AutoCAD Civil 3D :: Profile Elevation In Alignment Label
Sep 25, 2012
I need to know how to display a proposed profile elevation in the major station alignment label, I mean, for example, I want to read in the label "0+000, 494.444". I've already edited my major station label style adding a (profile type) Reference text, and it only displays "?". I suppose I need to associate it with the correct profile, but I've not figured out how to. I show you how the label looks in the attached image.
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
and I have tried it using {Station Value} instead of {Raw Station}
Here's what it's meant to do (because it's a long one):
If the station value + 5 is not divisible by 15, return -1 If the station value + 5 is divisible by 15, return the profile elevation, if the profile elevation is in the 100 range, subtract 100 if the profile elevation is in the 200 range, subtract 200...etc
Here is my conundrum: If I use the expression in a profile label, it works fine. But if I use it in an alignment label as reference text, it returns -1 for every value.
I am trying to create an elevation label that will give me the spot elevation followed by the letters "TC" and then on the line below subtract 4 inches from the elevation followed by the letters "BC". It's easy enogh to add the letters but the simple equation of elevation - 4 inches eludes me.
Using Civil 3d2012, Is it possible to change the alignment label style set after the alignment has been created? For example, for an alignment that was created with alignment label set X - change the label set to alignment label set Y? It seems like this should be pretty easy, I must be missing something obvious.
differences in elevations of points along Profile 2 (the proposed new road elevation) and Profile 1 (the existing elevation/surface) should be computed and shown right above the Profile 2 line. For example, if at a certain point PT 1 the elevation of the proposed road is 132.44 meters and the elevation of the existing surface is 132.45 meters, the difference is -0.01 meters and it should be shown exactly above the Profile 2 line (or a little bit above it) but not on it. The same should be done for every chosen point along the proposed profile.
So far, I have done this manually, by dragging the difference (already automatically computed and shown in one of the bands below the profiles) to the correct place for every single point. However, I don't know how to do this automatically.
C3D 2013. We have profile line labels, some of which get manually edited (for example, change the "<[Tangent grade(FP|P2|RN|AP|GC|UN|SD|OF)]>" to a static number such as 0.29%).
However, if you CTRL+Click and select one of these labels and change the style of that one label, then the manual edits are lost and the label reverts back to the default string.
I'm trying to label my Profile label stations as raw stations, 20~20 meters, and I'm not being able to adapt the format to STATION 0, STATION 2, without any plus zeros or +, or -, or commas, or anything, as following in the image.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
Any way to label the elevation of an object where it is picked? For example, I'd like to be able to pick on the node of a feature line or 3D polyline (or any object really) and have a label placed that displays the elevation of the object at the point where it was picked. This could appear similar to the surface spot elevation label, but instead of getting it's elevation from a surface, it would come from the object where picked.
Alternatively, any way to create a label style, perhaps using the Note label, to display something like this? I don't even care if it is dynamic or not, static would be fine. However, I do need it to scale innovatively . Tool Pac has a feature that does this, but the label is just a polyline and text that is not annotative.
Is there any reason why a corridor model would not be respecting the manually entered super elevation values in the alignment? I have several stations that should be calculated with even super elevation values, but they aren't. For example, at station 0+080 on my alignment the left crown should be running at -3%, but it is actually being calculated at -2.47%. It isn't just one station; it's most of them. No overridden stations, vertical targets, etc in the corridor. Just a fairly straight-forward align (hor/vert) with super, simple assembly (two lanes, shoulder, daylight), simple corridor.
I need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
Is there a way to label or list a station at a specific elevation? I know how to list and label an elevation at a given station but I need to know where a specific (given) elevation is located on an alignment or profile. I don't care if this is listed or labeled on the alignment or profile, I just need to be able to get a station at a given elevation.
I have a sheet with labels on the TBC with station and elevation. If I plot the sheet everything shows up fine. If I publish to PDF, the elevation portion of the labels shows as ?
I am working on Street Improvement Plan using Civil 3D 2012. I have my centerline stationing set for major (100') and minor (50'). My street plan is kind of busy with a several call-out/label, leader etc. I want to set my my station for both major and minor with with decimal to read as 1+00 or 1+ 50 as opposed to 1+00.00... How to get rid of the decimal points.
I'm trying to use the _Wipeout_Circle block that ships with the straight-out-of-the-box NCS template (Civil 3D 2013 and Civil 3D 2014) to create a PI marker point in which the alignment is wiped out at the PI points. As you can see, the block itself works fine, but once used as a marker point it doesn't:
Here are the settings I'm using (again, this can be recreated straight from the NCS template):
I have been searching for a way to rotate surface spot elevation labels but have not been able to find a solution to do so. Has this feature been added to 2013 or 14? I do not want to use the point and label styles for my surface elevation, even though these can be rotated. I have several miles of roadway with many horizontal curves and would like the surface labels aligned with and along the centerline. I prefer not to update the spot elevations when the profile is revised.
C3D 2013 (latest updates), 2014 Infrastructure Design Suite
I've seen a label style somewhere that can label the elevation of vertices and elevation points on feature lines. How to style or a procedure for creating a style for this?
I've found a couple of blogs that layout the steps for a style but it seems there are a few ways to do it so I'm looking for what could be considered the most effective/versatile approach.
I am working in C3D 2011. The end station on my alignment is 163+02. The last major station label is 163+00. The label text overlap. I want to turn off the end label of 163+02. The end station is not checked in my Alignment Style or in the Geometry Points style. I am assuming there is a command in the Settings/Alignment/Commands that is overriding the changes I have made in individual styles. I have found some post concerning this from 2004 but they do not seem to be applicable in 2011.
Way to snap or drape the alignment (station) labels over a surface or bring them to the elevation of a selected surface. I'd like to know how to do this if there is a way, so when I look at surfaces in object viewer I can get an idea of where problem areas are from the stationing labels.
I am trying for last hour but cannot make this work. I have attached screen shot of a dynamic label with some text. The problem is as you add degree symbols and inch (") symbols and paratheses to the text, the leader starts to intersect the station value. I want to move the leader a little below the sta. value so the station vallue is readable. When I move the leader the text moves with it. I tried everything in edit label text option but cannot seem to fix it.
I was trying to find a way to not have the last ending Station Label show up on my centerline is there a override or way to tell it to just label to the last 100 or 50 foot station?
