AutoCAD Civil 3D :: Alignment Table - Setting Out Data - Stake / Station Value

Dec 2, 2013

I need to produce a better standard table for our company, but need to know how it would be possible to display only either the START STAKE VALUE/ STATION or END STAKE VALUE/STATION in the appropriate column. If I can achieve this i would not need to details for straight segments as indicated in the details column.

View 5 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Point Table With Alignment Station Data Field?

Jun 1, 2010

I have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.

To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.

I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?

View 9 Replies View Related

AutoCAD Civil 3D :: Angle-distance Method To Stake Out Horizontal Alignment By Total Station

Aug 3, 2013

Angle-distance method to stake out the horizontal alignment by total station,Assuming that the total station with reflector is the tool that it is intended to lay out the circular curve after being designed then the only way to do so is to construct a table that contains angle-distance values.

 I’m wondering if the C3D can provide this table (attached)

View 9 Replies View Related

AutoCAD Civil 3D :: Alignment Setting Out Table?

Nov 18, 2013

It is possible to create a table for an alignment as shown in the example attached?

View 1 Replies View Related

AutoCAD Civil 3D :: Alignment Begin Station Inherited From Another Alignment

Aug 8, 2012

Can I inherit the station from one alignment as the begin station for another alignment?

For example. Alignment 1 is 1000 ft long and starts at sta 0+00.

At sta 8+01, Alignment 2 begins and goes off in another direction.

I manually enter 8+01 for begin station Alignment 2. Life is good. Still in the design stage, and customer needs to modify Alignment 1 to avoid something. Now Alignment 2 intersects Alignment 1 at sta 8+15, but same N/E coordinates.

I manually enter 8+15 for begin station Alignment 2.

It would be better if Alignment 2 could inherit the begin station based on the new stationing from Alignment 1.

View 7 Replies View Related

AutoCAD Civil 3D :: Add Chord Bearing Chord Length And Tangent To Alignment Table With Curve Data

Apr 12, 2012

How can you add the chord bearing, chord length, and tangent to an alignment table with the curve data in it?  I have the length and direction but cannot figure out why the others will not load and update in the chart.  I am using Autocad Civil 3D 2012

Autocad Civil 3D 2014
Windows 7 Prof. SP1 (64-bit)
Precision T3500
Intel (R) Xeon(R) CPU W3550 @ 3.07 GHz
6.00 GB
NVIDIA Quadro 4000

View 5 Replies View Related

AutoCAD Civil 3D :: Alignment Station Modification

Nov 21, 2012

When an alignment needs to have stationing modified, what is the best process for this when a proposed grade line and corridor have been established?  I know the proposed grade line can be edited via edit profile geometry>profile grid view. 

But what from I have found each station has to be modified individually, which is cumbersome.  I would hope to be able to modify the proposed grade line by changing only the beginning station and the rest would update, similar to the alignment.

C3D 2011, (latest updates)
Win 7 Pro, 64-bit
16 GB RAM 

View 8 Replies View Related

AutoCAD Civil 3D :: Zoom To A Station On Alignment?

Jan 15, 2013

Like entering a station and going there?I've used the 'SO with Zoom C. That is not simple.12+ miles of a single road alignment with 3 equation stations makes for a LOT of panning.

View 4 Replies View Related

AutoCAD Civil 3D :: Re-Station Alignment After Editing?

Jan 13, 2013

After editing an alignment in my drawing the stationing did not update to the new edited alignment. I tried selecting the alignment and in alignment properties changing the end stationing, but I get the error "Either outside alignment limits or within gap created by a station equation". The stationing stops at my first edit point 66+24 when the total length of edited alignment is 103+15. Is there a way to re-station alignment.

View 3 Replies View Related

AutoCAD Civil 3D :: Points On Alignment At Station With Description?

Apr 24, 2013

i need to put points on an alignment at each station. i've figured that part out. what i want is the station label to be the point description. i don't see a way to do this without editing each point which is way too time consuming.

Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2012 SP3.0

View 9 Replies View Related

AutoCAD Civil 3D :: Possible To Add Prefix To Alignment Station Label

Jun 22, 2012

Is it possible to add a prefix to an alignment station label (ex. A 100+00.00 or B 100+00.00) in Civil 3D 2010 or later?

View 5 Replies View Related

AutoCAD Civil 3D :: Alignment Station Offset Label

May 19, 2012

I am trying for last hour but cannot make this work. I have attached screen shot of a dynamic label with some text. The problem is as you add degree symbols and inch (") symbols and paratheses to the text, the leader starts to intersect the station value. I want to move the leader a little below the sta. value so the station vallue is readable. When I move the leader the text moves with it. I tried everything in edit label text option but cannot seem to fix it.

[URL]

View 5 Replies View Related

AutoCAD Civil 3D :: Alignment PI Station Report Settings?

Feb 1, 2012

I am trying to export an Alignment PI Station Report. I've set all the settings I can find to round coordinates to 4 decimal places, Distance to 2 decimal places, and Direction to the nearest second (DMS). When I execute the PI Station Report, the Distance is 3 decimal places and the Direction is to the nearest 100th of a second. how to get these to the correct decimal place? I managed to change them to the correct decimal place for a Station & Curve Report, but not for the PI Station Report. Also, for the Northing/Easting coordinates, I want to remove the commas (for example, a Northing of 3,058,715.3774' should read 3058715.3774').

View 4 Replies View Related

AutoCAD Civil 3D :: How To Define The Station Control From The End Of Alignment

May 23, 2012

if it's possible to define the stationing of the alignment from the end of the alignment till the start.

I have a special situation where the end station is fixed in one point (ex. km 3+125,00) and till there I can change the alignment.

I want to be all the time the end in one station value.

View 7 Replies View Related

AutoCAD Civil 3D :: Move Station On Existing Alignment?

Aug 23, 2012

Is there a way to move the station on an existing alignment?  For example, I have an alignment created and want to move station 10+00 so it represents a different point on my alignemnt.

View 1 Replies View Related

AutoCAD Civil 3D :: Set Up Alignment Station Offset Label

Oct 7, 2013

I would like to set up an alignment station offset label that when in the dragged state, offsets the arrowhead from the actual insertion point on the alignment in any direction and distance I specify. I am preparing some plans for a water line. I am working at a 1"=200' scale so all of the blocks representing fittings are scaled up so they are legible.

In some instances, the fittings are right next to each other. If I place an alignment station offset label at the actual station and drag it away from the alignment, the arrowhead is pointing to the station but not the fitting. Is there a way to offset the arrowhead of a C3D label in dragged state other than in the direction of the leader?

View 1 Replies View Related

AutoCAD Civil 3D :: Data Reference Alignment Stationing Differs From Original Alignment

May 3, 2012

I using a data reference/shortcut to properly label an alignment in paperspace. However when I reference the alignment in and apply the labels the aren't the same as the original alignment that I am referencing. Is there a setting where I am supposed to apply a new beginning station.

Also it seems as though the stationing(distance) isn't even matching up 1:1 with the original drawing. For example in the original base drawing my alignment starts at 10+00 with the next PI at 14+76.98, but the stationing on the reference alignment starts at 0+83.33 with the very same PI being labeled as 1+23.08. So the very same distance is 476.98' in the real design and the drawing it's being referenced in, but the stationing of the referenced alignment shows it as 39.75 Units.

I've attached a screen of the beginning of the alignment.

Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM

View 5 Replies View Related

AutoCAD Civil 3D :: Reset Alignment (x Backward From Start Station)

Aug 31, 2012

I am working on road improvements, the City my client want to extend the improvement longer form the original scope of work. I am already completed the alignment and road profile centerline and the production plan is 100% completed.

What I need to do is to change and  extend the alignment 750 feet backward from the original station (10+00). If I could explain correctly, I want to start the station @ 7+50 (backward from 10+00) and no changes on forward stationing.

What is the best way without doing re-creating alignment.

View 3 Replies View Related

AutoCAD Civil 3D :: Label Two Station On One Alignment In Construction Note?

Apr 11, 2013

Looking for a way to label two station on one alignment in a construction note. 

Civil 3D 2013 (SP1)
Dell T3500
Win 7 Pro X64
Intel Xeon 3.2 GHz
24 GB ram
NVIDIA Quadro 4000

View 2 Replies View Related

AutoCAD Civil 3D :: Alignment Report That Includes Both Station And PI Information

Mar 19, 2012

I have a 2 mile alignment of a railroad loop track and I am looking to generate a report that include both information at 50' increments and the curve data, i.e. PI, PT, so I can generate a staking report for the surveyors. I noticed that there are pre-canned reports that handle one or the other but not both.

View 2 Replies View Related

AutoCAD Civil 3D :: Change Default Beginning Alignment Station?

Jun 4, 2007

where to change the default beginning station from 0+00 to 1+00 in my civil 3d profile template (dwt), so that the beginning station is always 1+00, unless the user changes it.

View 3 Replies View Related

AutoCAD Civil 3D :: Offset Points Along Alignment With Station And Description

Apr 9, 2012

I am trying to find a way to offset points along an alignment showing station, offset and description. This is for a plan and profile sheet see attached example clouded in red.

View 2 Replies View Related

AutoCAD Civil 3D :: Alignment Station Offset In Profile View

Apr 27, 2013

Is there anyway to display Alignment Station Offset Label at Profile View because sometimes i want to display where is the phisical noze location in profile view also my attached file display what i have in my label and how display my label in profile view.

View 7 Replies View Related

AutoCAD Civil 3D :: Alignment Station Offset Label Blind Spot

Mar 26, 2013

I am labeling station and offsets from my alignment for curb returns and such and for some reason if the offset point is directly perpendicular from an alignment PC or PT the label can't find the alignment information. It's like there is a blind spot.

View 4 Replies View Related

AutoCAD Civil 3D :: Editing Multiple Alignment Station Offset Labels

Mar 19, 2013

I am trying to edit labels for a particular alignment. All labels are along the same alignment and use the same alignment style. I need to change "defl." in each of those labels to "defl:". So simply changing the period to a colon. But it is a lot of work to go through each label and then in edit label text and then change it. Plus, I have to do this on 12 sheets. That's like 300 labels! Is there a quick way to achieve this. If it were simple mtext or dtext then I could use the find and replace option, but these are civil 3d alignment station offset labels? Is there a lisp that can accomplish this task? I am using Civil 3D 2010.

View 3 Replies View Related

AutoCAD Civil 3D :: Alignment PI Label With Lat Long / Station And Delta Angle

Feb 27, 2013

We are trying to label the intersection points on an alignment with the following info:

Sta:
Delta Angle
LAT
LONG

We can make it work with a Northing and Easting, but there is no option for a LAT LONG under the tangent intersection labels.  I tried to make an expression that would format a Northing as a LAT but it just gave me jibberish.

I was able to do it but adding a point at each PI and making a point reference text, but you then have to select a different point for each label....  which works but it is still a multi step process.

View 9 Replies View Related

AutoCAD Civil 3D :: Changing Alignment Label Sets Starting Station

Sep 19, 2011

Is it possible to modify a label set to a new starting station, e.g., instead of the alignment starting at 0, change it to start at 100?

View 9 Replies View Related

AutoCAD Civil 3D :: Changing Alignment Station Labels To Round To Nearest Number

Aug 21, 2012

I have a roadway alignment and it is ending on 4+50.86, we simply want the alignment end to read on 4+51. is it possible to make this happen?

View 4 Replies View Related

AutoCAD Civil 3D :: Change Alignment Station Offset Label Default Layer?

Oct 29, 2012

how do you change their layer? i have been through the settings tab under "alignment", "station offset". i also right clicked on one and went through the properties.

View 4 Replies View Related

AutoCAD Civil 3D :: Setting Station Range In View Frames Thus In Sheets

Aug 8, 2012

there i wanted to know a method to control my view frames range or how to do so in the sheets , 

as per attachment i get the Profile view , out of frame 

Yeah Will Not that much :
Sony VPCCW26FA
Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated

View 3 Replies View Related

AutoCAD Civil 3D :: Data Band At Wrong Station

Jun 13, 2013

A coworker who is no longer with us set up the data band styles & settings in our template, and they were working fine in 2011.  Then, on a new job in 2011, I encountered this problem.  I gave up.

Now I'm working in 2013.  The template was brought forwards, so it's the same settings, and I'm hitting the same problem as before.  The difference is this time I'm working on a really long profile, and I really really want the bands to work.

Here's the problem.

The ones I checked in blue are not part of the data band.  They are profile view labels, and they show the correct stations.

The ones circled in red are the data band.  As you can see I need to work on my gap settings, but that's not my problem.  The problem is the location of these labels.  There is indeed a PVI at station 1+165, but the label is 40m away from that station!  I don't know where to start digging to find the setting to tell that label to move 40m to the right, and tell 1+135.86 to move 20m to the right.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved