AutoCAD 2010 :: 2012 Not Responding Directly After Start Up?
Mar 10, 2012
I have AutoCAD 2012 on a Win 7 64bit laptop. Ive had it on here for over a year and never had this issue till today. My AutoCAD loads up fine and loads up the default Drawing1 file. However after waiting a few seconds and going to click File, it comes up with Not Responding on the top. I wait patiently for several minutes and it does not recover. Not quite sure what went wrong . My desktop has the same issue. There is a possibility of it being caused by CCleaner after using it to fix errors and it messed with something in the resgistry while doing so but not sure.
View 9 Replies
ADVERTISEMENT
Aug 19, 2013
I have a problem that the software is not responding and freezing when creating new drawing or opening another one.
I have windows 7 64 bit Operating system installed on workstation Dell Machine
I look to a lot of discussion and I tried the mentioned ways but still same issue
FYI, this software was working fine with windows XP machine.
View 5 Replies
View Related
Sep 4, 2012
Is it possible to export the contents Table directly into Excell from AutoCad2012?
I've tried the Data extraction wizard but it seems to export the Table attributes/properties and not the contents of the table.
View 4 Replies
View Related
May 15, 2011
I just installed 3DS Max 2012 with a student license, but I encountered a problem that doesn't seem to go away. Whenever I open it, it gets to the "Starting 3DS Max 2012" screen and then freezes. The process freezes as well. Is there a way I can fix this? I have Windows 7 Ultimate, 32-Bit, and a Dual-Core Processor. My computer meets all the System Requirements except an insufficient video card.
View 4 Replies
View Related
Aug 28, 2012
problem when plotting files that have PDF images attached to them and are viewed through a viewport. When plotting, the publishing bar fills up but then stays filled and doesnt disappear. At this point AutoCAD is locked up and I see the file starts spooling. I have several PDF files attached that amount to no more than 500 kb, however, when spooling it racks up to 30mb before in sends it off to the plotter and it takes a very lenghtly wait (up to 60 min). Eventually it plots and sometimes it doesn't plot at all. After a while if I try cancelling the plot, it will start plotting but only half of the page and after that the entire operating system will lockup. We have several machines (6) and 2 plotters in a network and the plotters are shared. Is there a better and faster way to work with PDF xrefs? Could this be a networking problem instead of AutoCAD?
machine specs:
Dell Precision T3400
Intell Core Duo @ 2.33GHz
2GB RAM
OS: XP pro ver.2002 (w/ SP3)
AutoCAD Architecture 2012
Plotters:
HP Design Jet 1055CM
KIP 3000
View 3 Replies
View Related
Aug 30, 2011
I have a drawing that is "Not Responding" when switching from a layout tab to model space by clicking the "Model" tab. I ran a recovery on the drawing and there are no errors. I can't get into model space except by clicking inside my viewport.
View 5 Replies
View Related
Sep 3, 2012
We are using Inventor 2012 and would like to read Solidworks 2012 files directly into the system. This can be done with Solidworks 2011 files but our vendor upgraded his software between the time he sent us test files to try the import and now. Can you tell me if the is a plug in or something that will allow us to read SW 2012 files or should we upgrade to Inventor 2013?
View 6 Replies
View Related
Oct 4, 2011
I just started using Inventor and it is very slow, freezes for a few seconds, and is non responsive. My AutoCAD Architecture 2012 works just fine.
View 6 Replies
View Related
Apr 9, 2012
I'm running AutoCad 2012 in Windows 7 64bit. Notebook is an Asus N53SV, i7 2GHz with 6gb RAM and NVidia Gt540 2gb. The problem is, when i try to Extrude objects, the screen turns into black for a second and a warning says GPU is not responding. Also the notebook has another GPU of Intel within the CPU.
View 2 Replies
View Related
Jan 22, 2013
I am a middle school teacher with a lab of 25 Dell Precision T1600 desktops. I just installed Inventor on all the computers and it works beautifully on 24 of them. On one of them, when you choose the "start" menu, nothing happens. If you click a second time, the area where the menu should be is black and the program stops working. The computers are running Windows 7 and with it working on 24 not sure why it wouldn't work on the 25th.
I have reinstalled 3 times, but nothing seems to work.
View 1 Replies
View Related
Feb 22, 2012
AutoCAD has been working on my laptop for many months. All of a sudden when I start AutoCAD and do the "open" or "new" command, the software says "not responding". If I set variable "FILEDIA" to 0 it prompts me for the file name. I have tried to repair, uninstall and reinstall the software and it does the same thing.
View 9 Replies
View Related
Oct 15, 2011
I am running acad lt 2012 on windows 7- at acad startup I am receiving a fatal error message
"unhandled access violation reading 0x008 exception at 4135104h"
Windows updates are all current.
View 1 Replies
View Related
Mar 29, 2012
Is this supported by Autodesk, and will installing both products create any issues?
View 3 Replies
View Related
Jul 20, 2011
Autocad failes when i tried to directly opening a file from recieved attachment email. whereas it opens it properly when i save the files to hard disk drive.
View 4 Replies
View Related
May 16, 2012
I have just loaded the student version of AutoCAD 2012 onto my brand new HP Pavilion Notebook which has 8 GB of memory - Processor AMD A8-3530MX with HP Graphics 1.90 GHz - running Windows 7 Home Premium 64-bit.
I have created a file in Adobe Illustrator which I converted to a vector image and exported it to AutoCAD. I have loaded the image and have cleaned it up. I am now trying to re-scale it and my session keeps freezing. When I look at the task manager I see that the program is not responding. I have ended the task many times now!
View 4 Replies
View Related
Mar 30, 2009
Haven't figured out the trigger yet but after working in INV for a little while the "Application Menu" (used to be the File menu) does not respond to clicking on any buttons..Flyouts work but when you press the actual button nothing happens..
All other ribbon bar buttons function properly. Simply closing INV and restarting fixes the problem temporarily.
View 9 Replies
View Related
Mar 22, 2011
keep getting program not responding message when I try to open a drawing.
View 9 Replies
View Related
Jun 3, 2013
I can't start smoke neither 2013 nor 2012.
The Console get me this message:
Jun 03 10:16:12 : WARNING: Unable to run with vref
Jun 03 10:16:12 : Effective User ID not 0 (root) !
Jun 03 10:16:12 : Aborting....
Jun 03 10:16:12 : Effective User ID not 0 (root) !
Jun 03 10:16:12 : Aborting....
Jun 03 10:16:12 :
View 2 Replies
View Related
Jul 1, 2012
I'm doing a program in Visual Basic 2010. In one of the forms I put a button that when clicked must open AutoCAD 2012 and make a drawing in it. The user will decide where to save it.The steps are these:
1. I added the references Autodesk.AutoCAD.Interop and Autodesk.AutoCAD.Interop.Common to the Visual Basic Project. That's OK.
2. I wrote this in the heading of the form's
- Imports Autodesk.AutoCAD.Interop
-Imports Autodesk.AutoCAD.Interop.Common
3. In the event Click of the Button1 I put this:
Dim acadApp As New AcadApplication 'Create an instance of an AutoCAD Application
AcadApp.Application.Visible = True 'Show the instance of the AutoCAD Application
Dim acadDoc As AcadDocument 'Create an intance of an AutoCAD Document
acadDoc = acadApp.Documents.Open("C:Respaldo TesisDibujo2.dwg") 'Open a Document called Dibujo 2
'Draw a line
Dim PT1(2) As Double
[code].....
View 2 Replies
View Related
May 23, 2012
I recently loaded several versions of AutoCAD on to a Windows 7 machine. ALL versions will open a drawing if double-clicked from windows explorer, but if I try to open through AutoCAD, the program freezes as soon as I click on the "Open" button. This is true for AutoCAD 2010 through 2012.
Machine Specs:
Dell Optiplex 990
250GB HD
8GB Ram
I7-2600 proc
AMD Radeon HD 6670 (1Gb) Video Card
I also cannot open multiple instances of ANY version of AutoCAD in Windows 7.
View 3 Replies
View Related
Feb 9, 2011
After installing autocad 2011 on one of our users workstation. we try to launch it and it crashes will opening.
View 9 Replies
View Related
Apr 21, 2012
I recently just installed Autocad 2012, using a student licence obtained from the autodesk website. I entered my serial number and product key, and it said that it was suceesfully installed. It even launched, however now when I launch Autocad 2012 the start up screen appears, it says its initialzing, it loads then nothing appears on my screen or even my taskbar, I'm running Windows 7 professional 32 bit.
View 9 Replies
View Related
Mar 13, 2012
Just last week I was working just fine. When trying to access the product today, as usual the A5 sized "Loading" starts but when the product is to appear it just shuts off. It is not indicating what the error is through a dialog box, hence, I am not sure what the problem may be.
I have check various discussion groups which say it may arise from FLEX related files or CascadeInfo.cas but nothing changed. I have also done an entire un installation of the product and Installed it from scratch. The problem persists.
PC Specs:
Intel Core i7-720QM processor
Windows 7 Home Premium N 64-bit
16GB DDR3
1280GB HDD
View 1 Replies
View Related
Oct 2, 2012
I'm having a constant problem with Autocad 2010LT crashing on startup. After clicking on the AutocadLT 2010 icon the program starts to run, I see the start-up screen, and then everything disappears without any notice or error message.
I have installed service Updates 1 and 2 as well as the "Startup Error and Text Editing Hotfix". Nothing that I have read on the forums seems to fix the problem. I'm running Windows 7 Professional (64-bit). I should also mention that I have been running this version of the software on this computer without any issues for over 1 year before encoutering this problem.
View 3 Replies
View Related
Oct 29, 2013
I know that I can find which points are which by checking the properties, but I am wondering if there is a way to (for example) edit the grips so that they indicate which end is which, like how they are used in dynamic blocks to show how an object can stretch. This isn't a problem that requires an imeediate fix, but would be nice if there were such an option.
View 4 Replies
View Related
Jun 22, 2012
I created a linetype using text shape. Let’s say, that my line is only AAAAAA. Now when I apply this linetype in the drawing, the lines always have a small, line before and after the characters. Actually you see this: -AAAA- . How can I delete or hide the start and end lines.
View 2 Replies
View Related
Apr 20, 2012
Autocad 2010 won't start up on my new windows 7 64bit system. I keep getting error msg Error msg : 0XC0000076 when I try to lauch the program
View 1 Replies
View Related
Apr 18, 2012
I have configured a client workspace with a customised quick access toolbar and I am using acaddoc.lsp to ensure it is loaded when ACAD is fired up, the problem is, despite forcing the GUI to change wksps by:
(command "wscurrent" "Autocad classic")
(princ)
(command "wscurrent" "Barclays Net 2012")
(princ)
I can see the swap happening but the quick access bar is missing. If I manually select the current wksp from the switching tool it appears I don't even need to change to a different wksp and on restart it remains visible, it is only occurring on first use.
View 1 Replies
View Related
Jul 24, 2012
I can not get certain linetypes to start with the same dash length, see attached. The linetype will start with a longer dash then the stated length, depending on the length of the pline segment. Is there a way to fix this?
Here is the code for one of the linetypes highlighted:
*FENCELINEc,EX FENCE X---X---X---X---X---X---X--
A,.125,-.0625,.125,-.0625,.125,-.0625,.125,-.125,[FENCEx,FENCEx.shx,x=-.025,s=.1],-.0625
View 4 Replies
View Related
Oct 13, 2013
I try to start msaccess in runtime mode, but an .accdr will not start.this is the code try to use, without /runtime in the code the .mdb and .accdb works great
(startapp "C:\Program Files (x86)\Microsoft Office\Office14\MSACCESS.EXE" /runtime path)
View 9 Replies
View Related
Mar 18, 2013
I have been having problems with Autocad 2012 (running on Windows 7/64bit) where it keeps getting hung up and I get the spinning wheel and the (not responding) message... I notice this happens most often when I am editing attributes of a block, editing text (by double click or through the properties window), or printing to PDF. I am unable to shut down autocad, Windows 7 will not let me end the process in the task manager, and I have to shut off the power on my laptop to force it to shut down. On the few occasions where I got the window to close, Autocad would not re-open, the start up screen would just get stuck at Initializing..
View 4 Replies
View Related
