I’ve had this problem with my proposed elevations for quite some time so I finally want to fix it while I’m a little slow. The problem I have is when I change scales, my elevation’s (in dragged state) leader vertex does not connect to my line. I’ve attached my lable styles...
View 7 RepliesI made a SitePlan in AutoCAD with all of the proper line scales set, but when I imported the file into Revit, they were all solid lines, not hidden or phantom styles as they should be. I fully exploded the site plan within Revit, but i still have yet to see a possible way to adjust the line type scales. So far it has only been telling me about how to change the line weight, which is not what I'm trying to do. If there is any information i can begiven on whether it is even possible to adjust the line type scale in Revit from an AutoCAD file
View 1 Replies View Relatedhow I can add in some vertex's at regular intervals on a fline or pline?
C3D 2013
I've seen a label style somewhere that can label the elevation of vertices and elevation points on feature lines. How to style or a procedure for creating a style for this?
I've found a couple of blogs that layout the steps for a style but it seems there are a few ways to do it so I'm looking for what could be considered the most effective/versatile approach.
I want to create new vertex points in feature line and 3dpol.
I have this:
try
{
if (obj.GetType() == typeof(Autodesk.AutoCAD.DatabaseServices.Polyline3d)) {
Polyline3d p3d = (Polyline3d)trans.GetObject(entRes.ObjectId, OpenMode.ForWrite);
[Code]....
In this code line:
oFtrLn.InsertFeaturePoint(punt, AeccLandFeatureLinePointType.aeccLandFeatureLinePointPI);
always catches the same Exception "the value is not within the expected range" .I have translated it because I get "El valor no está dentro del intervalo esperado". Perhaps is this: " Value does not fall within the expected range.".
I have tried it with different point3d values but always catches Exception.
With pol3d I have similar problem.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
how to have an option for the landing direction at the end of a leader line, or a way to edit one that has been created.
View 8 Replies View RelatedFor my dimension style, I have my text placement set to over dimension line, with leader, so I can drag the actual text outside the dimension line with a leader attached when necessary, but when I try to move the text outside of the dimension line it always draws the leader underlining the entire piece of text that I have moved. Is there a way to control the leader to attach to the middle of the line and not underline the entire piece of text when doing this operation?
View 3 Replies View RelatedI'v created my shape, snapped the vertex but cannot combine them to other sides, so when i go to smooth the shape it shows the disconnected edges/vertex...I'v attached a screen shot to show you the edges i mean (circled).
View 2 Replies View RelatedI'm modelling a character and I created the neck and now I want to connect it to the head but the problem is, he only allows me to weld some vertex, it's like he doesn't want both elements to share a edge or face, only vertex!(and yes, I attached the two elements).
when I want to create a face with those vertex he says: "illegal face" or something.
How do I modify the leader for station and offset labels to underline the top line of text?
View 3 Replies View RelatedC3D 2012 running with 64 bit Win7 all up to date on a capable Dell Precision
I want to add the leader part to the leader that is created when I drag a Station Offset label. This would be the part in a three point leader that goes horizontal for a short distance before the label text begins, similar to how a multi-leader is created. Looks weird having the C3D labels be the only "leadered" noted be without the landing.
I am using Map 3D 2013
I have several drawings in which I want to use a line type (centrex2) at a specific scale. The scale setting is exactly the same in all the drawings but in some the line type is coming out at different scales, all larger, but not the same or to a set factor. All the entities in question are poly lines (2d).
I have checked in all drawings that:
global scale factor and current object scale in the line type manager are the same (1.0)drawing units are the same (unitless)‘use paper space units for scaling’ is always deselected line type generation is always enabled.
If you change a view port scale of a view port that contains a bunch of annotative blocks.
How do you change the active annotative scale of all those blocks without individually picking the blocks.
So all the blocks appear the proper size in the viewport.
Is there anyway to prevent AutoCAD from converting a MTEXT leader with a block element attached to a BLOCK leader when doing a copy/paste? See screen shot.
2012-04-05 3-09-00 PM.jpg
i have problem in changing line directions that i'm using in my alignment.like buttom figure.
View 6 Replies View RelatedI know this is probably very simple and despite having been using CAD for 15 years I cant find the answer.
In every cad version Ive had, you can do the following:
-You draw a simple line, then you want the right vertex to move 500mm to the right, so you select the vertex, pull to the right with polar tracking, type 500, and job done. Same if say you wanted the same vertex to move up, down etc.
If i try this same thing with a line at an angle, it works as i would have thought, but if i do it with a horizontal line and want to move the vertex horizontally, it seems to act weird and draws the line 500 but from the left hand point.
I use many types of lines for drafting. I have to set a Linetype Scale depending on the scale asked by the client. For example if the client asks for 1:100 then my lines are set to 0.5. But if he suddenly changes her/his mind and asks for a 1:250 scale I have to change all the Linetype Scales to 2.5.
Is there something like "Annotation scale" for lines? So whenever I change the drawings scale my lines can be seen as they must be.
I use Coreldraw 11. and how to make one Line connect to another Line?
I know there is a way you select both Lines and have Coreldraw auto connect them?
I have changed the scale of my sheets and the scale of my floor plans to accomadate my new sheets, but now all of my thermostat, wall strips ect. are all way too big. How do I change this?
View 3 Replies View RelatedI have a little problem with trim in autocad 2012. After trimming some lines that cut through a circle there's a big gap between the circle and line, so there's no way i can create a polyline. How do I fix it?
here is the figure w/o trimming
pic1.png
Here it is after trimming
pic2.png
And as you can see there is space between the lines. How can I get the line to connect to the circle?
pic 3.png
create a code to add scales to the scale’s list?
I just want to have the necessary scales, so don’t want to add to the template.
The command function is basically to allow me type the value of the scale and based on that, adjust the properties of the scale. (Name appearing in scale list - Paper Milimeters - Drawing Meters)
Example:
>Command line: setscale
>type the value of the scale to create: 50
set 1:50 to default
Is there anyway of plotting a cad drawing from the model view screen so that certain linescales show? At the moment when I plot it will show hatched items without the outlines.
View 9 Replies View RelatedHow would you add features like radius, diameter to a leader line?
View 5 Replies View Relatedhow to change the thickness of leader lines. I'm editing a drawing done by someone else and I need to make the leader lines thicker. I tried changing the layer thickness and making sure the settings were such that the leader line thickness would be determined by the layer. I also tried channging the leader line thickness in properties and/or leader styles, but no luck there either.
View 6 Replies View Related3ds max 2012. I know most of the base of the software.But I never understood the technique of adding Polignim, vertexs and lines to the object to make it more realistic
Here I am trying to create a vertex: URL....
This is what happens after I create the vertex: URL....
The problem is that the vertex is not part of the line.You can see it because I moved the vetex. Some of the line was supposed to move with the vertex. This means that vetex is not part of anything. How to create vertex on the line.
I'm trying to add a single leader line to a drawing wihtout any text attached, the only way I can see is it use the 'leader text' command but now I can't detatch the text, is there any way to simply add leader only ?
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
The text commant in a drawing has the option to attach an arrow head with a leader. I want the text to be horizontal, so, i drag the leader line approximately horizontal.
Is there a way to make it horizontal? i tried pressing shift but no
I just started at this drafting job and inherited most of the graphics from others. Version: AutoCAD LT 2010.
Some of the leaders on my drawing somehow changed so that the arrowheads do not show. When I began working on the drawing, the arrowheads were fine, but while I have been working on the drawing, all of a sudden these leaders changed this property.
The properties manager lists these problem leaders as "line with no arrow." Although there is a drop-down menu to choose things like "line with arrow," the "no arrow" option does not change when I pick anything else.
I want to force the Multileader landing to go left when the program wants to automatically form it to the right. How can you choose/change the direction of the landing line and side on which the text will be placed.
AutoCAD 2011
I have a leader that I want to make the line part of thicker (already made the leader arrow head bigger). I saw that it appeared to be based on dimension style, and I tried changing the lien thickness in there although as we use color dependent plot files, not line weight dependent plot styles, this had no effect.
View 3 Replies View Related1.) How to paste (leader or line or text) objects to many layouts at once (same time) without opening all the layouts. (I am having 5 CAD files, each file has 25 layouts).
2.) How to delete objects (leader or line or text) from many layouts. I can select by filter command from all the layouts but, when you delete it deletes only from the current layout.