I want to be able to make a alignment table with northing and easting coordinates for the following:
bop
pi's
eop
Is this possible? The closest I get is to make a curve table with the pi coordinates and no bop or eop coord'.
Civil 3D 2014
Win 7
I am trying to create a table that will incorporate info from structures and pipes. In C3d 2010 I want to make a CB chart which will show the pipe size, starting structure and invert. I would also like to include the CB rim elevation but that would be under the structure table. Is there any way I can combine the RIm elevation with the pipe table?
View 4 Replies View RelatedIt is possible to create a table for an alignment as shown in the example attached?
View 1 Replies View RelatedI'm trying to add an alignment table, but the curves seem to be labelled twice. When I first labelled the alignment, the curves were C???, so I tried again. After a lot of messing around, I finally got C1, C2, etc., but the table lists C1 & then C?. I've thawed & turned on all the layers, but there aren't any C??? labels on the alignment. Another alignment in the same drawing worked fine.
View 4 Replies View RelatedIf there was any way to get deflection angles of an alignment into a table? I finally figured out how to get C3D to label them using the add note label. If this is not possible, is there a way to make a table of the notes? I am using C3D 2013 version if it makes any difference.
View 4 Replies View RelatedI need elevation data from a surface. I need an elevation every 15' along an alignment or feature line. I would like the information as a table. I am not sure how to do this.
View 5 Replies View RelatedI need to produce a better standard table for our company, but need to know how it would be possible to display only either the START STAKE VALUE/ STATION or END STAKE VALUE/STATION in the appropriate column. If I can achieve this i would not need to details for straight segments as indicated in the details column.
View 5 Replies View RelatedI have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.
To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.
I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?
Inserted an alignment line table. It's in model space and viewported (locked) to the layout. On the screen it looks fine but during print preview and printing it comes out too small. Can this be controlled?
View 8 Replies View RelatedI want to create a Curve table for an alignment.
You are able you get range of properties, i.e length, chord length, start/end chainages, mid-ordinate.
I've notice lets for arguement sake 'chord length' text component editor is: <[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]> but is it possible to modify the code so i can insert half a chord length.
Ive tried
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]>/2 ---- doesn't work
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]/2> ---- doesn't work
<[Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)/2]> ---- doesn't work
<[1/2*Chord Length(Um|P3|RN|AP|GC|UN|Sn|OF)]> ---- doesn't work
Is there a way to create a table of stations and offsets along a specific alignment at chosen locations?
Dynamic would be preferred.
I'm currently using version 2013.
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013
How can you add the chord bearing, chord length, and tangent to an alignment table with the curve data in it? I have the length and direction but cannot figure out why the others will not load and update in the chart. I am using Autocad Civil 3D 2012
Autocad Civil 3D 2014
Windows 7 Prof. SP1 (64-bit)
Precision T3500
Intel (R) Xeon(R) CPU W3550 @ 3.07 GHz
6.00 GB
NVIDIA Quadro 4000
Is there a way to setup vertical alignment of text in a cell for the entire table, when using Table Tool? It is possible for a single cell, but when selecting a table (or multiple cells) this option is not available.
View 5 Replies View RelatedI have a general table in my engineered print. It consists of basic columns with text. How can i have Inventor refresh the data if i change the Excel without having to delete and re insert a table ?
Autodesk Inventor Professional 2011
I am creating a table where I want the cell contents to be aligned Middle Center. I can set that up in the table definition and it seems to be in place once the table is in the drawing. If I type text into the cell the alignment is as expected. Whenever I type a number the aligment changes to Top Right. I can go back into the cell and reset the alignment to Middle Center. If I then delete the cell contents, exit the cell then return to the cell and enter a number the alignment returns to Top Right. I want the table to start off empty so others can enter informaiton as it becomes available. Is there a way to have the cell alignment stay the way I wnat it regardless of what I enter into the cell? I tried changing the cell format to text but the instant I entered a number it switched back to a number format and aligned Top Right.
View 2 Replies View Relatedi've made a serpantine curve that starts from one line of alignment and end on the other line.
i wanted to know how can c change alignment direction when these two feature line and alignment meet each other in order to change the alignment path?
I using a data reference/shortcut to properly label an alignment in paperspace. However when I reference the alignment in and apply the labels the aren't the same as the original alignment that I am referencing. Is there a setting where I am supposed to apply a new beginning station.
Also it seems as though the stationing(distance) isn't even matching up 1:1 with the original drawing. For example in the original base drawing my alignment starts at 10+00 with the next PI at 14+76.98, but the stationing on the reference alignment starts at 0+83.33 with the very same PI being labeled as 1+23.08. So the very same distance is 476.98' in the real design and the drawing it's being referenced in, but the stationing of the referenced alignment shows it as 39.75 Units.
I've attached a screen of the beginning of the alignment.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
Using Civil 3d2012, Is it possible to change the alignment label style set after the alignment has been created? For example, for an alignment that was created with alignment label set X - change the label set to alignment label set Y? It seems like this should be pretty easy, I must be missing something obvious.
View 2 Replies View RelatedI have a question on Alignment PI's. (Point of Inflection/Intersection)I have an alignment where some PI's have curves, others are merely hard bends.
Is there a way to automatically label the PI's even if they have an associated curve? (I'd like PI, PC and PT)Alternatively, can I only show markers at PI's without curves?
I'm trying to edit some existing alignments. When I create new entities, they do not show up in the alignment grid view. Why is this?
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
Launching alignment grid view/alignment entities,
I’m wondering if there is a way to launch alignment grid view/alignment entities (attached) without the need to first launching “alignment”? This dialogue box is quite essential in editing the values of radius, degree of curvature and deflection angle for the selected curve.
I've spent the last 4 hours searching for an answer to this question, but I simply can't find one.
As a start I think you have to know that I'm currently using AutoCAD 2012.
Here's the problem: I need to extract some info from an AutoCAD table to a reference file that can be opened in Microsoft Excel. Everything I find on the subject is actually an answer to the question "How does <DATAEXTRACTION> work?" or "How to do an extraction of DATA in AutoCAD?"....
In this particular case I have a set of production drawings (cut tickets) for manufacturing of stone. And in every single sheet I have this material schedule or a table, if you wish, that is made with an AutoCAD table. In this schedule I have the height, width and thickness of the stone plate and with a function it measures it's area and volume. What I want to do is to extract those values into a reference file that I can open with Microsoft Excel, as I already said.
How exactly?
Can I inherit the station from one alignment as the begin station for another alignment?
For example. Alignment 1 is 1000 ft long and starts at sta 0+00.
At sta 8+01, Alignment 2 begins and goes off in another direction.
I manually enter 8+01 for begin station Alignment 2. Life is good. Still in the design stage, and customer needs to modify Alignment 1 to avoid something. Now Alignment 2 intersects Alignment 1 at sta 8+15, but same N/E coordinates.
I manually enter 8+15 for begin station Alignment 2.
It would be better if Alignment 2 could inherit the begin station based on the new stationing from Alignment 1.
Is there a way to force the table and table text height to stay constant despite the scale? I can do it for Point Label Styles with an Expression. But in 2011 there is no way to build an expression for a table style.
I want to create tables in the drawing where the points are and then plot them from a drawing they're Xrefed in to. The tables are too small but zooming in doesn't make them any bigger because the scale of the viewport changes and they adjust.
I want to know if you can link AutoCad tables to other Autocad tables on different layouts. Say I have ten sheets, each with a table for quantities of pipe length, and one sheet with a total of all quantities. Can I link cells from each separate layout sheet to the main table sheet, so that I can add them all for project totals?
View 3 Replies View RelatedI imported Google earth surface (at eye alt 600m) to civil 3d 2012 and created an alignment of length 181m.
When I exported same alignment to Google earth , it showed the length as 190m ( the difference increases with increase in length of alignment) And also the profile view of the alignment in the Civil D & Google earth varies.
We use map info as our native GIS and can use these .TAB files with MAPIMPORT in C3D, but what I would really like to do is use MAPCONNECT like can be done for .SHP files, etc.. I've inquired with [URL].....and they have confirmed that their FME product doesn't support 2013.
View 8 Replies View RelatedI am running 2012 C3d and I am having an issue when a drawing is freshly opened, some of the profile data is not showing and it will show up after I sync the different information that is missing.when I run a publish of multiple projects that info doesn't show and I have to go into each project to sync the info and plot each sheet separately.
View 6 Replies View RelatedI have some topo drawings (contours with Z elevations) and am trying to create lines representing where we did our field work. I then want to extract X, Y & Z coordinates of points along those lines (either where they cross the contour lines or at regular intervals along the lines that I create). I can create surface(s) of the topo that I have, but my questions are what kind of lines would be the best to use to represent our lines of field work (3D poly lines, feature lines, or alignments) and once I get those laid in, how do I extract the XYZ info into a text format of some kind (excel, csv, etc.)?
View 3 Replies View RelatedI created an enclosed "object" adding break lines to two different surfaces.
The blue surface shown on the attached drawing is a set of break lines added to "Surface A" and then the red is the other set of break lines added to "Surface B". I have already generated the volume enclosed within the surfaces by doing a surface to surface volume calculation.
My Question:I want to combine the enclosed volume created by Surface A & Surface B into a 3D "Block" that give me the volume information.
Is there a way to display the projection (FL-W83) or Datum (NAD83) of a DWG file in the titleblock? Maybe using fields, or a diesel expression of some sort? I belive the information resides in the .NET framework, how can I get that into my titleblock?
HP Z400 Workstation
Intel Xeon W3550 -Cores 4
12GB Triple-Channel DDR3 @ 533MHz
2-HP LE2201w @ 1680x1050
ATI FirePro V3800 (FireGL) (HP)
MS Windows 7 64-bit
