“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedAny way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedI am trying to get my drawings into revit but I am stuck on getting the basic form of the building in Revit.
Since I am using slanted walls I need to work with a Mass but I can't get the mass look like my idea. The picture I attached is a simple screen capture of Rhino with the outline of the building.
I need to make a sweep along the edge of the wall opening shown in the project, but Revit does not allow me to do it.
View 9 Replies View Relatedi need a lisp that construct line between two lines of wall by selection called (Wall Centerline)
i attach example of what i want assuming that i will often isolate wall layer in the project to facilitate the task.
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI am using the RetainWallVertical subassembly with a created gutter subassembly attached to the wall and a DaylightGeneral subassembly attached to the gutter assembly. My cut slope parameter is set to hold at 1.5:1. I would like to use a target (feature line or alignment) to daylight to and have the wall height adjust accordingly. Problem, I am not able to use a target other than a surface for daylighting. I can use my existing ground surface, which I am daylighting too, but I can't adjust the target point.
View 2 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I have used Autodesk products in the past, but I have never had this much trouble making a single wall. There are no scroll bars to move my view in the blue prints, keyboard arrows don't work, and there appears to be no way to change the cursor type so I can select and drag the viewing area. Is there some trick to it? When I drag the mouse it just highlights everything. This is especially annoying when I am just trying to change the orientation to see what is already made.
I am trying to begin with a very simple project: A deck. All I want to do is draw two original brick walls and then begin with a wood frame construction to place against it, but I also can't even seem to make a single right angle with this. When one wall length is finished it wants to position itself at 15 degre angles, but not in relation to the wall it is connected to. It sets those angles in relation to the compass direction which results in an inability to make even a single square. This means that even though the original wall I am building onto faces a South west 340 degree direction I pretty much have to disregard the presence of a compass and assume North is "top" which is pretty sloppy and makes me question why a compass is even present.
With a north orientation I can get right-angles without any problems, but the mouse is too sensitive and if I type in a length before clicking to create the wall the size ends up much longer than what I define. I can create it, select it, and then define the length, but I can't seem to define which side it expands from and I can't seem to find a toggle to keep a connected wall snapped in place or even to manually move that wall.
Also: When attempting to insert an opening into the wall at a specific point in the wall there appears to be no option to manually define (with text) it's position in that wall. There is a graphical method, but no matter where I put it on that wall it snaps to the far end. It's an existing wall with an existing opening.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
Is there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View RelatedShort story is I made a wall sconce from scratch but I can't see the symbolic lines in my ceiling plan in the project.
I needed a linear wall sconce for a client presentation based on one of theirs already installed. The manufacturer doesn't provide BIM for this model so I had make my own. I haven't bothered with photometrics. At this point all I need is a placeholder for the ceiling plan and a 3D model for a hidden line view. I used the wall based light fixture family. There was a plane elevation but no apparent parameter so created one and called it 'mounting height'. After about ten minutes of modeling (and over an hour of tedious aligning, dimensioning and locking of the sketches to keep the model from distorting with changes in wall thickness) I opened the ceiling reference level plan and drew some symbolic lines to represent the fixture on the ceiling plan in my project.
Here's what happened.
The symbolic lines for the CPRL (Ceiling plan in the family editor) are also visible in the FPRL. I don't know why this is and there doesn't appear to be a way to hide them in just one plan. I suspect it's because both are at the same height (the reference level.) I tried changing the working plane before drawing the symbol lines to another plane above the reference level and out of its view range but it had no effect. I can still see them in the floor plan.When I loaded it into the project nothing appeared and I got the message about 'no elements are visible because yada yada'. The symbolic lines didn't show up at all. I checked the detail level and that wasn't it. As far as I can tell the view range for the CPRL and the RCP in my project are the same. They don't show up in the project floor plan either. The sconce is visible in 3D views so it's definitely in there. I tried monkeying with the height of the symbolic lines like I stated in part 1. but it had no effect on there visibility. Symbol lines are visible in other families so it can't be an issue with visibility overides.In my project I noticed there's a parameter for the fixture called 'Elevation'. Changing it moved the fixture up and down on the wall. Changing the 'mounting height' parameter in the project had no effect! This parameter worked fine in the family editor. Playing with the 'Elevation' parameter and the cut plane elevation brought the symbolic lines into view. Apparently the symbolic lines are only visible when the cut line is passing through the sconce. Unfortunately my sconce needs to be mounted at 6 ft and my cut plane is at 7'2 to avoid cutting doors and windows. How do get these symbolic lines to display?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I want to turn off a metal stud wall but leave visible the pre-cast wall.
View 5 Replies View Relatedrevit should give a sub category for wall so it easy to on and off using visibility and give different line color in the object style
View 2 Replies View RelatedIn any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
View 2 Replies View RelatedI need to model a wavy wall in Revit. See attached.
Revit 2014
Is there a way to slope the bottom of the wall. See attached x sec.
View 2 Replies View RelatedI am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.
how to have different colors for different wall faces? Like all have a plaster finish on the external side, but the colors are different, but when I try to change the color of the external finish, it changes it for all the walls.
View 5 Replies View RelatedI've inserted walls etc in the "Existing" phase.
How do I show them demolished?
In the "New Construction" phase do I need new wall types?
I am trying to change the wall assembly of my foundations (getting rid of a layer of EIFS) and it won't let me delete the layer or change the width (although I can change it into an airbarier). Is there any way to control what parts of the wall are locked in the "edit assembly" window?
I am very new to Revit and am using a student version, I'm nt sure if that changes things.
Cannot insert any window in this wall (its 140mm blockwork single skin trimmed to the roof above) and tried different window families. Yet I can cut an opening and also insert any door.
View 4 Replies View RelatedI can tag walls by entering the wall type in the 'type mark' box in the assembly's properties, but is there a way of listing out the material of each type of wall that has been used in the project. e.g:
Wall Type P1
16mm Gypsum Board
92mm Steel Stud
16mm Gypsum Board
I added base to wall in sweep and I change to interior or exterior in Wrapping at Ends. It does not show any base at end wall. Did I miss anything? How I can make it work?
View 2 Replies View Related