In the file attached, there's a wall roof window joint showing the following problem: It seems like the window interferes with the joint, so that it isn't right, if the window is not situated higher than the roof slab. In the picture, the joint on the left side is correct, but the ones on the left are incorrect.
View 4 RepliesI keep getting a Revit warning 'Highlighted walls are attached to, but miss, the highlighted targets.' when I try and attach part of a long wall, spanning between gables, to the underside of roof eave. I must emphasise that this happens on a long wall where I have edited the profile to create three step levels each with a roof on them. Parts of this wall do attach to their respective length of roof but others don't. I wonder if this is something to do with the wall's height parameter, which is the same for the whole length of the wall but will have differing distances to the edited profile?
View 1 Replies View RelatedI know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies View RelatedI am drawing up my house in Revit to get use to the software. I created my house, and now my garage. I selected to create a roof by footprint but when I tried to join the roof to the adjacent wall, the overhang does not follow. I then selected the overhang to join to the adjacent wall but an error pops up: "Part of the roof to be joined misses the target face."
I attached a PDF of the roof.Also, you will notice a line that separates the two walls I joined together. I may separate them but how do I avoid this if I want to make one solid wall?
As for the wall selection, I have vinyl siding and would like to use properties that relate when selecting my exterior walls. I do not see anything regarding that besides wood siding. I thought that should be in my properties when I downloaded and purchased the software.
how to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
Exist a way to Attach the top of the wall in a element that is not a floor or roof. I have a wall under a stair and i want to make de top of the with a slope.
View 2 Replies View RelatedI am trying to get my drawings into revit but I am stuck on getting the basic form of the building in Revit.
Since I am using slanted walls I need to work with a Mass but I can't get the mass look like my idea. The picture I attached is a simple screen capture of Rhino with the outline of the building.
I have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies View RelatedIs there a way to get the default wall/roof/floor materials to appear transparent?
View 1 Replies View RelatedOur model uses several material types for insulation, mostly rigid variations at this point. The various materials are used in floor, wall and roof systems. Is there a way to create a single schedule that would list insulation quantities across all three system types?
View 2 Replies View RelatedWhat I am trying to do is to model a roof using Revit Lt so that the roof tiling and battens carry on over the gable wall. Is it possible to add a void profile to the roof slab in order to achieve this or do I need to model a small section of roof to just cover the wall portion?
View 3 Replies View RelatedI would like to know whether it is possible (and how) to trim a wall that was generated from mass face to a roof (also generated from face mass) or/and make a horizontal hole in it. The wall itself is not straight or curved, it shifts outwards from the building from base to top (still in an elevation it looks like rectangle).
View 2 Replies View RelatedCannot insert any window in this wall (its 140mm blockwork single skin trimmed to the roof above) and tried different window families. Yet I can cut an opening and also insert any door.
View 4 Replies View RelatedI can't put my nested window family in a curved wall. Where the problem could be situated? It has to be a normal straight window so I use my nested window families from other projects. I compared my NWF(nested window family) with the ones autodesk provides with revit but I don't find the difference. The NWF from autodesk work in a curved wall.
View 2 Replies View RelatedHow to add trim or diagonal sweeps to a curved wall. I have a circle top window in a curved wall and I need to add 1x4 trim around it.
View 1 Replies View RelatedI would like to cut a void into the wall of a host window family. When I place a void in the family, it does not cut thought the wall.
I tried making the void on a plane perpendicular and parallel to the wall plane. I dont know if this has anything to do with how voids work. But its not working. I also dont have an 'opening' element in the window family.
I'm working on a small project: a 2 story single house.
There are some curtain walls in the house. Also, a sliding glass door within the curtain wall. I want the same window schedule covers both the regular fixed windows and curtain walls.
Is it better to convert the curtain walls to regular windows? Or there are other better options?
Is it possible to use something like a parameter that would allow you to enter a width in the element properties window of the selected wall(s)?
we would like to have a generic wall (outline only) that the width can be changed per wall for layout purposes, then the walls will be selected & changed later to an actual wall with known materials.
I am working on my first real Revit project. i need to modify a windows family and in particular i want to change the axis of insertion of the window in the wall. I mean... my window should be placed on the outer edge of my wall. i try to unlock the dimensions that define its position and then i lock the dimension in the new position; the window seems to be ok but only in the RFA file. When i imported it in my project file, the windows moves in the wrong way in my real wall.
View 4 Replies View RelatedI am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedHow do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
How to place the “midpoint” of window on the midpoint of wall?
In the screenshot below, I wanted to place the window from its midpoint to the midpoint of the wall. How this can be performed on Revit?
creat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedI am using AutoCad Architecture 2011. In the Style Manager, I created a wall style using a 8"CMU unit plus a 2" insulation board. I have a gable roof slab that intersects with the wall. I want to trim the insulation board along the bottom of the roof slab, and show the CMU above the roof slab.
View 3 Replies View RelatedI know that Archtecture uses views differently than the other AutoCAD verticals, but I'd still like to find a solution to this. When I use the 3DCLIP command to create section views of models created in Architecture, the wall and roof objects do not clip correctly. The clipping planes do not create sections of those objects.
Is there a way to get the 3DCLIP command to actually intersect wall and roof objects?
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
In maya 2012 n 13...the end joint not matching to parent joint...
after creating leg joints are spine joints...we set the orientation of joints..but last joint wil put NONE in option box right....after applying this the end joint orientation still in world axis instead of parent joint..
is this bug are is there any other option(other then jointOrientaion in the joint attributes)..
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.