i've made a serpantine curve that starts from one line of alignment and end on the other line.
i wanted to know how can c change alignment direction when these two feature line and alignment meet each other in order to change the alignment path?
i have problem in changing line directions that i'm using in my alignment.like buttom figure.
View 6 Replies View RelatedI have cut several sections at different points along a road alignment. The sections are cut facing the same direction as the alignmnet. Is there a way to reverse the section direction without changing the alignment direction?
View 6 Replies View RelatedC3D 2013, Win 7, 64 bit
When I try to create a feature line using an alignment/ profile, sometimes it gives me a feature line for the entire alignment, even though my profile is only a small segment. I made sure I selected the correct profile, and I even deleted all other surface profiles just in case. But it still gives me a wonky feature line for the entire alignment.
However, in the same file, other profiles have worked perfectly.
I need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
View 5 Replies View RelatedWindows 7, 64 bit, Civil 3D 2010
I'm trying to create a surface using feature lines. I have an alignment and profile that I have created a dynamic feature line. However, on a horizontal curve, it apparently creates a vertex at the start and beginning of the curve, and nothing on the curve, so it triangulates between those two points and that's it.
Do I need to play with spiral tessellation (0.25), mid-ordinate distance (0.1) to get some points along the curve?
is there is any way to reverse the alignment direction
View 3 Replies View RelatedCan I reverse the direction of an existing horizontal alignment line in C3d 2011?
View 9 Replies View RelatedChanging alignment path in my drawing,how can i do that? There is a pic too.
View 1 Replies View RelatedI imported 5182 points (in the NEZ format) into my AutoCAD Civil 3D 2013 (English Metric) and then created a Surface from these points (Style: Contours 1m and 5m (Background)). I selected a polyline => Alignment => Create Alignment from Objects - see the attached file. How can I verify the direction of the alignment I just created?
View 2 Replies View RelatedI using a data reference/shortcut to properly label an alignment in paperspace. However when I reference the alignment in and apply the labels the aren't the same as the original alignment that I am referencing. Is there a setting where I am supposed to apply a new beginning station.
Also it seems as though the stationing(distance) isn't even matching up 1:1 with the original drawing. For example in the original base drawing my alignment starts at 10+00 with the next PI at 14+76.98, but the stationing on the reference alignment starts at 0+83.33 with the very same PI being labeled as 1+23.08. So the very same distance is 476.98' in the real design and the drawing it's being referenced in, but the stationing of the referenced alignment shows it as 39.75 Units.
I've attached a screen of the beginning of the alignment.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
Using Civil 3d2012, Is it possible to change the alignment label style set after the alignment has been created? For example, for an alignment that was created with alignment label set X - change the label set to alignment label set Y? It seems like this should be pretty easy, I must be missing something obvious.
View 2 Replies View RelatedI have a question on Alignment PI's. (Point of Inflection/Intersection)I have an alignment where some PI's have curves, others are merely hard bends.
Is there a way to automatically label the PI's even if they have an associated curve? (I'd like PI, PC and PT)Alternatively, can I only show markers at PI's without curves?
I'm trying to edit some existing alignments. When I create new entities, they do not show up in the alignment grid view. Why is this?
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
Launching alignment grid view/alignment entities,
I’m wondering if there is a way to launch alignment grid view/alignment entities (attached) without the need to first launching “alignment”? This dialogue box is quite essential in editing the values of radius, degree of curvature and deflection angle for the selected curve.
Can I inherit the station from one alignment as the begin station for another alignment?
For example. Alignment 1 is 1000 ft long and starts at sta 0+00.
At sta 8+01, Alignment 2 begins and goes off in another direction.
I manually enter 8+01 for begin station Alignment 2. Life is good. Still in the design stage, and customer needs to modify Alignment 1 to avoid something. Now Alignment 2 intersects Alignment 1 at sta 8+15, but same N/E coordinates.
I manually enter 8+15 for begin station Alignment 2.
It would be better if Alignment 2 could inherit the begin station based on the new stationing from Alignment 1.
Now, in my understanding, the flow arrow should either be rotated 0, or 180 (pi radians). But clearly, some of them like to have their own mind about things, and decide on some other rotation. It seems that on the steep slopes, the arrows go a bit skew.
I think the skew is related to the actual elevation difference of the segment, rather than the steepness of the slope. A long segment with 15% slope has a worse skew than a short segment at over 30%, presumably because the elevation difference from the start to the end of the segment is larger.
My alignment ticks use the stanard Aecc Tick block. It is on layer 0/bylayer/bylayer etc and the style is set by layer. They display correctly in the source drawing but when I xref that drawing into others, the ticks change colour based on what every the current layer is in the host drawing. If the current layer is 0 they dispaly correctly, if my current layer has a colour 5 associated with it then my xref ticks regen to blue. This only happens with the tick not the text.
View 8 Replies View RelatedIs it possible to modify a label set to a new starting station, e.g., instead of the alignment starting at 0, change it to start at 100?
View 9 Replies View RelatedCan you reverse the direction of an auto feature line generated from a corridor in C3D 2012?
View 4 Replies View RelatedI draw an alignment for road. I turned off design criteria and i used data from manual for my country Slovenia. I need spiral in, curve and spiral out on alignment. Finally i got that alignment. Then i insert sample lines along the alignment. Then i saved autocad civil 3d file and shut down the program. When i reopen file, i see that sample lines after the spiral in being erased. Sample lines stayed along first tangent, after that they were erased.
View 9 Replies View RelatedThe stationing along my alignment line is missing. I do believe it was there yesterday at 5 but hey who knows. How do I restore it the PI stationing is there.
View 4 Replies View RelatedI am just starting to use C3D 2013, and have just finished creating a new template for use in 2013 by importing the styles from our 2012 template. I am having an issue with an alignment style. The problem is that every line extension after the first one ends up being on the same layer as the curve (see attachment). They are supposed to be on a seprate layer as they were in our 2012 template.
View 1 Replies View RelatedI have a roadway alignment and it is ending on 4+50.86, we simply want the alignment end to read on 4+51. is it possible to make this happen?
View 4 Replies View RelatedChanging the default of “design speed” appearing in the create alignment,I’m wondering how the design speed appearing in the “create alignment” dialogue box can be changed such that the second time the “create alignment” dialogue box is launched then the new value for the speed is displayed.
View 2 Replies View RelatedI am setting up a template for my company and have noticed that I can't change the line/curve/spiral LTscale:
I have chosen a layer with the CENTER linetype for my line/curve/spiral in the style editor. The Alignment appears correctly with the CENTER linetype. However I want to make the dashes a bit bigger, so I change the LTscale in the style editor to 4, but then nothing changes.
When I change the same setting for the "line_extensions" element to the same layer, these WILL update when changing the LTscale.
All my LTSCALE, PSLTSCALE, MSLTSCALE are set to 1.
All other lines, such as polylines and featurelines, as well as the line extension lines of the alignment update correctly. Its just the alignment line.curve/spiral elements that do not.......
Are these locked somewhere?
Intel Xeon E31230 - 3.20 GHz
4.00 GB RAM
Windows 7 Professional - 64-bit
Nvidia Quadro 600 - 1GB DDR3
I created view frames and sheets for a number of alignments. Is there a way to turn off a match line not associated with the main alignment for a particular viewport.
Or did I missed a setting somewhere that should turn this off automatically?
Inserted an alignment line table. It's in model space and viewported (locked) to the layout. On the screen it looks fine but during print preview and printing it comes out too small. Can this be controlled?
View 8 Replies View Relatedi have an issue in with my created sheets that does not show vertical alignment data. everything on the bands shows up nicely but the lines, curves and labels profile are missin.
see the attached image. you can notice from the image that there is no a signle data..
C3D 2012...but this feature has probably been in C3D for sometime
1-What is a 'Line Marker in Section' Section component of an Alignment Style?
2-How is it used (example )?
How can I change direction of a line feature? Have any redy default command to do it?
View 8 Replies View Related