1.How can I edit the roof in attached dwg to be like in attached jpg?
One option I think it would be to convert it to roof slab.
What is the disadvantage (if any) to convert ia roof to roof slab?
Can I create it in other way ?
2. In section 2, the first floor walls ends in 90 degrees angle at the roof. Can the walls be edited so that the joint line with the roof follow the roof slope?
ACA 2011...what the best way was to add rafter tails to a roof slab. Someone responded (and even attached a dwg) of a way to do it with a curtain wall. I'm not very well versed in curtain walls, though I get around okay with door & window assemblies, and they seem similar, I just don't really know what differentiates them within the program. That aside, any way to create exposed rafter tails more efficiently than arraying mass elements?
View 1 Replies View RelatedI am trying to add a window vent to my roof slab, I'm using autocad architecture 2013.
View 2 Replies View RelatedI am using AutoCad Architecture 2011. In the Style Manager, I created a wall style using a 8"CMU unit plus a 2" insulation board. I have a gable roof slab that intersects with the wall. I want to trim the insulation board along the bottom of the roof slab, and show the CMU above the roof slab.
View 3 Replies View RelatedAfter having a problem projecting my walls to my roof slab (flat roof), which worked fine in previous sessions; and then trying the standard solutions of making sure my walls clean up properly, etc., I determined the problem was actually in that the walls do not like to project to a roof with components. In my last work session, I added a component to my roof. I switched back to a "standard" roof slab, projected the walls, and then switched back again to my roof with components.
View 1 Replies View RelatedI am working on the project with sloping roof. I have drawn beams with slope. however when I am drawing slab with slopes I am not getting this slopes. There is gap between the beams and slab. I have attached screen shot for more information. Also I need to apply loads for this sloped roof.
View 4 Replies View RelatedOur model uses several material types for insulation, mostly rigid variations at this point. The various materials are used in floor, wall and roof systems. Is there a way to create a single schedule that would list insulation quantities across all three system types?
View 2 Replies View RelatedI am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedHow do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View Relatedcreat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedHow to make hip roof turn gable part way up the roof instead of at the bottom (which would be a gable roof).
View 7 Replies View Relatedwhat the roof elevation property relates to and why? Actually, I know that it is the initial insertion point of the roof baseline, but why doesn't it update with grip edited changes in the elevation of the baseline? See the attached file. The three x-lines converge on 0,0,0. The roof elevation is stated as 0. Obviously that property is meaningless. Considering the importance of roof elevations and making them meaningful, you'd think there would be some rhyme or reason to that property.
View 4 Replies View RelatedHow to ascertain the volume of a roof formed in Autocad Architecture?
View 3 Replies View RelatedIm new to autocad and started designing my own house in archictecture 2010.
I've been having a propblem with the roof design at the moment, i am trying to get the gable ends of the roof to stand up on a 90 angle on both sides by editing the edges/faces but every time i do this the roof ends disappear so theres a hole in the sides of the roof and you can see into the house. How to do this so they do not disappear?
I have modeled a simple house. How can I change the color or even show something similar to shingles?
View 1 Replies View RelatedI quickly created a roof and changed the view display to "sketchy". When I show the roof in top view diagonal lines are shown on the sloped surfaces. How do I get rid of them?
View 1 Replies View RelatedI am using 2011 and have created a project for a 2 story structure. I have constructs for each floor, each floor slab and roof slab.
In which construct do I apply the roofline command? I am unsuccessful so far. Does the roof slab need to be in the same construct as the walls?
I am drawing a house with a hip roof. The roof has a overhang with fascia and soffit. What is the best way to construct the components of the roof system. Should the hip roof and the soffit with fascia to be one system or two separate systems?
View 3 Replies View RelatedI have a Material Definition for my Roof Object. I prefer to keep it a Roof Object instead of breaking it into slabs. See Display Properties image for settings. I have Surface Hatch turned on.
Model views show the hatch correctly.
Elevation views show the hatch correctly.
Plan views do not show the surface hatch at all.
How can I get the surface hatch to show in plan? I have tried changing the cut plan height. It seems I am making something more complicated than it should be.
I know that Archtecture uses views differently than the other AutoCAD verticals, but I'd still like to find a solution to this. When I use the 3DCLIP command to create section views of models created in Architecture, the wall and roof objects do not clip correctly. The clipping planes do not create sections of those objects.
Is there a way to get the 3DCLIP command to actually intersect wall and roof objects?
I want to make a steel deck roof with mineral wool insulation on top. My problem is that I don't know how to do the metal deck.
It should be a slab, a roof slab or a structural member? How do I create it? I attached a drawing with how it should be.
i dont know how to make a roof in autocad 2010, what is the basic step?
View 9 Replies View RelatedI am having trouble constructing the roof for a 3d model. I have attached drawings which should allow you to visualise the type of roof I am aiming to construct.
I have had a go at using the box function then using slice to get the solid into the right shape but then I am unable to slice it at an angle as shown by the red dotted line on my attachment.
roof.docx
How to draw a 3D roof in AutoCAD if I provide the elevations in an AutoCAD file?
View 9 Replies View RelatedI am currently drawing some roof tiles for a house in 3d. I moved the tiles to another drawing so i could get my machine to focus on the tiles rather than walls, windows, doors etc. My machine is still lagging hectically. Basically i would like to know is there a way i can perhaps make the roof tiles file smaller or a "block" of it so that my machine can run properly and i can import it into the drawing with the rest of the house. The roof tiles drawing is 40.3mb big. My machine isn't inadequate-hopefully.
I am on a mac running vmware fusion with windows 7 32-bit and when opening editing the roof tiles file my cpu % spikes to roughly 70% then backs quickly down to 50% and will not increase with Autocad not responding-leave it for a bit and it loads but lags a bit when i orbit, copy or whateva then back to not responding.
where I could download, a 3D model of a timber roof frame in .dwg format? The type of frame I'm after is a hip/valley system, similar to the system described in the attached pic, but must also include all of the internal members (i.e. underpurlins, struts, ceiling members etc.)
en5156b0078.gif
Will be using it to train new staff to visualize the members and how the whole structure ties together.
Im trying to draw a garage with an 8/12 roof pitch but I don't even know where to start with the roof. I just got out of autocad 1 but we didn't talk about roofs. It is a 27x25 garage.
View 2 Replies View Relatedplanning consultant has asked me to show the roof pitches on a site plan.
View 9 Replies View RelatedHow do I find the area of sheathing, rather than the flat area of a roof object?
View 4 Replies View RelatedI have drawn up a roof plan and want to section it off in big areas. Is it possible to draw a rectangle 48'x200' and have that shape fill the entire roof as close as possible. Basically i need my roof hatched w/ a 48'x200' rectangle.
View 5 Replies View RelatedI am trying to use AutoCAD 2013 to create a complicated roof. What is the best way to extend 3D solid roof planes and to trim 3d Solid roof planes that intersect each other? I have tried slicing and can't quite get the hang of it!
View 9 Replies View Related