Is it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 RepliesI can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
I have an area that needs batt insulation show in it that starts at 6" wide and go to 12" wide. Is there a lisp or hatch that auto scales batt insulation in the same manor a poly can do so?
View 9 Replies View RelatedExisting polyline set to a width of 6. Want to fillet this to a non-polyline with a width of zero.
Currently the two lines will join to create a connected polyline but the original widths are maintained (6 and 0).
I am looking for the system variable where the non-polyline becomes joined and the global width for the new segment matches the first polyline.
I am trying to create a custom message box with variable width and height by passing width height title and list of text. I can get the routine to work if I use preset width and height, but would like to make the box adjustable.
Here is what I have so far -
;--dialog box--
MYmessage :dialog{
label="Custom message box";
:column {
:text {
key="MY_message_Title";
fixed_width_font=true;
[code].......
how to make the line smaller in the start, and wider at the end. With a brush, I can only figure out how to draw with the same thickness all the time..
View 8 Replies View RelatedI have a pre-existing graphic uses a stroke with variable with profile (I think) or a special brush to make it look like it's hand drawn. I'd like to apply the same effect to a few new illustrations to keep the style consistent. For whatever reason when I ungroup the graphic and select one of the paths, the stroke weight and variable width profile remain disabled (see pasted toolbar graphic below). The brush still says "Basic" despite the fact that visually it is certainly not the basic brush.
Selected Path
Toolbar (I realize that it says Group instead of Path, but even if I ungroup again and select the path the same options are disabled).
I use Illustrator CS5 and can not blend variable width strokes in Illustrator. I can not do that even with the same width profiles unless they are expanded. I could not find any questions similar on the net regarding this, but wanted to double check before I just made the necessary changes. I'm a bit confused because Adobe 'help' shows how powerful the blends of objects are, but we can't do them as strokes?
I want to keep the blend as strokes not expand them. What is the best way to view how the blend will look with variable widths without expanding and then 'undoing' a bunch of times.
but is there a hot key for expanding the blend without going into object-blend-expand?
Is there a way to change/customize the variable width profile options for the drop-down options next to the Brush definition options?
View 1 Replies View RelatedI've read a couple of methods for deleting variable-width tool points on a path (NOT path points or paths.)
None of them work for me; is there some trick to doing it?
I have read: A) Hover over the unwanted point (with var. width tool) and hit Delete and B)Select unwanted point with var width tool and hit delete.
Both moves result in the entire path being deleted.
I'm trying to change the size of a rectangle wall and I'm looking for "length" and "width" buttons in the properties manager box and can't figure it out. I thought I could just key in the new size after establishing an anchor point.
I've tried lengthen and extend. But the object is a closed polyline and what I'm doing is not working. Not having much luck with the key-grips either.
The wall is 47'2" and I want it to be 46' 8".
I am looking for any info on scripting the Variable width tool (Javascript).
Background: By adding a gradient to a variable width strock you can create nice 3D looking Shapes (see example)
this is a straight vertical line with varied widths, then hit with a gradient.
Goal: My hope is to write a script that will take a "Profile" or "Shape" and convert it to a Variable width line. (see Example)
The Black line is to have its widths modified
The Red line is how wide the line needs to be.
Ive been messing around with the variable width tool, Im not sure I i changed something, I did try to restore defaults but when I make a change it changes the opposite side of the image. For example In screen shot I changed the width on the left and the effect showed up on the right.
I would like the width to change where I change it.
I'm working on a reflective drawing and using gradients on strokes. I've been using pressure sensitive calligraphic brushes I made. Now I'm trying to use variable width preset profile brushes. It works fine for the first stroke, but every time I make a new stroke, it reverts back to a calligraphic pressure brush. How can I keep my brushes the same profile until I manually select it to be different? I've gone back and forth between the brush tool and pencil tool and neither will keep any basic variable width profile past the first stroke. I have to select every brush stroke and change it again and again after drawing it.
View 3 Replies View RelatedI’m using Adobe Illustrator CS6 with a mouse rather than a pressure graphics tablet.
When I create a stroke using the Paint brush tool I would like the stroke to contain a variable width profile. For example narrower at the beginning and end of the stroke but thicker in the middle. Now I can do this by selecting the line after I have made the stroke and choosing the Basic Brush Definition from the drop down list. But if i try to draw a new line the settings are reset again. I cannot create a variable stroke while creating the stroke. The brush definition keeps resetting to 5 pt Round and stroke width 1 pt. It would be much quicker if the stroke remained as a varying width profile as I created the strokes.
I noticed the same problem with the blob brush tool except it's even worse. With the blob brush tool the stroke weight always resets regardless of whether or not I try to set a Variable width profile.
I tried deselecting "New Art has Basic Appearance" mentioned on another forum but that didn't work.
[URL]
Notice the variable width profile is maintained as the artists draws. It doesn’t keep resetting.
I want it to be a variable stroke, so I loaded up “Width Profile 2” in the profiles. The trouble I am having, is that Illustrator defaults to start the larger dots in the bottom right hand corner, and I would like the “starting point” to be in the middle of the line if you know what I mean. I'm still happy for the dots to start big, then gradually decrease in size, but I want to control where the “beginning” is.
View 2 Replies View RelatedIn Illustrator CS6 and CC, when the stroke width tool is used on a curve, the curve is actually made up of a series of straight lines instead of smooth vector curves:
whereas in CS5 it looks perfect.These images may be too small to see the details, but the difference is there. Is there a workaround for this? Or is it recognized as a bug?
what the variable is that turns off the animated zoom all ?
View 3 Replies View RelatedI am finding that if I start with a CommanLine (not full width of the screen) centered on the bottom of the drawing window, as I am working the CommandLine has increased to the full width of the screen.
Why this may be happening or how I may prevent?
Is it possible to use something like a parameter that would allow you to enter a width in the element properties window of the selected wall(s)?
we would like to have a generic wall (outline only) that the width can be changed per wall for layout purposes, then the walls will be selected & changed later to an actual wall with known materials.
I used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies View Relatedhow I keep the three risers shown in the image below, but extend the landings on the first and third run to avoid creating the angled corners. The angled corners show up when I manually edit the edges to bring the second run width down to match the first and third run width.
If I extend the landings, it tends to push one of the second run risers around the corner to the third run, and that screws up my design.
I quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedIn Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies View RelatedI did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies View Relatedhave trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View Related