I am using CAD LT 2005 but also have access to AutoCAD 2005.
I am unsure about the best way of dealing with text in drawings. Originally I used to put my text in model space - which was fine until I started using multiple layouts in paperspace at different scales. The text would come out either to big or too small.
Others in my office say they put the text in paperspace ONLY at the right scale for that layout. This is fine until you realize that if you have to put text in 4 different layouts at 4 different scales 4 different times it takes forever.
So - I looked up about a command called SPACETRANS which seems to offer a way of working out the right scale for the text in paperspace. EG. Working in mm in model space a good text height for me was 1000. By using the spacetrans command in paperspace I worked out that the text height to be used here was 9.2. This basically gave me my text in paperspace at the relatively same height as it looked in model space.
I now realize that although I can scale my text happily to the right size in all my layouts it hasn't negated the need for me to type it all in many times over. Basically, I still have to type the text into paperspace at the right scale - in this example at 9.2.
How you can type your text in once anywhere (probably model space) and then scale it in all the different viewports without having to retype it all in?
Modifying the point size/text size assigned at particular annotation scale,
I’m wondering how the point size/text size assigned at particular annotation scale can be modified.
For example, in the attached screenshot, the point size assigned at the annotation scale of 1/1000 is big and I wanted to make it a bit smaller at that scale.
Viewport. I have scaled the viewport to 1/16 in paperspace, but the drawing is to large and does not fit in the viewport I need to zoom in to make it fit.
Is there a way to have VARIABLE text size AND BLOCK SIZE autocad 2012, for different scales sizes? To sum it up I am running 1/8th scale on some of the pages in the set with a 1/4 blow up section. I use addressable devices so it is a lot of work to change all the text Is there anything that will auto-update the text size per scale with out having to go through my drawing and repeat all the text and VPfreeze it?
In paperspace I set the viewport scale to 1-1/2"=1'-0" on a ANSI D-size plot. But when plotted at (layout) 1:1, it comes out to be 1/8"=1'-0" on a engineering scale.
Modeling 1:1 in MS, dimensioning in PS different scaled viewports. Plotted from PS, did further work both in MS/PS and notice dimension readings have scaled up by 99.98% and 100% to what they were in hard copy. Changed dims in properties but for some reason they have reverted back to the percentage increase? For example I have a 5745mm truss span that is now a 574.5 meter spanning truss!!?? Haven’t altered dimstyle at all or any scalings. Laid another dimension again in PS along side the exaggerated one using same endpoints in order to check things and it’s fine.
Would like to know what has caused the dims to scale up in PS and, how to undo the problem, hoping not to have to re-dimension.
Attached is the dwg. and yes, I have dimensioned in MS but there was a reason. It’s PS that’s causing the grief.
How I set Linetype scale for 3 paper space with different page setup with in single drawing.
Explanation:I have a drawing with XRef attached, I want to make 3 paper space for this drawing with different page setup A0, A1 and A3. I am confused how I set line type scale for each paper space.
In modelspace, architectural schematic plans sections elevations which, when viewported into paperspace drawings, are scaled to 1:100. I therefore work in modelspace with Current object scale = 1, global scale factor = 100. This makes dashed lines etc reproduce at legible scale in a drawing at 1:100.
What about when I move on to details, which in paperspace are scaled to 1:5? At present I start a new file with Current object scale = 1, global scale factor = 5. This makes dashed lines etc reproduce at legible scale in a drawing at 1:5.
Isn't there a way to achieve this, while keeping both the schematic and the detail drawings in modelspace on the same, single file?
Even the above system fails when I want to scale one elevation of the schematics at 1:50, or foundation details at 1:10.
Any way to get a scale bar/title block text to reflect plotting at half size?
We use the common (24x36) sheet size for all projects, but when plotting we send out half size (12x18) as well. This means the scale bar reading 1"=40' is no longer correct. It should read 1"=20'. I would like to automate this.
how to setup the paper size in paperspace, I want my template to match the papersize in paperspace. ie I have a metric template and want it to be setup so when I do a preview it looks right?
The color of the paper space outside of the page layout is a gray-white very bright that would not allow the white lines and white letters to be seen. I have looked at the Options dialog to see if that color can be changed, but I could not find the name of that area outside the per layout ( I have my paper layout to black, which is fine, but I do not know how to change the areas outside the paper). This bright color came with AutoCAD 2012.
Im working for a geological firm that use timescales to describe their work (depths at times etc). I need to compress the time bar but not alter the text but cant find way to do it. Im only scaling in 1 direction.
A file created over a year ago (I believe with AutoCAD 2010) is needing to be updated. I have AutoCAD 2012 and when I open it there is no text in my Paper Space. However, if my manager is to open the same exact file with his AutoCAD 2012 he can clearly see all of the text is still in place. Is there a setting somewhere that I have missed that may be making the text not show up? All layers are on and visible.
I'm having trouble plotting text with blocks in paper space... I can bring up and edit the text within the blocks themselves just fine. I revise the text, hit "ok" and nothing shows where it is supposed to within the paper space.
I have this strange situation.. i use the Arial font inside my cad drawings and when i print my paperspace layout, the text inside the viewport is a little bit more "bold" then the text i put directly on paper space.
Maybe it's a trick to know what text is placed where, but i want all this to be uniform, same thickness. Is there a system variable to correct that issue?
See the image below: It's a 400 DPI scan from an impression i did.
Up to COUPE C1 is the text inside the viewport, under COUPE C1is the paperspace text. Both are the same height... but difference tickness.
I am having trouble with getting certain pieces of text to show up in my viewport in paperspace. There is text and linework on the same layer. However, only the linework shows up in paperspace, not the text. I have seen this before and don't remember how to fix it. It is a setting somewhere but I don't remember where.
why the text and leaders placed over viewports (in paperspace) keeps disappearing? The text is still there...just not visible. i can select the text with no problem. and if i move it off of the viewport then i can see it just fine. this is happening with all the viewports in my drawings... on all tabs. If i close the drawing and reopen then all the text appears again.....but when i switch tabs then come back...the text vanishes again.
I've trying to track down a solution for an issue that we are experiencing. When some of our lisp programs get run, you can no longer double click on text to edit it in paper space. If I put text in model space, I am able to double click to edit it. Is there a variable for this?
I just verified something else, if I move the text to be outside of the View Port, I can double click to edit the text. If I try to double click to edit while inside the viewport then it switchs to model space withing the viewport.
I've tried using the new scale bar in Map 2013. But when I try to insert it inton my map, the size of the scale bar makes it huge, it's way bigger than the layout. How do I decrease the size of the scale bar?
I have created a new point style in a new drawing that I am not familiar with. When I am in model space the points are HUGE, when I am in paper space they are the 2mm that I want them to be.
I think there was a scale setup somewhere but I cannot seem to figure it out again.
I made the mistake that I came to measure my object as cm but inventor writes it's in as mm, is there a way where I can scale objectet up giving it the right size
I've just recently changed jobs and so I'm working on a new (to me) system with Autocad Mechanical 2013. I had been working with Mechanical 2010.
One (of the many) issues that is bothering me, is that I can't seem to scale resize individual dimension. Normally, I'd create the dimensions and then if I needed to tweak the fit, I'd go into the Properties pallet and change the overall scale under Fit. Not really a good standard of practice, I know...
But when I do that on my current system, the dimension doesn't change at all.
On top of that, I have a weird refresh problem. If I grab a dim by the grip and move/stretch it, it doesn't actually show the new position unless I Regen. Is that a setting or maybe just a slow reaction by my computer?
I'm drawing something much larger than the paper so I would like to chose paper size A(8.5x11) set the scale then print it out on A(8.5x11) paper. For example: my desk is approximately 65inch x 30inch and I want to draw and print it on A(8.5x11) paper. I want it to print with the drawing being accurate to scale...how do I do this?
I can control the size of my main drawing views using ilogic based on the models extents as there is a direct relationship between a parts length and the drawing view width. however, I have several isometric views that I scale according to the model size but in certain configurations of my model the ISO’s are completely the wrong scale for that particular view where the main views are ok.
I have a set area on my drawing sheet for the iso view and it would be more beneficial to control the size of the view rather than the scale of the view. I can read the height and width of a view so why can’t I control the size of a view but the height or width?
how to scale life size models in AUTOCAD. I know that a draft should be in a 1:1 scale but lets say I want to draw a plane with exact dimensions measuring the wingspans. How would I set my limits in the command prompt to a specified area. I just don't quite understand the concept of how to calculate an accurate scale then plot the scale with a visible text/title scale upon printing.
I set up a new page thus (I live in a country which uses metric units, so ...):
Drawing Units Setting18-07-2013 9-24-06 AM.jpg
Then:
Command: '_limits Reset Model space limits: Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0.00,0.00 Specify upper right corner <3.5000,2.7000>: 3.65,2.74 Command: C CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 1000,1000 Specify radius of circle or [Diameter]: 250 Command:
and I get:
Range Problem 18-07-2013 9-36-57 AM.jpg
The circle was centred at x=1000 metres, y=1000 metres, yet it displays right down at the bottom left of my screen. Compare the radius of the circle to the distance from the centre to the origin - it's nothing like 1:4! Look at the coordinates for the cursor!
Zooming in and zooming out has no effect on the huge dimensions indicated by the coordinates.
I know this must be simple because it is not mentioned in any textbook or tutorial I have been able to find. Authors don't seem to think it is important, but it's driving me nuts! The question is this:
How do I set the page size and grid scale to something sane?
I am pretty sure that this scale problem is at the root of many of the other problems I am having. A14 is doing it's job faithfully but the display is so small that I cannot see what is happening !
I set a border up to be 24"x36" and it appears to be slightly outside the dotted lines for paper space when I x-ref it in. I also noticed on my plots that 3'-0" is measuring close to 3'-1" which means I have screwed something up.
I have the plot settings set to "Extents", "1:1" and I am using the Cute PDF plot driver.
Instead of creating a border that is 24"x36" do I need to create one that is exact to the printable area to make it the right scale? Not sure what the printable area is or how I figure it out though. Lost.
