to 2013 or 14? I do not want to use the point and label styles for my surface elevation, even though these can be rotated. I have several miles of roadway with many horizontal curves and would like the surface labels aligned with and along the centerline. I prefer not to update the spot elevations when the profile is revised.
C3D 2013 (latest updates), 2014 Infrastructure Design Suite
Win 7 Pro, 64-bit
16 GB RAM
How I would replace the Elevation label on a point with Alphanumeric text on certain points in a point group (or if it can be done at all)
Some background info:
I work with site diagrams that have monitoring wells and each one has a groundwater elevation value that gets updated every year according to field data. Our current setup is that the monitor well name and elevation values are displayed using point labels and looks like:
x 12-1 (Monitoring well name)
788.432 (Groundwater elevation value)
However, sometimes the monitoring well is dry and we need to display 'DRY' instead of a numeric elevation value. Autocad won't let me put 'DRY' as an elevation because it's not a number. Is there a way to override this, or somehow make the label display 'DRY' if elevation of 0 is entered?
Another use to overriding point label elevation is that sometimes the groundwater elevation that we get from the monitoring well is so far off from the general contour pattern that we will put the elevation value of that well in brackets such as (788.432) and indicate that this means the elevation was not included in the groundwater contour flow map.
Is there a way to do this override, or is there another method I should be using to label my monitoring well elevations? I know I could just MTEXT everything, but that's double the time to update the point elevations for the contours and then updating the mtext to display the numerical elevation values.
I would like to know if it is possible to display the pipe inlet/outlet elevation in my structure label. It seems like it is not possible.It is possible to use the inlet/outlet elevation of the pipe in my pipe label however I would like to display it in my structure.
View 2 Replies View RelatedI know that I can add coordinates for such elevation using text component editor but I have to add the letter "N" for North or "E" for East to identify the location of the elevation (North/East/South/West). But, is there a way to make a label style that reads up the location of an elevation automatically?
I've attached pictures below for this issue.
C3D 2012, C3D 2013
Windows 7 Professional 64-bit
Intel(R) Core(TM) i5-2500 CPU @ 3.30GHz
How do I drop trailing zeros for numbers that end in zero, but keep a 0.1 precision for all other numbers in a point label style?
ie. I want to have points display 702 and 708.5 in the same point label style.
The defaul label style for the Elevation of points is set to 3 decimal places. We are trying to change the elevation display to 2 decimal places. We have tried the directions in the following discussion: [URL].......
Which is:
Toolspace
->Settings
-->Drawing name
--->Edit Drawing Settings
---->Ambient Settings
----->Elevation
------>Precision -> We modify from 3 to 2 decimal places.
It does not modify the display settings.
Also:
Toolspace
->Settings
-->Drawing
--->Point
---->Label Styles
----->(right-click) Edit label styles
------>Layout
------->Text
-------->Contents
--------->click on the "..." (three points) button
(Open "Text Component Editor - Contents"
--------->Select Point Elevation in the driop down list.
---------->Precision: Set to 0.01
------------>Ok, Apply, etc...
This does not seem to work either.
I want to create new vertex points in feature line and 3dpol.
I have this:
try
{
if (obj.GetType() == typeof(Autodesk.AutoCAD.DatabaseServices.Polyline3d)) {
Polyline3d p3d = (Polyline3d)trans.GetObject(entRes.ObjectId, OpenMode.ForWrite);
[Code]....
In this code line:
oFtrLn.InsertFeaturePoint(punt, AeccLandFeatureLinePointType.aeccLandFeatureLinePointPI);
always catches the same Exception "the value is not within the expected range" .I have translated it because I get "El valor no está dentro del intervalo esperado". Perhaps is this: " Value does not fall within the expected range.".
I have tried it with different point3d values but always catches Exception.
With pol3d I have similar problem.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
I’ve had this problem with my proposed elevations for quite some time so I finally want to fix it while I’m a little slow. The problem I have is when I change scales, my elevation’s (in dragged state) leader vertex does not connect to my line. I’ve attached my lable styles...
View 7 Replies View RelatedI needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?