I have a weird issue with Mleader landing lines.In AutoCAD 2012, I get only one arrow grip on mleader landing lines when I select an mleader (see image below) In AutoCAD 2010 - when I open the same exact drawing - I get TWO arrow grips when I select an mleader.
View 2 RepliesI have an mleader with a single vertices point.
There's a thing called a doglength which enables a grip point that allows the leader to be repositioned.
Dim ml As MLeader = TryCast(Entity, MLeader)
ml.SetDatabaseDefaults()
m_leaderIndex = ml.AddLeader()
m_leaderLineIndex = 0
ml.SetDoglegLength(m_leaderLineIndex, 2.5)
I have a problem with the dogleg length in that I can't rotate it according to the current UCS. Is this possible?
what the difference is between the landing and a dogleg of a mleader? What is the difference between the properties:
EnableDogleg
DoglegLength
EnableLanding
LandingGap
In 2010, when you did a multileader, on the landing you had an arrow grip on both ends and then the box grip in the middle.. Now in 2012 they have the landing set to where there is an arrow grip at one end closest to the text and the box grip at the other end....
Is there any way to set the multileader grips on the landing in 2012 the way they were set up in 2010?
I put mleader into a LISP routine and it is doing the text attached to it only in the command line instead of in the drawing is ther a way to put mleader into a LISP routine and have it do the same as when you just type in mleader?
View 2 Replies View RelatedI am trying to use a lisp that will turn on a background mask on selected mleaders. I found the attached lisp here [URL]. it works good except the mask border offset factor is set to 1.5. I need the offset to be 1.0. When I look thru the lisp code it says the default is 1.0 but can be changed.
how I can use the lisp and get mask offset factor to be 1.0?
C3D 2010
3G RAM
XP PRO, SP2
Is there a way to set up a multileader on my tool pallet to automatically pull an xref name when user selects it?
user selects multileader
user selects point on xref
user selects landing location
xref name is inserted as a field
trying to save a few clicks over inserting field
I have had an issue with AutoCAD 2012 that I cannot fix. AutoCAD 2010 did not do this.
Here is the problem: I start by directing your attention to the attached file "LEADER PROB1". As you can see, i have two MLEADER notations. one ("TOP LINE") is above the other ("MIDDLE LINE"). The left side of the text in both mleader notations align and the leader jets out from the left side as well. However, each leader has a different angle at the corner of the leader landing. If I wanted to make the "MIDDLE LINE" leader angel to match the "TOP LINE" Leader angle, i used to move nod where the landing bends and continues on to the leader (circled in red in my attached image).
However, when i move this node, I end up with the angles matching, BUT now the text is not aligned, see attached image "LEADER PROB2".
How can i fix this? Quick Leaders ("QLEADER") works just fine (in regards to landing extensions) but not MLEADERS. I would like to extend the mleader landing but keep the text where it is, I don't want the text portion to move.
How to change MTEXT to MLEADER? We often have texts on our drawing - mostly MTEXT and used line to the text.
Recently I started using MLEADER due to that it has added line to the text and looked more professional with consistent line setting out within the text.
The problem is that I don't seem to find a way of converting MTEXT to MLEADER. From the internet search, it seems that adding a LISP created by someone seems to do trick but I would prefer to do from the Autocad software so that all colleagues can use.
In Autocad 2011, Mleader, is there a way to set the block size and the text size with the source block (square, cercle etc.. I would like to make it a specific size instead of measuring then scaling.
View 2 Replies View RelatedIs there a system variable that controls the MLEADER arrowhead size?
I want to control it with DIMSCALE variable. How to accomplish this task?
AutoCAD 2012 / Inventor 2012
AutoCad 2012 SP1 / Windows 7 64 bit
Sometimes I have MLeader text without Mleaders (ie, I remove the leader arm using MLEADEREDIT). Then when I go to edit this 'floating note', the base point moves:
In this screenshot, I've just finished editing the text. Note that I added in the diagonal line at the current insertion point of the Mleader text (top right):
Then, after I click outside the Mleader box, the text moves:
THis happens only with right-aligned MLeaders, and keeps happening, ie if I edit this text again and close it again, it will move again.
know of a variable which controls how stretching with grips works. I've got a single machine with Autodesk Architecture 2012 that when I select a grip and move it, then type a dimension in the command line, that the line becomes the dimension I typed, not the amount I moved it. For example, If i have 10" line, select and end grip, stretch it +3 inches or -3 inches, the line becomes an absolute of 3 inches. On all other machines, the line would either become 13" or 7".
[URL]
The dynamic input is off.
I have just noticed when attempting to move the attributes in the blocks of my drawing that the grips have disappeared, where they have gone or how to turn them back on?
View 6 Replies View RelatedI use to be able to stretch a line by using the end grip and typing 50 , this would extend the line by 50 units
The problem i now have is that if i do the same thing thing , the line instead of strecting 50 units the line becomes 50 units long in total
is there a system variable that controls this ?
so i select numerous objects and can see their grips. I then go and zoom and/or pan around the place, and the grips disappear!
why is this happening?
Is there a fix?
I am trying to select some portion of my drawing for layer change, but when I panning the view for additional selection, I lost the grips of first selected entities.
View 2 Replies View Relatedwe just upgraded to 2012 and the textmask grips do not show to pick and adjust. they did in 2011 but the only thing when the text is clicked upon there is a gray rectangle without grips in the corners....is the a systen varible to adjust?
View 7 Replies View RelatedIs it possible to get grip points on a circle at 45-dgree increments rather than at 90-degree increments - that is, at 45, 135, 225 & 315 degrees? (Preferably in addition to the 90-180-270-360 grips, but temporarily instead of would work also)
View 9 Replies View RelatedI'm having a small problem in AutoCAD 2012. I can't get any grips on any inserted raster image Cpipping Boundary I try to edit. I can select the edge and the line turns into a dashed line, however no grips. The grips work fine on any vector line. Is there a comand to turn on the grips?
View 6 Replies View RelatedI have a drawing where i am not able to select multiple grips using shift/pick to make the grips "hot". I'm not able to make even one of the grips of a poly line "hot". However, while trying to solve the problem, i've opened another drawing where i AM able to make grips "hot". It doesn't appear to be a system setting issue.
View 6 Replies View Relatedi did the test with a qleader and everything seem to be functional but mealder have an issue where autodesk have to check this
example: i have a layer called test1 with color green i have a meleader with a Dot as an arrowhead when i go to the viewport and change the vport color to red
well everything changes expt the arrowhead which will take the layer color (green) but if i go to properties and i change the arrow head to closedfilled then it will take the vport color (wierd) i did the test with autocad 2008 to 2012 all the same problem
i did tried with a qleader and it works fine.
I have created a dynamic block with a stretch, flip and rotate. Everything works great in its file. When I insert it in another file, the grips move but the block does not change.
AutoCAD 2014
How do I make a leader, no text, no landing, grippers on both ends. Every time I go to grab the gripper on the non-arrow side of the leader it moves away from me . The line just moves away from the pointer at an ever increasing speed and distance).
View 9 Replies View RelatedI just upgraded to AutoCAD Lt 2012. In the settings, I was able to figure out how to automatically get a landing line and how long I want it to be. But! When I draw the leader to left of center, it puts the landing on the left side of the line. How can I turn that auto-directional thing off?
View 4 Replies View RelatedAt a multileader when "automatically include landing" is set to "NO" or unchecked, then a small point (like that at the end of a dimension line) is inserted in the callout block, such as the circle, which then prints. This makes for less than clean drafting to say the least--is this normal? If so, (why?!), is there any way to NOT have those points print/show up?
View 7 Replies View Relatedhow I keep the three risers shown in the image below, but extend the landings on the first and third run to avoid creating the angled corners. The angled corners show up when I manually edit the edges to bring the second run width down to match the first and third run width.
If I extend the landings, it tends to push one of the second run risers around the corner to the third run, and that screws up my design.
Just a quick (but possibly hard?) question. I have a multileader set up, but I also want it to automatically include a line which spans the vertical breadth of the text at the end of the landing. It's hard to explain, so I've put an image below.
Currently it's set up as a block that can change in height, depending on how many levels of text I tell it to fit to. Problem is, if I rescale my Multileader, I'll have to go back and rescale the block separately.
Now, possible to include such a feature in a Multileader such that it autoscales and auto lengthens, depending on the height of text?
how to have an option for the landing direction at the end of a leader line, or a way to edit one that has been created.
View 8 Replies View RelatedI want to force the Multileader landing to go left when the program wants to automatically form it to the right. How can you choose/change the direction of the landing line and side on which the text will be placed.
AutoCAD 2011
I need to know how to eliminate my first tread being part of the landing. I have tried every possible combination of varibles I can find. It happens randomly. when it does if I adjust anything it comes back.
View 4 Replies View Related