AutoCAD Architecture :: Get 3DCLIP Command To Actually Intersect Wall And Roof Objects?
Nov 5, 2012
I know that Archtecture uses views differently than the other AutoCAD verticals, but I'd still like to find a solution to this. When I use the 3DCLIP command to create section views of models created in Architecture, the wall and roof objects do not clip correctly. The clipping planes do not create sections of those objects.
Is there a way to get the 3DCLIP command to actually intersect wall and roof objects?
View 2 Replies
ADVERTISEMENT
Jun 12, 2012
I am using AutoCad Architecture 2011. In the Style Manager, I created a wall style using a 8"CMU unit plus a 2" insulation board. I have a gable roof slab that intersects with the wall. I want to trim the insulation board along the bottom of the roof slab, and show the CMU above the roof slab.
View 3 Replies
View Related
Feb 15, 2011
I am using 2011 and have created a project for a 2 story structure. I have constructs for each floor, each floor slab and roof slab.
In which construct do I apply the roofline command? I am unsuccessful so far. Does the roof slab need to be in the same construct as the walls?
View 4 Replies
View Related
May 15, 2013
1.How can I edit the roof in attached dwg to be like in attached jpg?
One option I think it would be to convert it to roof slab.
What is the disadvantage (if any) to convert ia roof to roof slab?
Can I create it in other way ?
2. In section 2, the first floor walls ends in 90 degrees angle at the roof. Can the walls be edited so that the joint line with the roof follow the roof slope?
View 6 Replies
View Related
Jan 9, 2012
I'm trying to send a set of drawings for my consultant. They will be using it as a background for their mechanical and electrical drawings and they only need the 2d information. They want to be able to explode them and remove any items they don't need before switching all the layer colours to grey.
When they get the drawings and explode them the doors and walls explode onto the correct layer but the colour of those object and lines are now set to the actual color of the layer rather than colour "bylayer". The line actually take on the colour of the layer in the properties dialogue box. Therefore when they change the colour of the layer to grey the doors remain 'red'.
I would like the doors/walls to stay on their respective layers...AND their colour to be BYLAYER when exploded.
View 7 Replies
View Related
Oct 12, 2012
We are on ACA 2011 and created a ceiling plan. Sent it to a consultant that is on ACA 2013.The file was saved down, but when we try to make a new ceiling or copy an existing grid, we get the following:
Command: _AecCeilingGridAdd.
Command not allowed because drawing contains objects from a newer version of this application.
View 2 Replies
View Related
Jun 3, 2013
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies
View Related
Dec 7, 2011
I'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
View 1 Replies
View Related
Jun 12, 2012
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies
View Related
Apr 14, 2011
I can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
View 1 Replies
View Related
Jan 24, 2013
I keep getting a Revit warning 'Highlighted walls are attached to, but miss, the highlighted targets.' when I try and attach part of a long wall, spanning between gables, to the underside of roof eave. I must emphasise that this happens on a long wall where I have edited the profile to create three step levels each with a roof on them. Parts of this wall do attach to their respective length of roof but others don't. I wonder if this is something to do with the wall's height parameter, which is the same for the whole length of the wall but will have differing distances to the edited profile?
View 1 Replies
View Related
Sep 25, 2013
In the file attached, there's a wall roof window joint showing the following problem: It seems like the window interferes with the joint, so that it isn't right, if the window is not situated higher than the roof slab. In the picture, the joint on the left side is correct, but the ones on the left are incorrect.
View 4 Replies
View Related
Aug 22, 2012
I know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies
View Related
Oct 18, 2012
I am drawing up my house in Revit to get use to the software. I created my house, and now my garage. I selected to create a roof by footprint but when I tried to join the roof to the adjacent wall, the overhang does not follow. I then selected the overhang to join to the adjacent wall but an error pops up: "Part of the roof to be joined misses the target face."
I attached a PDF of the roof.Also, you will notice a line that separates the two walls I joined together. I may separate them but how do I avoid this if I want to make one solid wall?
As for the wall selection, I have vinyl siding and would like to use properties that relate when selecting my exterior walls. I do not see anything regarding that besides wood siding. I thought that should be in my properties when I downloaded and purchased the software.
View 1 Replies
View Related
Aug 24, 2013
how to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
View 6 Replies
View Related
Aug 31, 2012
Exist a way to Attach the top of the wall in a element that is not a floor or roof. I have a wall under a stair and i want to make de top of the with a slope.
View 2 Replies
View Related
Sep 27, 2012
I am trying to get my drawings into revit but I am stuck on getting the basic form of the building in Revit.
Since I am using slanted walls I need to work with a Mass but I can't get the mass look like my idea. The picture I attached is a simple screen capture of Rhino with the outline of the building.
View 1 Replies
View Related
Aug 21, 2012
I have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies
View Related
Jan 1, 2014
Is there a way to get the default wall/roof/floor materials to appear transparent?
View 1 Replies
View Related
Jun 11, 2012
Our model uses several material types for insulation, mostly rigid variations at this point. The various materials are used in floor, wall and roof systems. Is there a way to create a single schedule that would list insulation quantities across all three system types?
View 2 Replies
View Related
Jan 20, 2014
What I am trying to do is to model a roof using Revit Lt so that the roof tiling and battens carry on over the gable wall. Is it possible to add a void profile to the roof slab in order to achieve this or do I need to model a small section of roof to just cover the wall portion?
View 3 Replies
View Related
Sep 5, 2012
How to make hip roof turn gable part way up the roof instead of at the bottom (which would be a gable roof).
View 7 Replies
View Related
Feb 8, 2008
what the roof elevation property relates to and why? Actually, I know that it is the initial insertion point of the roof baseline, but why doesn't it update with grip edited changes in the elevation of the baseline? See the attached file. The three x-lines converge on 0,0,0. The roof elevation is stated as 0. Obviously that property is meaningless. Considering the importance of roof elevations and making them meaningful, you'd think there would be some rhyme or reason to that property.
View 4 Replies
View Related
Nov 9, 2011
How to ascertain the volume of a roof formed in Autocad Architecture?
View 3 Replies
View Related
Mar 21, 2011
Im new to autocad and started designing my own house in archictecture 2010.
I've been having a propblem with the roof design at the moment, i am trying to get the gable ends of the roof to stand up on a 90 angle on both sides by editing the edges/faces but every time i do this the roof ends disappear so theres a hole in the sides of the roof and you can see into the house. How to do this so they do not disappear?
View 1 Replies
View Related
Oct 13, 2011
I need to calculate area of the roof created in 3d autocad 2009 using the command edge mesh.
I cant convert it to solid or anything else. This roof if created using 4 arcs joint together in 3d environment and with command edge mesh.
View 1 Replies
View Related
Feb 28, 2011
I try to make curb return profile without profile view like a intersect command.
I was make curb return alignment but I can not find profile command without profile view.
View 6 Replies
View Related
May 9, 2011
ACA 2011...what the best way was to add rafter tails to a roof slab. Someone responded (and even attached a dwg) of a way to do it with a curtain wall. I'm not very well versed in curtain walls, though I get around okay with door & window assemblies, and they seem similar, I just don't really know what differentiates them within the program. That aside, any way to create exposed rafter tails more efficiently than arraying mass elements?
View 1 Replies
View Related
Jul 27, 2013
I am trying to add a window vent to my roof slab, I'm using autocad architecture 2013.
View 2 Replies
View Related
Jul 27, 2013
I have modeled a simple house. How can I change the color or even show something similar to shingles?
View 1 Replies
View Related
Apr 5, 2012
I am using AutoCAD Architecture 2012.
I built some walls and a roof slab using the wall, door, and roof slab tools in the build section of the ribbon. I drew a section plane and activated live section. The walls and roof did not cut away and they do not show up when i use the sectionplanetoblock command.
Is there a setting I need to change to make the walls and roof susceptible to being cut using the sectionplane command?
View 6 Replies
View Related
