we just recently went from 2008 to 2010 Autocad Architecture. the windows from a 2008 file had the windows in the smart walls and would trim the wall... however, i opened the file in 2010 and all the windows are showing up, but not trimming the smart wall.
View 9 RepliesI am using AutoCad Architecture 2011. In the Style Manager, I created a wall style using a 8"CMU unit plus a 2" insulation board. I have a gable roof slab that intersects with the wall. I want to trim the insulation board along the bottom of the roof slab, and show the CMU above the roof slab.
View 3 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View RelatedWhy would a window not go into a wall?
I have a client who is having this issue - when I open the file it works fine for me.
Is there a system variable or setting that could cause this?
How to reposition window within wall? i have a window put into my basement wall with footing as shown. unfortunately, the window aligns on the symmetry line of footing itself (as i believe the footing is taken as the overall wall thickness). i want the window to be aligned on the wall/cavity thickness only.
i prefer to have it default in this window or wall style rather than playing around with anchors and other ,,reposition tools'' for each and single window in my basement plan.
How do I set a Window Assembly to be flush to the outside of a Wall? I'm expecting an embarrassingly simple answer, but I really cannot figure this. the infills and the mullions move out 7-1/16", but the two frame elements just will not be moved.
View 1 Replies View RelatedI use ACA 2012 for residential design - I have a wall style, 2x4 stud w/ 1.5" airspace and 3.5" brick (modified from the stock styles) - but whenever I insert a window, it makes it as wide as the wall (9") when it should be only the depth of the stud wall (2x4 or 2x6) - How can I fix this?
View 7 Replies View RelatedIs there a way to create a window that slides into a pocket in a wall the way a pocket door does?
(I'd define a pocket door style for it but I'd like it to appear as a window for tags and schedules.)
I'm trying to send a set of drawings for my consultant. They will be using it as a background for their mechanical and electrical drawings and they only need the 2d information. They want to be able to explode them and remove any items they don't need before switching all the layer colours to grey.
When they get the drawings and explode them the doors and walls explode onto the correct layer but the colour of those object and lines are now set to the actual color of the layer rather than colour "bylayer". The line actually take on the colour of the layer in the properties dialogue box. Therefore when they change the colour of the layer to grey the doors remain 'red'.
I would like the doors/walls to stay on their respective layers...AND their colour to be BYLAYER when exploded.
In Autocad Architectural 2012 if I typed 'wall' I would get several options for walls. If I selected 'A' (add) it would bring up the properties panel and draw the necessary walls. This does not work in Architectural 2013. Where to I access the wall/window/door pallet?
View 4 Replies View RelatedI can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
I created a structural member of Pro-Panel II and placed it like a column. This works great, except when I need to trim the excess off at the end of a wall. I tried using a body modifies and it works in model view, but it doesn't in plan view.
View 1 Replies View RelatedWhen I trim or move a block (roof trim mostly) there is an outline of the block I am working on, I know the solution, if you move the block over, it moves but the outline stays where the block used to be, then I copy it back and delete the outline or original block that made the outline and its back to normal.
-Trim BUg02 is my trim after its been trimmed with mysterious outline left over
-Trim Bug03 is my trim after being moved with mysterious outline left in objects original place
I would like to know whether it is possible (and how) to trim a wall that was generated from mass face to a roof (also generated from face mass) or/and make a horizontal hole in it. The wall itself is not straight or curved, it shifts outwards from the building from base to top (still in an elevation it looks like rectangle).
View 2 Replies View RelatedI drew a template of a car and used pastels to colour it in and then i put it back into photoshop and kinda tidied it up a little.
View 4 Replies View RelatedI am looking for an example autocad drawing of the connection between a window and a wall. In other words, a drawing which shows how the window is attached to the wall.
Does not matter what kind of window, materials etc.
I know there is a command for making a hole on a wall or a facade without compromising the finishes on the wall.
eg:i have a wall now drawn out, with all the details of the wall done, but i realise now have to make a window out of the wall i have hatched, but i do not want to create a rec and trim it. as i may have to change the window position again.
I've just upgraded to ACA 2012. I can see how to insert a door in either an offset "or" centered position, but not both. In my previous version, the position could be set to "center / offset" which was an "and / or" option depending on the cursor location. Is this option available in ACA 2012?
View 2 Replies View RelatedWhen I insert a pdf it does not have a white background and it REALLY slows down CAD. I played with the contrast and fade but the image gets worse. The best I can get the image to look is having the contrast set to 100 and the fade set to 0. I have used this pdf in other projects using 2004 and 2007 but with 3013 it is inserting it quite differently.
View 6 Replies View RelatedLast week we upgraded to ACA 2013 from ACA 2012.
I am now having issues any time I try to insert a Block into any drawing - I get a Fatal Error.
I have uninstalled & reinstalled this afternoon but I am still having the same issue.
It happens when I am trying to insert blocks from both the Design Centre & also from Tool palettes.
Other users in my office do not have this problem, the only difference between my set-up & theirs is that I have installed the 'AEC Section Display & Tag Scale Hotfix' but I have tried uninstalling this but had the same results.
When using the design pallette tool bar, my objects will not insert into the selected surface? Reasons Why?
View 2 Replies View RelatedI used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies View RelatedI quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedIn Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies View RelatedI did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies View Relatedhave trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
Is it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 Replies View Related