Revit :: Insert Window In Wall
May 9, 2013Cannot insert any window in this wall (its 140mm blockwork single skin trimmed to the roof above) and tried different window families. Yet I can cut an opening and also insert any door.
View 4 Replies
ADVERTISEMENT
Revit :: Can't Put Window In Curved Wall
Mar 6, 2012I can't put my nested window family in a curved wall. Where the problem could be situated? It has to be a normal straight window so I use my nested window families from other projects. I compared my NWF(nested window family) with the ones autodesk provides with revit but I don't find the difference. The NWF from autodesk work in a curved wall.
View 2 Replies View RelatedRevit :: 2014 - Insert Arch Opening In A Wall
May 28, 2013I need to insert a arch opening in a a wall. I dont have a opening folder under my door family. I tried to download openings from revit city but although i save it in my sampels file is is just not there.
View 2 Replies View RelatedRevit :: Wall Roof Window Joint
Sep 25, 2013In the file attached, there's a wall roof window joint showing the following problem: It seems like the window interferes with the joint, so that it isn't right, if the window is not situated higher than the roof slab. In the picture, the joint on the left side is correct, but the ones on the left are incorrect.
View 4 Replies View RelatedRevit :: Window Trim On Curved Wall?
Nov 14, 2013How to add trim or diagonal sweeps to a curved wall. I have a circle top window in a curved wall and I need to add 1x4 trim around it.
View 1 Replies View RelatedRevit :: Voids To Cut Host Wall In Window Family
Feb 16, 2012I would like to cut a void into the wall of a host window family. When I place a void in the family, it does not cut thought the wall.
I tried making the void on a plane perpendicular and parallel to the wall plane. I dont know if this has anything to do with how voids work. But its not working. I also dont have an 'opening' element in the window family.
Revit :: Curtain Wall Convert To Regular Window
Jun 10, 2012I'm working on a small project: a 2 story single house.
There are some curtain walls in the house. Also, a sliding glass door within the curtain wall. I want the same window schedule covers both the regular fixed windows and curtain walls.
Is it better to convert the curtain walls to regular windows? Or there are other better options?
Revit :: Use Parameter To Enter Width In Element Properties Window Of Selected Wall
Aug 11, 2008Is it possible to use something like a parameter that would allow you to enter a width in the element properties window of the selected wall(s)?
we would like to have a generic wall (outline only) that the width can be changed per wall for layout purposes, then the walls will be selected & changed later to an actual wall with known materials.
Revit :: Modify Windows Family - Change Axis Of Insertion Of Window In The Wall
Jul 19, 2012I am working on my first real Revit project. i need to modify a windows family and in particular i want to change the axis of insertion of the window in the wall. I mean... my window should be placed on the outer edge of my wall. i try to unlock the dimensions that define its position and then i lock the dimension in the new position; the window seems to be ok but only in the RFA file. When i imported it in my project file, the windows moves in the wrong way in my real wall.
View 4 Replies View RelatedAutoCAD Architecture :: Wall Style Creation (Window To Cut Only One Portion Of Wall)
Dec 7, 2011I'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
Revit :: How To Place Midpoint Of Window On Midpoint Of Wall
Oct 1, 2012How to place the “midpoint” of window on the midpoint of wall?
In the screenshot below, I wanted to place the window from its midpoint to the midpoint of the wall. How this can be performed on Revit?
Revit :: How To Get Wall Sweep Set Up In Type / Structure Properties To Wall Profile Has Changed
Apr 12, 2012Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedRevit :: Bulkhead Wall Join Skews Bottom Of Existing Wall
Jul 25, 2013I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
Revit :: How To Align Curtain Wall With Edge Of Concrete Slab / Face Of Wood Framed Wall
Dec 4, 2012I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRevit :: How To Cut Red Part Of Wall 1 / Hole In Wall 2 By Blue Rectangle
Nov 27, 2011Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
Revit :: Changing Length Of A Wall And Wall Type?
Oct 31, 2013When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
Revit :: Arched Hole In Wall And Wall Height
Apr 16, 2013I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
Revit :: Adding Wall Sweeps To Wall Profile?
Jul 29, 2011I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedRevit :: Drag Wall End To Edge Of Wall
Apr 7, 2013“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
Revit :: Window Frame Depth Changes When Modifying Window Family
Sep 14, 2013I modified a Window Family file by adding a Window inset parameter. When I inserted the window into a wall, otherwise the window worked fine, but when I changed the window's Window Inset value, the frame depth changed instead of the frame's location. The frame was originally made by Sweep tool, but now when I made it by Extrusion tool, the window works fine. Anyway, for future purposes, I would like to know how to be able to use the Window Inset parameter with a frame made by Sweep tool. How do I lock the depth of the frame sweep?
The file is attached.
AutoCAD Architecture :: Wall Brake At Window
Mar 8, 2013In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View RelatedAutoCAD Architecture :: Window Not Placing In A Wall?
Feb 29, 2012Why would a window not go into a wall?
I have a client who is having this issue - when I open the file it works fine for me.
Is there a system variable or setting that could cause this?
AutoCAD Architecture :: Align Window Within Wall
Mar 22, 2012How to reposition window within wall? i have a window put into my basement wall with footing as shown. unfortunately, the window aligns on the symmetry line of footing itself (as i believe the footing is taken as the overall wall thickness). i want the window to be aligned on the wall/cavity thickness only.
i prefer to have it default in this window or wall style rather than playing around with anchors and other ,,reposition tools'' for each and single window in my basement plan.
AutoCAD Architecture :: Set Window Assembly To Be Flush To Outside Of Wall?
Apr 1, 2011How do I set a Window Assembly to be flush to the outside of a Wall? I'm expecting an embarrassingly simple answer, but I really cannot figure this. the infills and the mullions move out 7-1/16", but the two frame elements just will not be moved.
View 1 Replies View RelatedAutoCAD 2010 :: Example Drawing - Connection Between A Window And Wall
Nov 15, 2012I am looking for an example autocad drawing of the connection between a window and a wall. In other words, a drawing which shows how the window is attached to the wall.
Does not matter what kind of window, materials etc.
AutoCAD 2010 :: Making Window On Finished Wall
Apr 11, 2012I know there is a command for making a hole on a wall or a facade without compromising the finishes on the wall.
eg:i have a wall now drawn out, with all the details of the wall done, but i realise now have to make a window out of the wall i have hatched, but i do not want to create a rec and trim it. as i may have to change the window position again.
AutoCAD Architecture :: Inserting AEC Window And Smart Wall Isn't Trimming
Mar 10, 2010we just recently went from 2008 to 2010 Autocad Architecture. the windows from a 2008 file had the windows in the smart walls and would trim the wall... however, i opened the file in 2010 and all the windows are showing up, but not trimming the smart wall.
View 9 Replies View RelatedAutoCAD Architecture :: Wall Style And Window / Door Insertion
May 3, 2012I use ACA 2012 for residential design - I have a wall style, 2x4 stud w/ 1.5" airspace and 3.5" brick (modified from the stock styles) - but whenever I insert a window, it makes it as wide as the wall (9") when it should be only the depth of the stud wall (2x4 or 2x6) - How can I fix this?
View 7 Replies View RelatedAutoCAD Architecture :: Create A Window That Slides Into Pocket In Wall
Mar 12, 2013Is there a way to create a window that slides into a pocket in a wall the way a pocket door does?
(I'd define a pocket door style for it but I'd like it to appear as a window for tags and schedules.)
AutoCAD Architecture :: Exploding Doors / Window And Wall Objects - Colour
Jan 9, 2012I'm trying to send a set of drawings for my consultant. They will be using it as a background for their mechanical and electrical drawings and they only need the 2d information. They want to be able to explode them and remove any items they don't need before switching all the layer colours to grey.
When they get the drawings and explode them the doors and walls explode onto the correct layer but the colour of those object and lines are now set to the actual color of the layer rather than colour "bylayer". The line actually take on the colour of the layer in the properties dialogue box. Therefore when they change the colour of the layer to grey the doors remain 'red'.
I would like the doors/walls to stay on their respective layers...AND their colour to be BYLAYER when exploded.
AutoCAD Architecture :: 2013 - Accessing Wall / Window And Door Pallet?
Jun 5, 2012In Autocad Architectural 2012 if I typed 'wall' I would get several options for walls. If I selected 'A' (add) it would bring up the properties panel and draw the necessary walls. This does not work in Architectural 2013. Where to I access the wall/window/door pallet?
View 4 Replies View Related