AutoCAD Architecture :: Rotating Object To Match Angle Of Another
Jul 26, 2012
i would like to rotate an object to match the angle of another. I can measure the angle but there are many decimal points and I want it to be exact.
One method i have employed is to change the ucs - z setting to align with the object to be rotated then click it and select a point that intersects the other object (this case a line) and then the 2nd snap is somewhere along the line.
this works although sometimes i have to rotate a second time 90 deg. or 180 to get proper orientation.
Is there method, or hidden snap?
ACA2011 Win 7
View 5 Replies
ADVERTISEMENT
Oct 5, 2011
Is there a quick way to rotate an object to match an angle without knowing what the angle is? I am using AutoCAD 2011 now. I was using 2007 and I had an add on command the would rotate an object using a base point and picking the two lines that make up the angle, and it would match the angle you wanted. I can not get that command to load in 2011.
View 4 Replies
View Related
Apr 4, 2012
Material mapping.
When I apply a material to a mass element the material follow the world UCS, that's ok with me. But when i rotate the mass element the material map remains with the world UCS but not with the object.
How to lock the material map to the object when I rotate it.
View 5 Replies
View Related
Jul 25, 2012
I have a property line that is N 36d19'52" E but needs to be N 12d52'18" E. The obvious and calculated rotation angle would be 23d27'34" but when I rotate the line by the calculated angle it doesn't rotate to the right angle. It's off by 0d11'10"!? When I draw a line by bearing at N12d52'18" E and inquiry the angle between the property line and the drawn line the angle difference is in fact 23d27'34".
View 1 Replies
View Related
Dec 14, 2013
Is there a quick way of achieving the following:
You have an object rotated at an arbitrary angle
You want to rotate it back to a 90 degree line by snapping it.
I can do this by measuring the arbitrary angle and then rotating it manually based on my measurement.
View 9 Replies
View Related
May 7, 2010
I'm trying to create a dynamic block for plywood. I have the stretch parameter working so that I can stretch the plywood to the needed length. I also have set a rotation parameter based on the various roof pitches that we use. The problem is I would like to be able to rotate the sheathing to a 45 degree angle and then stretch along the 45 degree angle. Once I rotate the sheathing the stretch does not follow the rotation angle. I have attached the file.
View 9 Replies
View Related
Oct 12, 2012
I have created a dynamic block with a rotation parameter&action on an object in the block. My problem is that when I pick the grip to rotate the object it only allows me to rotate it to where my cursor is pointing, if I enter an angle when prompted "Specify rotation angle or [Base point/Undo/eXit]:" say 45degrees the object does not rotate 45 degrees it just rotates to wherever my cursor is pointing
View 9 Replies
View Related
May 22, 2012
How can you dview / twist to get the view twist angle to match a line exact?
I can enter an angle but the angle of my line is not to an exact degree or degree decimal. 2013 Civil 3D
View 7 Replies
View Related
Mar 16, 2011
1. How do I make the angle of the Gizmo appear when I'm rotating the gizmo plane with 'e'?
2. Also, how do I rotate the gizmo itself, so that i can rotate it in any ambiguous axis as well if I wanted to.
For example, let's say I'm slicing a hollowed box usnig Shell modifier. I want to cut the box diagonally. I make the slicing plane vertical using x rotatin axis (red) at perfect 90 degrees (this is why I want to see the angle displacement when rotating a gizmo), then becaue I want to cut it vertically, I rotate the plane on z rotation axis (blue) 45 degrees. Now, I want this cut to be slanted. That means I have to change BOTH x and y axis with equal amount to achieve symmetrical cut I want. ("5 snaps of rotating the slicing plane on x axis and y axis" something like this)
What I want is change the orientation of the gizmo itself so that x or y rotation axis becomes the angle I want the box cut to be slanted at.
3. I've been using 3ds max for rendering most of the time, and didn't really have time to ask myself, why is it such a pain in the a** to get the correct effect I want from max? Viewport and renderd product doesn't match at all for me. Rendering should be just a way of making the viewport image much prettier, not turning garbage into an artwork. Because of the difference between the viewport and renderd image, I constantly have to do test render at 320x240 to see how it looks.
When I say the two doesn't match, it includes but not limited to:
-Lighting Both daylighting system and artificial lights(photometric/standard)
-Intensity
-Shadow casting accuracy
-Material
Scale mismatch of rendering and viewport.
-Color
-I'm guessing it may be because of the lighting that the colors are very off.
-Unexpected glow on my model from other surrounding objects.
Sketchup or Rhino shows vaguely how it's going to look when it's rendered, just poor quality. Why is it so not intuitive in max?
[URL]
View 9 Replies
View Related
Feb 3, 2011
Is it possible to have text that you can rotate in a MVB similar to a dynamic block?
I tried to create a dynamic block within a MVB but doesn't work.
this is connected to the other post about tagging a MVB
View 1 Replies
View Related
Sep 26, 2013
I created a custom door tag I have been using for several years now based on the standard size description (3068). I have always had the constraint set to object so it will be read at 0 or 90 degrees. I am now using ACA2014 and now it puts the tag in at 0, 90, 180 and 270 degrees. how to correct it back so the text is not upside down? I could always set it to zero but I don't like the look.
View 2 Replies
View Related
Dec 21, 2011
We've just upgraded to AutoCAD Architecture 2012 and I discovered that my match properties command (MA) is now on steroids. In the process of making an existing plan into a demo plan, I put a toilet on a demo layer. I intended to use match properties to put other select items on the same demo layer, but when I touched the lavatory, it turned into a toilet. I've never had this happen before. In trying to solve the issue, I've discovered the same thing happens with other AEC objects (couches, urnials, chairs -- all became toilets) and it happens in multiple files. Only walls and doors remain intact with only the layer, color and linetype changing (which is what I was expecting).
I looked at the settings inside the match properties command and none of them seemed to apply. I deselected the special properties options anyway, but the problem remains.
View 4 Replies
View Related
Oct 8, 2012
I am editing a wall. in the roof and floor line edit, I added a gable, now I need to change the slope to match 12/12 pitch. How do I do this?
View 1 Replies
View Related
Jan 11, 2013
I'm working on a drawing which requires me to rotate 3D rectangles until they are leaning against each other like dominos. Because they are standing on a curved path only one top corner of each will touch the adjacent rectangle, and because each one is shorter than the last the point at which they touch is different every time. There are over 40 rectangles.
I have no problem picking the correct axis of rotation for each but I want to avoid time-consuming calculations for the angle of each or the reference Point for each. Ideally I'd like AutoCAD to rotate until it recognizes that the solids are interfering.
Is there a command or a LISP for this?
View 7 Replies
View Related
Nov 17, 2013
I've been using AuroCAD long time ago back in school, and then I moved out to bentlye's microstation after I started working for Jacobs Eng. and now I have to get back to AutoCAD again. My question is how to get the revcloud and text and the revision diamond… and everything to be match with the drawing's size? coz we have stranded in microstation, that’s give you the right size for everything according to the sheet scale.
View 1 Replies
View Related
Jul 19, 2012
just got my boss to agree today to use cad's dimensions instead of the way he's always done it... which is dimensioning everything (everything!) by hand. Clearly that's just nonsense. But what is important is that I make sure these new autocad dimensions look exactly like the ones we do by hand.
I think I've pretty much got the basics down, I just have one major problem: tick orientation. When doing horizontal dimensions, the ticks run from bottom left to upper right. When doing vertical dimensions, they flip. This would drive my boss nuts... to the extent that I doubt I could get him to buy into this if I can't figure out how to keep the ticks running in the same direction.
I understand I could just dimension with no ticks whatsoever, and then just go copy them in by hand, but that reeks of the old, laborious way of dimensioning... and it really seems like there should be an easy answer to always keeping the ticks running the same way.
View 9 Replies
View Related
Jan 30, 2012
I like to think of myself as pretty competent in AutoCAD but I can't figure this one out for the life of me...
I hope I can explain this clearly: When I rotate an object using grips, the object is not shown spinning in real time. I select the object, pick the object's grip, hit <Enter> <Enter> to go into the rotate command and the object will rotate maybe 45^ or so and freeze (visually).
If I use the command line "Rotate" command, the selected object(s) spin in real time or if I use grips to rotate but then use an object snap, it begins to spin in real time for some reason.
I would like to use grips to rotate my objects and be able to see them rotate (like I used to in previous releases).
I have ACAD Civil 3D 2010.
View 5 Replies
View Related
Jun 14, 2012
I went to content browser and loaded the "Plan Elevation Label" onto my tool palette when I go to place the label in the drawing it prompts for elevation and nothing else.
How can you change the rotation on the screen accept to use the rotation command?
The tag itself is referencing a block I went to the block and changed the block now if I go to insert the multi view block it prompts for rotation but not to edit the attribute is there any way to get it to do both?
View 1 Replies
View Related
Nov 14, 2011
untitled.jpg
Is there a way to convert those lines into plines, so i could extrude and cut.
View 6 Replies
View Related
May 14, 2013
How you do the draft angle of, for example, five-star-shaped object in AutoCAD?
[URL]
View 1 Replies
View Related
May 10, 2011
I'm rotating my object using the hotkey combo alt-middle mouse button to view my object as I work. The problem is that the object is not rotating at the gizmo. It makes my workflow turn into a workless flow because it is rotating at the object origin instead.
I'm fairly new to Max and not completely comfortable with all the tools yet.
3D Studio Max 2010 Perpetual
3D Studio Max 2011 Educational 36 Month
Also, I have the same problem with both versions of Max. Obviously some setting that I'm not aware of...
View 1 Replies
View Related
Aug 8, 2013
I need to animate an object rotating around an axis, and moving away from the axis simultaneously.
View 1 Replies
View Related
Sep 7, 2013
How do you set an object's annotation, say a line, to display a line's angle or bearing precision to the nearest 20th second.
Kinda like this for decimals:
0.000
0.00
0.0
But for degrees minutes seconds.
Also, I will require the seconds to hide if the nearest 20th second was a 00. I also need a leading zero for minutes if the minutes was under 10 minutes.
View 2 Replies
View Related
Oct 31, 2012
I am having issues with not being able to put in a column on an angle when using Revit Architecture. I read a troubleshoot guide and you can do it using Revit Structure, however Architecture is a different story.Why is this, and more importantly how can I put a column in on an angle.
View 1 Replies
View Related
Jan 12, 2014
I wanted to know how to rotate an object on a free axis (a line that I create - by two points).
In the image i pointed out the line/axis...
View 2 Replies
View Related
Jan 20, 2012
I'm trying to figure our how to taper a circular object 1-1/2" high on a 45 degree angle from the top down (that is the lower part goes in like a pie pan). Taper doesn't seem to work.
View 2 Replies
View Related
Jun 21, 2011
I want to know if there is a way to make the vertical hatching angle move with the curve of the object being hatched.
In other words how do I/can I stop this ...
View 9 Replies
View Related
Jan 26, 2012
Is it possible to rotate an object along the Y axis as opposed to just rotating in a 2D circle? I know it is possible to simulate 3D rotation, but that takes some tricky maneuvering in some cases. I was wondering if it isn't just a case of holding down a combination of Cntrl & Alt or Shift and dragging a selection point.
I have seen a video where a graphic is created - video is in high speed to show the various steps involved in creating the artwork and there is a section where it looks like the artist/designer rotates a rectangle so that the top left corner appears to be moving "out" of the screen and the right corner towards the "back" of the screen. It doesn't appear to be just a skewing of the object, but in fact it looks like it's in 3D.
View 3 Replies
View Related
May 6, 2013
I have a square object I want to rotate in Illustrator CS6. The object wants to rotate from the center. I want to rotate it from one of the corners. How do I change the reference point from which to rotate around?
View 7 Replies
View Related
Apr 9, 2012
When rotating an object that will put any part of it outside the drawing surface, I get the following error-
Object position specified was not on drawing surface
This was never a problem for me with prior versions of Draw. Is there an option to allow Corel to do so with X6? The only workaround I've found is to temporarily increase the size of the work area, which is a bit of a pain when you're dealing with labels, not just page size.
New information: Just discovered that, if I group all elements, I can rotate them. The bug only occurs if I select (but don't group) them.
View 2 Replies
View Related
Sep 21, 2011
I have never gotten this to work, but had put little effort into it until recently. Thus far I have checked my project standards to make sure "match sheet views to view" is checked to "yes".
In both View drawing and the sheet- VISRETAIN is set to 1.
the VPLAYEROVERRIDESMODE is set to 1
I am working on drawings that are in my current project through project navigator. I am using ACA 2010 and not sure what else I need to do. I turn off all the unwanted layers in the view drawing, then create a sheet and xref in the view to model space- all the layers reset, and I again have to turn off all the unwanted layers. If I change a layer color in the view drawing, it does not change in the sheet drawing upon save and refresh.
I hate wasting time repeating the same task over and over....
View 2 Replies
View Related
