What I am trying to do is to model a roof using Revit Lt so that the roof tiling and battens carry on over the gable wall. Is it possible to add a void profile to the roof slab in order to achieve this or do I need to model a small section of roof to just cover the wall portion?
View 3 RepliesI know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies View RelatedI'm trying to put some corrugated metal on a wall in a small section, but how to do that.
View 9 Replies View RelatedI keep getting a Revit warning 'Highlighted walls are attached to, but miss, the highlighted targets.' when I try and attach part of a long wall, spanning between gables, to the underside of roof eave. I must emphasise that this happens on a long wall where I have edited the profile to create three step levels each with a roof on them. Parts of this wall do attach to their respective length of roof but others don't. I wonder if this is something to do with the wall's height parameter, which is the same for the whole length of the wall but will have differing distances to the edited profile?
View 1 Replies View RelatedIn the file attached, there's a wall roof window joint showing the following problem: It seems like the window interferes with the joint, so that it isn't right, if the window is not situated higher than the roof slab. In the picture, the joint on the left side is correct, but the ones on the left are incorrect.
View 4 Replies View RelatedI am drawing up my house in Revit to get use to the software. I created my house, and now my garage. I selected to create a roof by footprint but when I tried to join the roof to the adjacent wall, the overhang does not follow. I then selected the overhang to join to the adjacent wall but an error pops up: "Part of the roof to be joined misses the target face."
I attached a PDF of the roof.Also, you will notice a line that separates the two walls I joined together. I may separate them but how do I avoid this if I want to make one solid wall?
As for the wall selection, I have vinyl siding and would like to use properties that relate when selecting my exterior walls. I do not see anything regarding that besides wood siding. I thought that should be in my properties when I downloaded and purchased the software.
how to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
Exist a way to Attach the top of the wall in a element that is not a floor or roof. I have a wall under a stair and i want to make de top of the with a slope.
View 2 Replies View RelatedI am trying to get my drawings into revit but I am stuck on getting the basic form of the building in Revit.
Since I am using slanted walls I need to work with a Mass but I can't get the mass look like my idea. The picture I attached is a simple screen capture of Rhino with the outline of the building.
I have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies View RelatedIs there a way to get the default wall/roof/floor materials to appear transparent?
View 1 Replies View RelatedOur model uses several material types for insulation, mostly rigid variations at this point. The various materials are used in floor, wall and roof systems. Is there a way to create a single schedule that would list insulation quantities across all three system types?
View 2 Replies View RelatedI need to trim the section outlined in red, how do I go about doing that?
View 1 Replies View RelatedI am doing a five stories building and when ad the structural column with concrete cast in place material, the representation in plan view does not cover the block hatch of the wall. See attached image. I have read all about structural columns and did not find any solution.
View 5 Replies View RelatedI would like to know whether it is possible (and how) to trim a wall that was generated from mass face to a roof (also generated from face mass) or/and make a horizontal hole in it. The wall itself is not straight or curved, it shifts outwards from the building from base to top (still in an elevation it looks like rectangle).
View 2 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
breaking wall section views ? ie. using the section view tool works very well for a BIM wall type, but how can we cut the section so we don't need to have the view show the entire height, etc of the wall. especially when fitting in representative sections of twenty different wall types/situations on a single sheet ?
View 2 Replies View RelatedI received a Revit file from a client. What may have been purged from the file. When I try to cut a section, I am presented with the choice of a Building Section or a Detail Section. The Wall Section is not available.
How do I get access to the wall sections? These are available as families which could be reinstalled.
How can You align section cuts to a wall or whatever if it has already been replaced?
View 1 Replies View RelatedIs it possible to get the wall fill pattern to show up in plan view but not in a specific section view? I tried the detail levels, Course, medium, fine, and of course the hatch pattern doesn't show up in course, but then the wall components don't show up either.
I am in a section view where i want to show a repeated cmu detail component up the wall as part of a detail, but then the hatch pattern is displayed behind it. I don't want to remove the hatch pattern entirely because I still want it to be displayed in the plan view.
I need to model a wavy wall in Revit. See attached.
Revit 2014
I have made my sections cuts through the floor plans, but when I view them, the walls I have cut through are not poched in to show that there is a solid wall there.
View 1 Replies View RelatedI am working on a building that will have a cornice running along the top of the wall. This is easily handled by a wall sweep. However, at a point along the length of the wall, the wall will have an arch along the top of it. I tried adjusting the profile of the wall, but the parapet (wall sweep) does not conform to the curve of the wall.How would you model a curved wall with a cornice.
View 4 Replies View RelatedI am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedI am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies View RelatedI created a panorama in PTGUI and imported it into LR5 as a tiff file. There is a small area in the upper right corner that is white as the image did not fit the rectangle exactly. I wanted to use the clone/heal tool to replicate a portion of sky to cover that area, but no matter what I do it will not put anything in that area - it just stays white. I was able to do this in version 4.x. What is going on?
View 4 Replies View RelatedHow do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View RelatedWhenever I try to use the Crop Tool, it only stretches out to a small portion of the image and refuses to stretch down any farther.
View 2 Replies View RelatedI am trying to sharpen a small portion of an image and folling the instructions given in the help files, I cannot locate the "Sharpen Tool" in the tool menu. How I can find this asset in Elements 10?
View 2 Replies View Relatedcreat roof with same line on top roof face & roof vertical side face?
View 2 Replies View Relatedi just started seeing the very top portion of the taskbar in full screen mode. It is just a thin line that gives you access to the taskbar without minimizing CS6. I am running Windows 7 64 bit on a loaded PC.
View 2 Replies View Related