I have a 2 mile alignment of a railroad loop track and I am looking to generate a report that include both information at 50' increments and the curve data, i.e. PI, PT, so I can generate a staking report for the surveyors. I noticed that there are pre-canned reports that handle one or the other but not both.
View 2 RepliesI am trying to export an Alignment PI Station Report. I've set all the settings I can find to round coordinates to 4 decimal places, Distance to 2 decimal places, and Direction to the nearest second (DMS). When I execute the PI Station Report, the Distance is 3 decimal places and the Direction is to the nearest 100th of a second. how to get these to the correct decimal place? I managed to change them to the correct decimal place for a Station & Curve Report, but not for the PI Station Report. Also, for the Northing/Easting coordinates, I want to remove the commas (for example, a Northing of 3,058,715.3774' should read 3058715.3774').
View 4 Replies View RelatedCan I inherit the station from one alignment as the begin station for another alignment?
For example. Alignment 1 is 1000 ft long and starts at sta 0+00.
At sta 8+01, Alignment 2 begins and goes off in another direction.
I manually enter 8+01 for begin station Alignment 2. Life is good. Still in the design stage, and customer needs to modify Alignment 1 to avoid something. Now Alignment 2 intersects Alignment 1 at sta 8+15, but same N/E coordinates.
I manually enter 8+15 for begin station Alignment 2.
It would be better if Alignment 2 could inherit the begin station based on the new stationing from Alignment 1.
I need to conceive a Incremental Station Elevation Difference Report (Toolspace - Toolbox) where each station is worth 20 meters. But I don't know how to set C3D 2013?
View 2 Replies View RelatedI am trying to use the Station Offset to Points report from the Reports manager. Currently, as far as I ca see, there is no way to select a group of points to include, either by point group or selection from the drawing. There is only "Select All' or "Deselect All". I want a report that will show the station, offset, raw or full description and elevation of a group of points related to an alignment/street. I don't see that option.
View 2 Replies View RelatedI have more than 200 alignments of road network. The profile design are already done for this. I want to generate Incremental Station Elevation Difference report for all the alignments.
For this I have to select each alignment, its respective profile & generate the report for it. As am having more than 200 Alignments I will have to repeat the process 200 times. Is there any way to make the process easier like generating report for all the alignments at once?
A co-worker asked if I could create a report that listed the station and offset values for selected points & alignment. After selecting "execute" for the Station Offset to Points report, the file gets hung up before I can select the points and alignment I want.
I've tried xml-ing out the desired points & alignment into another file and running the report from..
All other reports under Alignment and Points work fine (drawing does not have other C3D objects).
I'm using C3D 2011 version 3.
Civil 3D 2013
Toolspace > Toolbox > Reports Manager > Points > Station Offset to Points
why point number 9 comes after 1 instead of 8?
Clicking on the column headers to sort does not work.
Found another report of this, but in an earlier version of C3D.
[URL]
When I Create a Station offset to points report, the points are out of order and it does not display all of the points.
View 2 Replies View RelatedIs there a way to included the radial bearings of curves for alignment reports generated for the report manager? I know the curves are tangent because I made them so, but the guy checking my report for errors doesn't know that. I don't know any xml.
View 1 Replies View RelatedI want to generate Civil 3D point of intersection alignment report including following columes.
PI Row station
Delta Angle
PI Includead Angle
Is this possible?
AutoCAD Civil 3D 2012 SP 2
When an alignment needs to have stationing modified, what is the best process for this when a proposed grade line and corridor have been established? I know the proposed grade line can be edited via edit profile geometry>profile grid view.
But what from I have found each station has to be modified individually, which is cumbersome. I would hope to be able to modify the proposed grade line by changing only the beginning station and the rest would update, similar to the alignment.
C3D 2011, (latest updates)
Win 7 Pro, 64-bit
16 GB RAM
Like entering a station and going there?I've used the 'SO with Zoom C. That is not simple.12+ miles of a single road alignment with 3 equation stations makes for a LOT of panning.
View 4 Replies View RelatedAfter editing an alignment in my drawing the stationing did not update to the new edited alignment. I tried selecting the alignment and in alignment properties changing the end stationing, but I get the error "Either outside alignment limits or within gap created by a station equation". The stationing stops at my first edit point 66+24 when the total length of edited alignment is 103+15. Is there a way to re-station alignment.
View 3 Replies View RelatedNothing appears as the “Stakeout Alignment Report” is executed,I wanted to execute the “Stakeout Alignment Report” (attached) but nothing appears! This is despite the fact that:
-The IE is set as default browser (attached)
-The Active X is enabled (attached)
i found a way to get a report of my cogo points relative to an alignment i.e. station offset. problem is, i have thousands of points in my drawing. is there a way to get only a few, or a group of points to show up on the report instead of ALL of them?
View 1 Replies View Relatedi need to put points on an alignment at each station. i've figured that part out. what i want is the station label to be the point description. i don't see a way to do this without editing each point which is way too time consuming.
Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2012 SP3.0
Is it possible to add a prefix to an alignment station label (ex. A 100+00.00 or B 100+00.00) in Civil 3D 2010 or later?
View 5 Replies View RelatedI am trying for last hour but cannot make this work. I have attached screen shot of a dynamic label with some text. The problem is as you add degree symbols and inch (") symbols and paratheses to the text, the leader starts to intersect the station value. I want to move the leader a little below the sta. value so the station vallue is readable. When I move the leader the text moves with it. I tried everything in edit label text option but cannot seem to fix it.
[URL]
if it's possible to define the stationing of the alignment from the end of the alignment till the start.
I have a special situation where the end station is fixed in one point (ex. km 3+125,00) and till there I can change the alignment.
I want to be all the time the end in one station value.
Is there a way to move the station on an existing alignment? For example, I have an alignment created and want to move station 10+00 so it represents a different point on my alignemnt.
View 1 Replies View RelatedI would like to set up an alignment station offset label that when in the dragged state, offsets the arrowhead from the actual insertion point on the alignment in any direction and distance I specify. I am preparing some plans for a water line. I am working at a 1"=200' scale so all of the blocks representing fittings are scaled up so they are legible.
In some instances, the fittings are right next to each other. If I place an alignment station offset label at the actual station and drag it away from the alignment, the arrowhead is pointing to the station but not the fitting. Is there a way to offset the arrowhead of a C3D label in dragged state other than in the direction of the leader?
I am working on road improvements, the City my client want to extend the improvement longer form the original scope of work. I am already completed the alignment and road profile centerline and the production plan is 100% completed.
What I need to do is to change and extend the alignment 750 feet backward from the original station (10+00). If I could explain correctly, I want to start the station @ 7+50 (backward from 10+00) and no changes on forward stationing.
What is the best way without doing re-creating alignment.
Looking for a way to label two station on one alignment in a construction note.
Civil 3D 2013 (SP1)
Dell T3500
Win 7 Pro X64
Intel Xeon 3.2 GHz
24 GB ram
NVIDIA Quadro 4000
where to change the default beginning station from 0+00 to 1+00 in my civil 3d profile template (dwt), so that the beginning station is always 1+00, unless the user changes it.
View 3 Replies View RelatedI am trying to find a way to offset points along an alignment showing station, offset and description. This is for a plan and profile sheet see attached example clouded in red.
View 2 Replies View RelatedIs there anyway to display Alignment Station Offset Label at Profile View because sometimes i want to display where is the phisical noze location in profile view also my attached file display what i have in my label and how display my label in profile view.
View 7 Replies View RelatedI need to produce a better standard table for our company, but need to know how it would be possible to display only either the START STAKE VALUE/ STATION or END STAKE VALUE/STATION in the appropriate column. If I can achieve this i would not need to details for straight segments as indicated in the details column.
View 5 Replies View RelatedI have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.
To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.
I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?
I am labeling station and offsets from my alignment for curb returns and such and for some reason if the offset point is directly perpendicular from an alignment PC or PT the label can't find the alignment information. It's like there is a blind spot.
View 4 Replies View RelatedI am trying to edit labels for a particular alignment. All labels are along the same alignment and use the same alignment style. I need to change "defl." in each of those labels to "defl:". So simply changing the period to a colon. But it is a lot of work to go through each label and then in edit label text and then change it. Plus, I have to do this on 12 sheets. That's like 300 labels! Is there a quick way to achieve this. If it were simple mtext or dtext then I could use the find and replace option, but these are civil 3d alignment station offset labels? Is there a lisp that can accomplish this task? I am using Civil 3D 2010.
View 3 Replies View Related