I want to generate Civil 3D point of intersection alignment report including following columes.
PI Row station
Delta Angle
PI Includead Angle
Is this possible?
AutoCAD Civil 3D 2012 SP 2
Is there a way to included the radial bearings of curves for alignment reports generated for the report manager? I know the curves are tangent because I made them so, but the guy checking my report for errors doesn't know that. I don't know any xml.
View 1 Replies View RelatedI am trying to export an Alignment PI Station Report. I've set all the settings I can find to round coordinates to 4 decimal places, Distance to 2 decimal places, and Direction to the nearest second (DMS). When I execute the PI Station Report, the Distance is 3 decimal places and the Direction is to the nearest 100th of a second. how to get these to the correct decimal place? I managed to change them to the correct decimal place for a Station & Curve Report, but not for the PI Station Report. Also, for the Northing/Easting coordinates, I want to remove the commas (for example, a Northing of 3,058,715.3774' should read 3058715.3774').
View 4 Replies View RelatedThe street is a 'T'. The alignment is extended... Sta 0+00 starts 100' back and the intersection at centerlines starts at 1+00. The alignment is masked between 0+00 and 1+00, but that obviously doesn't make a difference for the intersection wizard.
The intersection wizard does not give me a choice, it just presumes a 4-way intersection. How do a do/choose a 3-way 'T' intersection in this case?
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013
Nothing appears as the “Stakeout Alignment Report” is executed,I wanted to execute the “Stakeout Alignment Report” (attached) but nothing appears! This is despite the fact that:
-The IE is set as default browser (attached)
-The Active X is enabled (attached)
I have a 2 mile alignment of a railroad loop track and I am looking to generate a report that include both information at 50' increments and the curve data, i.e. PI, PT, so I can generate a staking report for the surveyors. I noticed that there are pre-canned reports that handle one or the other but not both.
View 2 Replies View Relatedi found a way to get a report of my cogo points relative to an alignment i.e. station offset. problem is, i have thousands of points in my drawing. is there a way to get only a few, or a group of points to show up on the report instead of ALL of them?
View 1 Replies View RelatedHow to label the intersection of the alignments for 3D 2012. This command will label the station equation between alignments automatically.
View 1 Replies View RelatedI am trying to use the Station Offset to Points report from the Reports manager. Currently, as far as I ca see, there is no way to select a group of points to include, either by point group or selection from the drawing. There is only "Select All' or "Deselect All". I want a report that will show the station, offset, raw or full description and elevation of a group of points related to an alignment/street. I don't see that option.
View 2 Replies View RelatedI would like to modified the existing pointlist.xsl.
I would like to use a different font and adjust the text heights smaller, like a 8 pt. for the points, 12 pt for the heading and 6 pt for report data.
I do not see any text size in the file, so how do change these.
Also are there any other point list report available?
Say I'm projecting some 3D polylines to a profile view I have, and the 3D polylines cross the alignment defining the profile view. Is there a way to format the projections such that the point of intersection is identified, and that the points will be updated if I change either the alignment or the 3D polylines?
View 1 Replies View RelatedI am a fairly new user to C3D so this may seem simple.
Can I insert a point on an alignment at a particular Station?
C3D 2010..I have a alignemnt that I need to move the starting point 120' east of where it is now.
I've treid a slew of thing to no avail. Can this be easily done?I already have existing profiles for the current alignment.
How to create an alignment label expression for Geometry Point that will show the delta angle rather than the instantaneous direction or perpendicular direction?
View 1 Replies View RelatedLand desktop anchored the alignment stationing at the "+" sign directly on the alignment.
Is there a way to do the same in C3D 2010 without adjusting the x,y locations?
I am trying to create an intersection design using the Intersection Tools in C3D 2012. I followed the steps in the tutorials, created a corridor on the major road, splitted the regions, created the intersection and added it to the major road corridor, and connect the regions with the intersection portion.
I used the same assembly throughout the design just for simplicity, however, i notice that there are gaps of curb between the curb return section and the through section (as outline in red rectangles).
I have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.
To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.
I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?
I know this. I am aware. This is why I avoid changing the reference point as much as possible if I have profile views or anything else dependent on my alignment. I also have no problem with this dialog giving me a useful reminder.
My problem is this: if I want to make my alignment longer, and I grab the grip at the end of it and drag it to a new location, the reference point moves too! Who in their right mind would want the reference point to move when adjusting the end? Personally I wouldn't want C3D to ever move my reference point automatically. I can have some sympathy with moving it if I am grip-editing the start of the alignment, or the tangent on which the reference point resides. But I'm editing at the end of the alignment, on a different tangent. Why would you move my reference point and make me have to go back and reset it to where it was? How dare you throw your warning message at me for moving the reference point back to where it should be when you secretly moved it to a wrong location with no warning whatsoever?
how to match up certain points. I have imported 2 point clouds and have tried to use the 'align' tool to specify three points from the source object (cloud) and three points from the destination object (cloud). When doing this, it does not properly align them. The point cloud makes it difficult to select the exact point I would like to align, since there may not be a point at that exact location, but close to it. Does AutoCAD require the points in alignment to match up perfectly or is it capable of doing a best fit?
Also, is AutoCAD capable of creating a solid 3D piece from the point cloud? I would like to take all of my points and make a smooth object.
When I check with DIST command both the ends of the line are with distance 0.00000000 to the region. But when I apply intersectwith method to them I get only 1 intersection. This is a sample only, I face this issue regularly.
Private Sub Button31_Click(sender As Object, e As EventArgs) Handles Button31.Click Dim R1 As AcadEntity = Nothing, R2 As AcadEntity = Nothing Ut.GetEntity(R1, "seç") Ut.GetEntity(R2, "seç") Dim inters As Object = R1.IntersectWith(R2, AcExtendOption.acExtendNone) End Subor Dim entMain As Autodesk.AutoCAD.DatabaseServices.Entity = tr.GetObject(id, Autodesk.AutoCAD.DatabaseServices.OpenMode.ForRead) 'Setup 3d plane and point collection Dim myPlaneWCS As Plane = New Plane(New Point3d(0, 0, 0), New Vector3d(0, 0, 1)) Dim myIntPntCol As Point3dCollection = New Point3dCollection() Dim myintptr01 As IntPtr = New IntPtr() Dim myintptr02 As IntPtr = New IntPtr() 'Get intersecting point collection entMain.IntersectWith(ent, Intersect.OnBothOperands, myPlaneWCS, myIntPntCol, myintptr01, myintptr02)
Windows 7 (x64)
AutoCAD 2012 (x64)
Isn't there a command that allows you to pick 2 lines and snap to the point of intersection when dimensioning an object with a fillet/chamfer? Typically I o-track it with apparent intersection with no issues, but its a little more difficult when your working with sloped lines, tracking doesnt like to follow angled lines. (Maybe its inventor that I'm think of that can do this?)
View 3 Replies View RelatedI find intersection of two curves with interop
Dim Zinters As Object = DuvarObj.IntersectWith(MainObj, AcExtendOption.acExtendNone)
then pass the intersection points pt1 and pt2 to managed code to get length of the curve between two intersection points , but I realized that sometimes decimal numbers maybe 10th after comma is different than the curve's start or end points. And so the code below throws error, since point pt1 or pt2 is not exactly on the curve, but they are the intersection points excatly.
What can I do?
Dim dist1 As Double = ent.GetDistanceAtParameter(ent.GetParameterAtPoint(pt1))Dim dist2 As Double = ent.GetDistanceAtParameter(ent.GetParameterAtPoint(pt2))
Windows 7 (x64)
AutoCAD 2012 (x64)
Form Autocad 2000 to 2012, there is always with this problem. It happens sometimes in object snap, it does not work to snap a intersection point (two crossed lines) when drawing a line or arc or others. For sure, these two lines are in the same plan and can be filleted or chamfered. So I turned on the Apparent intersection, it works with apparent intersection point, I am not sure if this apparent intersection will cause other problem. I am working on pure 2-D drawing, do not want to get any 3D objects inside the drawing.
View 3 Replies View RelatedHow do we create dimension at an intersection point between arc and line?see attached picture. I need to create dimension as red line.
View 3 Replies View RelatedI Posted This problem twice but it doesn't showed in the forum. I don't know why, whatever, My problem is making Array with a circle and a line[same as to radius]. When i use array between them to create 9 more lines, some lines are becomes bigger then the original line. why this happen? I attach a file to be understand clearly. Zoom the intersection point of lines and the circle.
View 3 Replies View RelatedIs it possible to select lines (maybe up to 6 lines) around an intersection point with a reference line. There is one intersection point and the lines are around it. And also, both the intersecting lines are in different layers.
How to get the ObjectARX's ArxDbg tool working on autocad 2012. ObjectARX 2010 sample project fails to open in VS2010 express.
I have to create a hole (extrude) in a wall part in my assembly document where a stack will be installed.
To determine where, I verify if a line segment pass through the wall (XY Plane).
But I get an error with the command: IntersectWithLine
Here's my
Public Function IntersectionPoint(ByVal app As Inventor.Application,
ByVal wp As Inventor.WorkPlane) As Inventor.Point
Dim oTransGeom As Inventor.TransientGeometry = app.TransientGeometry
Dim startPoint As Inventor.Point = oTransGeom.CreatePoint(Me.StartVertex.X,
[Code] ......
In assembly mode, how can I click on two lines in a part sketch and get there intersection point using VBA?
View 3 Replies View RelatedI'm attempting to find the intersection point between a LineSegment2d Object and a DrawingCurveSegment object unsuccessfully.
View 1 Replies View RelatedI want to find the intersection point between a cylindrical curve and faces in a body. I have the start point an start vector and a rotational velocity. With this values it should be possible to create this cylindrical curve.
Is there a function in inventor which I can use?
Currently I am using the function "FindUsingRay". But I thing that there is only the possibility to fire a linear function through the body.
Today I found the command "FindUsingVector":
Sub FindUsingVector(OriginPoint As Point, Direction As UnitVector, ObjectTypes As SelectionFilterEnum(), ByRef UseCylinder As [defaultvalue(-1)] Boolean, ByRef ProximityTolerance As [optional] VARIANT, ByRef VisibleObjectsOnly As [defaultvalue(-1)] Boolean, ByRef LocationPoints As [optional] VARIANT,
I did not find any information in the "Autodesk Programming help". what is the difference between this both functions?
Is the argument "UseCylinder" for a switch into cylindrical coordinate system?
i've made a serpantine curve that starts from one line of alignment and end on the other line.
i wanted to know how can c change alignment direction when these two feature line and alignment meet each other in order to change the alignment path?