I received a Revit file from a client. What may have been purged from the file. When I try to cut a section, I am presented with the choice of a Building Section or a Detail Section. The Wall Section is not available.
How do I get access to the wall sections? These are available as families which could be reinstalled.
breaking wall section views ? ie. using the section view tool works very well for a BIM wall type, but how can we cut the section so we don't need to have the view show the entire height, etc of the wall. especially when fitting in representative sections of twenty different wall types/situations on a single sheet ?
View 2 Replies View RelatedI know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies View RelatedHow can You align section cuts to a wall or whatever if it has already been replaced?
View 1 Replies View RelatedI'm trying to put some corrugated metal on a wall in a small section, but how to do that.
View 9 Replies View RelatedIs it possible to get the wall fill pattern to show up in plan view but not in a specific section view? I tried the detail levels, Course, medium, fine, and of course the hatch pattern doesn't show up in course, but then the wall components don't show up either.
I am in a section view where i want to show a repeated cmu detail component up the wall as part of a detail, but then the hatch pattern is displayed behind it. I don't want to remove the hatch pattern entirely because I still want it to be displayed in the plan view.
What I am trying to do is to model a roof using Revit Lt so that the roof tiling and battens carry on over the gable wall. Is it possible to add a void profile to the roof slab in order to achieve this or do I need to model a small section of roof to just cover the wall portion?
View 3 Replies View RelatedI have made my sections cuts through the floor plans, but when I view them, the walls I have cut through are not poched in to show that there is a solid wall there.
View 1 Replies View RelatedI am creating a fireplace family in Revit Architecture 2012 with wall host (Speciality equipment with Wall host). I selected the template created the family, but in mean time i can't understand the wall is having delete option.(i.e it is released from host). I am surprised to see that in the family type, the wall host is missing.
View 1 Replies View RelatedRevit 2014.
We created floor plans, created actual wall sections. Then we placed countless section markers that Reference Other Views with the SIM text by them. I would expect to go into the roof plan or elevation and see those same section markers. For some reason they do not show in any other view besides the view in which they were placed. The actual wall section markers show up. Just not the ones placed that reference another view.
Same in reverse. Go into elevation, draw a section marker that references other view. I would expect that marker to show in plan. But again no. I have not had this issue in previous versions of Revit. Just so far in 2014 this has been killing me trying to figure it out.
All views are set to Discipline: Coordination, and the original section markers are set to hide on scales courser than 1"=400' so they should show. Visibility graphics has sections turned on. There is nothing that shows with the light bulb.
I have a installation of Revit 2012 (64bit win7) that some times stops drawing dialogs and Revit menu (the big R-button) in front (or something). If I press open, the dialog only pops up if I press somewhere in the revit window, and windows plays that DING-sound (like when you do something you shouldn't do). It feels like a menu draw issue.. The R-button just never displays a menu when I press it. A restart of Revit fixes the problem, but its annoying and we all know Revit doesn't start very quick...
View 1 Replies View RelatedAny way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
draw an interior wall elevation using the Golden Section as a basis for my design. I downloaded the AutoCAD 2012 version and it seems very hard to use.
View 5 Replies View RelatedI have an assembly that contains a basic lane tranisition with a retaining wall next to the road. I have created an alignment for the lane transition to follow but the wall stays in the same place. Shouldn't the wall move with the lane transition? The sub assembly are inserted connecting each other. what am I missing?
View 8 Replies View RelatedI loaded autocad R2013 and went into the .cui dialog box to look for the screen menu section. It used to be under the legacy portion but it's no longer there. I've been looking all around to try and find where it's at.
View 4 Replies View RelatedIs there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View RelatedShort story is I made a wall sconce from scratch but I can't see the symbolic lines in my ceiling plan in the project.
I needed a linear wall sconce for a client presentation based on one of theirs already installed. The manufacturer doesn't provide BIM for this model so I had make my own. I haven't bothered with photometrics. At this point all I need is a placeholder for the ceiling plan and a 3D model for a hidden line view. I used the wall based light fixture family. There was a plane elevation but no apparent parameter so created one and called it 'mounting height'. After about ten minutes of modeling (and over an hour of tedious aligning, dimensioning and locking of the sketches to keep the model from distorting with changes in wall thickness) I opened the ceiling reference level plan and drew some symbolic lines to represent the fixture on the ceiling plan in my project.
Here's what happened.
The symbolic lines for the CPRL (Ceiling plan in the family editor) are also visible in the FPRL. I don't know why this is and there doesn't appear to be a way to hide them in just one plan. I suspect it's because both are at the same height (the reference level.) I tried changing the working plane before drawing the symbol lines to another plane above the reference level and out of its view range but it had no effect. I can still see them in the floor plan.When I loaded it into the project nothing appeared and I got the message about 'no elements are visible because yada yada'. The symbolic lines didn't show up at all. I checked the detail level and that wasn't it. As far as I can tell the view range for the CPRL and the RCP in my project are the same. They don't show up in the project floor plan either. The sconce is visible in 3D views so it's definitely in there. I tried monkeying with the height of the symbolic lines like I stated in part 1. but it had no effect on there visibility. Symbol lines are visible in other families so it can't be an issue with visibility overides.In my project I noticed there's a parameter for the fixture called 'Elevation'. Changing it moved the fixture up and down on the wall. Changing the 'mounting height' parameter in the project had no effect! This parameter worked fine in the family editor. Playing with the 'Elevation' parameter and the cut plane elevation brought the symbolic lines into view. Apparently the symbolic lines are only visible when the cut line is passing through the sconce. Unfortunately my sconce needs to be mounted at 6 ft and my cut plane is at 7'2 to avoid cutting doors and windows. How do get these symbolic lines to display?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I want to turn off a metal stud wall but leave visible the pre-cast wall.
View 5 Replies View Relatedrevit should give a sub category for wall so it easy to on and off using visibility and give different line color in the object style
View 2 Replies View RelatedIt is rather a long time since I captured, edited and burned to DVD on VS10, maybe I have forgotten what to do? I have Windows 7 and have downloaded the patch which successfully allowed me to capture successfully.
However, now that it is time to burn to DVD - I go to 'create disc' and although this takes me through to the next page - I find I don't have the next section after that - i.e. the actual DVD menu's and the bit where I actually render and burn to DVD.
Carole /posting.php?mode=post&f=1&sid=b7aa5a1c253ac00f6d190aa5ce409121#
In any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
View 2 Replies View RelatedI need to model a wavy wall in Revit. See attached.
Revit 2014
Is there a way to slope the bottom of the wall. See attached x sec.
View 2 Replies View RelatedI am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.
