Revit :: How To Get Wall Sweep Set Up In Type / Structure Properties To Wall Profile Has Changed
Apr 12, 2012
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies
ADVERTISEMENT
Dec 19, 2012
I just created a wall sweep on a wall , but I noticed the sweep doesn't adjust to the wall profile, please see the second floor wall in the attached image. Is there anyway to make the sweep adjust to the profile of the wall automatically?
View 2 Replies
View Related
Jul 22, 2013
I'm trying to create a Tiled Skirt (150x150mm) profile or pattern to be used as Wall Sweep. Is there anyway to create this profile as the Family Template: metric profile (wall hosted) only allow me to create a 2D profile.
I would prefer to avoid detail lines or Filled region to get the tiles shown as I need to schedule and quantify this element.
View 1 Replies
View Related
Oct 31, 2013
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
View 1 Replies
View Related
Jul 29, 2011
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies
View Related
Nov 13, 2012
I have applied a material to a wall sweep, but whenever the sweep turns a corner the material flips upside down.Note that the frieze is supposed to be on top.
View 3 Replies
View Related
Dec 21, 2012
Revit 2013 does not have the Wall Sweep panel available from a 3D view.
How do I go about modifying segments?
Specifically, how do I modify the sweep so it wraps both sides and end of the wall?
View 1 Replies
View Related
Jul 3, 2013
I have a wall type that has an embeded sweep for the wall base. My project is set up in two phases, existing and new work. A door has been created in the existing phase, and demoed in the new phase. Where the door has been demolished an infill with the base appears, great! In the new phase I inserted a larger door that cuts the existing walland the entire infiil from the demolished door, but the base still remains. How do I get the new door to cut the base that was created as a result of the infill?
View 1 Replies
View Related
Feb 13, 2006
I have tried 2 methods of generating a parapet cap:
1 - Creating a wall style with the sweep.
2 - Added a host sweep.
The problem is that using either method or a combination of both methods doesn't always work. I still end up with some caps that don't miter correctly even after editing. Sometimes, different intersections will miter and others won't.
View 9 Replies
View Related
Jul 12, 2013
I need to make a sweep along the edge of the wall opening shown in the project, but Revit does not allow me to do it.
View 9 Replies
View Related
Dec 9, 2013
I have a problem with my revit 2013, I have to change one of my walls structure, but as soon as i hit ok the message "Pads can't overlap (but can share edges)" pops up, I cant understand where the problem comes from because I am not changing pads boundary!
View 2 Replies
View Related
Dec 12, 2012
We have a structure model linked into our architectural model, where some structure will be located within the wall. The cut pattern of structure is not always showing on top of (opaque) the wall cut pattern. Sometimes the cut pattern appears transparent with the wall cut pattern running through the structural member.
I tried playing with this in a fresh project with just a C channel in a wall. Sometimes it shows opaque and sometimes transparent depending on the position of the channel in the wall. I would try making the member flat at different elevations and sloped at different elevations and they all had different graphic display behavior. Then I tried duplicating the wall and channel to have two sets to play with simultaneously. Modifying the elevation or slope in one would actually change the graphics of the other, when the other didn't move.
I've tried checking/unchecking the following parameters within the project and family without any effect: structural material, structural, show pre-cut in plan, and always vertical. Not only am I assuming that the structural cut pattern should be opaque over the wall's cut pattern, but I can't even identify what is causing it to change with different elevation/slope settings.
I will attach 2 screenshots. The one titled opaque is the desired effect.
View 2 Replies
View Related
Jul 25, 2013
I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
View 9 Replies
View Related
Dec 4, 2012
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies
View Related
Nov 27, 2011
Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
View 1 Replies
View Related
Dec 18, 2013
We usually run our own calculations for U Values using the BRE Calculator (UK Building Research Establishment).
I just carried out an experiment to check the value that appears in the Revit properties of a wall type (Heat Transfer Coefficient - U) for a given wall build up.
The result in Revit does not seem to correlate with the value that our calculator generates.
I have checked through the conductivity values for the materials (under thermal properties) - and using the exact same values the Revit generated figure is far more optimistic.
For a typical cavity wall construction:
Brick (102mm) @ 0.54 W/mK
Cavity/air gap (40mm)
Insulation (60mm) @ 0.020 W/mK
Block CME (100mm) @ 0.51 W/mK
Plaster (12..5mm) @ 0.51 W/mK
The value that appears in the Wall Properties Dialogue box (greyed out - so I assume it is a calculated value) is 0.1935 W/m2K
Our BRE calculation generates a figure of 0.268 W/m2K.
The insulation manufacturer claims around 0.25 W/m2K for the given wall build up.
how we could have such a discrepency ? All the conductivity values are correct for the materials used in the wall build up.
I am beginning to wonder whethe the value in the Wall Type isn't a U-Value, although the units are consistent with it (W/m2K)
View 6 Replies
View Related
Apr 16, 2013
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
View 3 Replies
View Related
Dec 15, 2010
I have a restroom where the toilets are housed in separate "rooms" divided by full height/full thickness walls. I want the restroom to be scheduled including the area of all of the smaller rooms so I unchecked the wall's room bounding property. However, every time I reopen the project, this property, although unchecked, is back in effect. How can I get the room bounding property (when unchecked) remain the same when I reopen the file from day to day? I made a simpler file to test this, but could not produce the same error.
View 4 Replies
View Related
Dec 7, 2011
I am trying to modify a vertical structural wall in elevation view - change from rectangular shape to trapezoidal (to allow a flat roof to drain to east). Did south wall in one elevation; I chose the wall, and it was outlined in red. I was then able to drag the east vertical edge down by a foot, creating desired slope. I now go to another elevation to modify north wall the same way, but when I choose the wall, it comes up with a blue ball in the center of each edge, with little hash marks on either side, and won't let me modify anything. Also, when I choose the wall outline (with the blue balls), I can't get to wall properties.
View 2 Replies
View Related
Jun 8, 2010
I am trying to make a schedule and I need to schedule walls, and filter by type. But this option is not available in the view properites/filter options in the schedule.
Is it possible to make this happen without creating an additional parameter for filtering? Which would also open up the potential for omissions in the schedule.
View 5 Replies
View Related
Dec 13, 2010
Is there a simple way to change a wall type without deleting the wall and redrawing it in the new style?any time i change the wall type it changes all walls?
View 9 Replies
View Related
Apr 14, 2011
For a very long time I have missed to able to edit profile on a curved wall. It seems so basic and yet it has not been possible. So I was very pleased when it was pronounced that this basic option was finally possible in Revit 2012. Alas it is not. I am so very dissapointed because this is a basic feature wich should have been fixed years ago.
Any simple method to edit profile on a curved wall without having to attach wall top and buttom to invisible layers of floors and roofs ect.
View 3 Replies
View Related
Jul 2, 2008
i drew a curved wall. now when i select it revit doesn't give me the option of an edit profile button as it would with a rectangular/straight.
View 6 Replies
View Related
Jul 11, 2012
In the properties drop down list for wall type selection, most of the different wall type are not showing. Also my elevation carmera is not showing when i click on a new drawing. In a previous drawing all walls selection type is there and the elevation camera. Only when i start a new drawing when wall type and elevation camera is missing. I check the interface to make sure the boxes are check.
View 1 Replies
View Related
Oct 6, 2011
I am having a problem with creating a curtain wall system. After selecting my mass surfaces and choosing "create system" I am unable to change the type of curtain wall system. It just comes up with a regular grid system on the mass, where as before I was able to choose triangles, rhomboids etc under the properties tab. Now however I see nothing except for the current curtain system and recently used files.
I have also created a custom panel which I want to insert into my project but am unable to do so? I have tried loading it into the project, however because of the above problem I am not able to change it to my custom panel system.
View 5 Replies
View Related
Apr 7, 2013
“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
View 3 Replies
View Related
Nov 22, 2012
I need to create a wall the has a profile (in plan view).
View 1 Replies
View Related
May 30, 2013
I'm, trying to update my wall profile so that all of my interior walls have baseboard/molding on them. I've been successful in creating a wall profile with molding, but only on one side. Looks like this in plan view. (Molding is highlighted and only on one side.)So, I first try to update my wall profile like this:
And I either duplicate, or add another sweep to the wall, and make that "Exterior" as to be on the "other" side of the wall.However, after pressing "OK" and "OK" at the wall profile editing box, I get the following error box:
When I click on "Show", I'm shown nothing. When I click on "Enjoin Elements", this same box comes up no matter how many times I click on the "Enjoin Elements" button.
Having problems adding molding to both sides of their interior walls? Am I going about this the right way? Tried to smallify the actual .rvt file, but I can't get it down to an acceptable size for posting here.
View 6 Replies
View Related
Jan 3, 2012
What kind of an instance paramater needs to be implemented in order to account the host wall type in the door schedule?
View 2 Replies
View Related
Aug 11, 2008
Is it possible to use something like a parameter that would allow you to enter a width in the element properties window of the selected wall(s)?
we would like to have a generic wall (outline only) that the width can be changed per wall for layout purposes, then the walls will be selected & changed later to an actual wall with known materials.
View 9 Replies
View Related
Mar 24, 2012
I have a wall tool whose style has a sweep attached, when I added the tool to the palette it drops the sweep. I know this was a wish list item a few years back. Has the feature been added that allows me to add the sweep to the tool so I dont have to manually import and add the sweep in every drawing?
View 2 Replies
View Related
