Revit :: Create Roof With Same Line On Top Roof Face And Vertical Side Face?
Nov 4, 2011creat roof with same line on top roof face & roof vertical side face?
View 2 Replies
ADVERTISEMENT
Revit :: Attach Vertical Face Between Two Parts Of Roof Shown
Dec 6, 2011What is the best way to attach a vertical face between the two parts of the roof shown in the attached picture (so that there is no hole in the roof).
View 3 Replies View RelatedRevit :: Set Roof Edge-Face Square To Slope
May 31, 2006I have a generic 5" thick rectangular concrete roof layout with a single directional slope of 1:3.
Is there a way to have the bottom and upper edge-faces be square (Two Cut - Square) to the slope and not vertical (Two Cut - Plumb) ?
No facia applied to this roofing system. Just plane jane.
Revit :: Error / Part Of Roof To Be Joined Misses Target Face
May 10, 2005Everytime I try to join a room I get this error "Part of the roof to be joined misses the target face"
View 5 Replies View RelatedRevit :: Trimming Wall To Roof / Making Horizontal Holes In Walls Created From Mass Face?
Dec 29, 2011I would like to know whether it is possible (and how) to trim a wall that was generated from mass face to a roof (also generated from face mass) or/and make a horizontal hole in it. The wall itself is not straight or curved, it shifts outwards from the building from base to top (still in an elevation it looks like rectangle).
View 2 Replies View RelatedRevit :: How To Create Roof On Left Hand Side Of Taller Area
Feb 5, 2014I attached a photo of the project i am working on. Im trying to figure out how to create the roof on the left hand side of the taller area. It should be a arched roof just like the others except it is also rounded.
View 3 Replies View RelatedAutoCad :: Conical Roof - Helical Radius Along Face Of Cone
Nov 11, 2011I have started a project and have a somewhat unusual condition. I have a structure with a Conical Roof. We are putting a parapet around this roof. With the parapet, we are also going to create 4 individual structures that direct water/rain flow to scuppers that will be fabricated into the parapet. Below is a sketch of our condition. How to get the shape of a line that follows the face of a cone. Obviously, this line is not projected to the center of the cone, so it is not just a straight line. I am imagining either a radial cut piece, or a complex/multiple radial cut piece. I don't really know how to put it into words exactly.... Take a look at the sketch.
Cone Info.jpg
Revit :: How To Have Single Slanted Roof Go Across Perimeter Of Home To Form A Roof
Dec 11, 2013I am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedRevit :: Get Roof Soffit To Have Same Rafter Cut As Roof?
Feb 11, 2014How do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View RelatedRevit :: To Create One Roof With 2 Different Slopes
Feb 20, 2012I have included a picture of the roof I am working on. As you can see I have 2 different roofs set up here, which doesnt look very good. I was wondering if there is a way to create one roof with 2 different slopes like I have here? I would like it to start out at a 3/12 slope for the first 4 feet and then switch to a 6/12 for the rest of the roof. I have not been able to figure out how to get this to work.
View 2 Replies View RelatedRevit :: Unable To Create Roof
Dec 6, 2012I had downloaded R.A 2012 last year and activated it. This past November, i had issues with my tower and reset it back to factory. Now I downloaded R.A 2013 first and now i can not download 2012 even when i go to "My Downloads" and try to reinstall it through Autodesk.
I have a project that requires 3 buildings and i am having a hard time making a roof for the second building. Some reason, I get "unable to create roof" when i get to the second building.
Revit :: How To Create Walkway For Sloping Roof
Aug 29, 2011I am new to Revit architecture and in the process of learning the software. How do I create a roof walkway for a sloping roof. these walkways are for people to be able to securely walk on the roof for maintainance of mechanical equipment fitted on the roof. Of the walkway will be along the gradient of the roof.
View 1 Replies View RelatedRevit :: 2012 Can't Create Shed Roof
Nov 23, 2011WHen I create a roof on level two of my project, I get only two choices of roof. When I go to roof edit, I get system family basic roof, and glazed panel. No other roof families to load.
I simply want to attach a shed roof to the upper part of wall (at level 2), and it only allows me to create a hip roof.I can't seem to modify it, other than to change roof slope. I've looked at a couple of videos, but the featuers in the videos don't seem to be there.
Note that the walls are sloping (in order to shed rain). I also cannot create a slope on the top edge of the wall in elevation view, but that's another story.How to I modify the hip roof to create a flat, if that's what I must do?
Revit :: Parapet Interior Wall Finish Above Roof Line
Aug 21, 2012I have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies View RelatedRevit :: How To Create Glass Roof Structure Over Staircase
Jul 22, 2013I am trying to create a glass roof structure over a staircase (see attached image - underground roof). I thought that I would do this by creating an in place mass, then adding either a roof or probably more likely a curtain wall system to the faces. However I am struggling to create the mass. I have made a wireframe of the roof (wireframe) using lines where the roof folds are, in autocad. I have then linked this in to Revit.
When I come to creating the Mass, I can only place lines using the "Pick line tool", which then only places lines on a specific reference plane (level 1,2 etc), so I only get a 2d footprint of the area I want to create this mass.
If I try to create a mass face using the 3d snapping tickbox, Revit fails to register that there are any lines for me to snap too. I have tried to "Tab", but this doesn't work either.
Revit :: Create Roof / Floor Using Work Plane?
Mar 28, 2013I need to create a sloped roof. I want to base this roof upon a beam system created using a sloped work plane rather than offset from a level. I now understand that (for some reason) Revit will not create floors or roofs using work planes, but only on levels, and I know that I can create a flat roof on a level and apply slope arrows and adjust the offset height, etc. etc. but that is very imprecise (lots of micro adjustments) and a lot of steps.
Isn't there any way to create a floor or roof using a work plane as the level?
The attached image shows a roof I created "by face" from a box mass element I set on the plane - unfortunately now I cannot edit the outline to get it to fint my non-rectangular roof.
AutoCAD Architecture :: What Is The Disadvantage To Convert Ia Roof To Roof Slab
May 15, 20131.How can I edit the roof in attached dwg to be like in attached jpg?
One option I think it would be to convert it to roof slab.
What is the disadvantage (if any) to convert ia roof to roof slab?
Can I create it in other way ?
2. In section 2, the first floor walls ends in 90 degrees angle at the roof. Can the walls be edited so that the joint line with the roof follow the roof slope?
Photoshop :: Editing Photo Face - Left Side Is Lighter Than Right Side?
Sep 2, 2012Im having a problem editing a photo 'face' one side 'left' side is lighter than the right side because of lighting. I was wondering If I could get both sides even prefably the lighter side like the normal side.
Is this possible? Because everytime I try edit the lighter side it still remains lighter.
Revit :: Can't Create Wall By Face
Mar 26, 2013I am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.
Revit :: How To Constrain Curved Ribs On A Curved Roof Line
Jan 26, 2014Having a time getting ribs to align 2m below top of ridge beam, and connect to curved wall below. I created one, then arrayed, but the radius changes at each 2.5 degree interval. I don't think I should have to calculate the % radius change to get the beams to do this. Some constraint button maybe?
Not sure if editing a wall profile is the best way to model this, but it's working.
AutoCad :: Create Text To Align With The Face Of Isometric Line?
Sep 23, 2011there a way to create text to align with the face of an isometric line?
View 9 Replies View RelatedRevit :: How To Join Two Roof
Aug 19, 2013I have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies View RelatedRevit :: How To Add Soffit To A Roof
Feb 10, 2012How do you add a soffit to a roof?
View 2 Replies View RelatedRevit :: Dormer In Existing Roof
Mar 25, 2013I have an existing roof with a new dormer.NEW dormer is created in a view with phase filter set to Show Existing+New Shouldn't the roof opening be shown as demo in the demo view??
When the opening is selected, the properties show the Phase Created=Existing and it is grayed out and not able to change to New Construction.
I'm using Revit Arch LT 2013. I do not need to know what Revit can and cannot do.
Revit :: Joining Walls To Roof
Apr 11, 2013I am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
Revit :: Creating A Shed Roof?
Nov 25, 2011I'm trying to create a simple shed roof attached to the sloping walls of a rectangular building. 4 walls, south wall 10' h, north wall 11" h, and the east/west walls joining them are therefore sloped.
I want to attach a simple shed roof to the top. Here's how I think I should do it:
1. create a new workplane aligned with the top of the walls.
2. switch to that workplane.
3. use "Roof" - Extrude" option to create the roof.
Assuming I'm correct in my steps above, I should be able to create the roof.
QUestion - How do I CREATE a new workplane where there is no object already to choose? Program won't let me create a workplane in workplane viewer by picking the tops of the four walls (in any of the tiled views). What am I missing?
Revit :: Curved Slope On A Roof
Jan 8, 2013I'm working on a blueprint and trying to get my roof to do something besides a straight slope, but it isn't going well. I need the roof to curve from the corners inward to the point, like the top of a Japanese pagoda.
View 1 Replies View RelatedRevit :: Edit A Roof Assembly
May 15, 2008I am trying to edit a roof assembly. My top layer is a roofing membrane. I give the roofing membrane a thickness and try to save and I get an error message saying that it needs to be 0" thickness. I set the thickness to 0" and I get an error message saying that it needs a thickness. How do I get pass this Catch 22?
View 5 Replies View RelatedRevit :: Can't Get Roof Of House To Join Together At All
Feb 12, 2014I have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 Replies View RelatedRevit :: Roof Pitch - How To Get 4/12 Or 5/12 And So On From Fractions
Oct 6, 2011Determine the roof pitch, then it has the typical triangle with 1/2 pitch and 1/4, 1/3, 1/6 and so on. I know rise over run like 5/12, but don't understand the fractions. How do I get 4/12 or 5/12 and so on from the fractions?
View 4 Replies View RelatedRevit :: Roof Visibility For Underlay
Jul 18, 2011I've attached a couple images of a visibility problem I'm having. The ROOF image shows the underlay view I'm using in the NO ROOF view in my revit project. I modeled all four of the dormer roofs the same, in place roof components, and they show up in the roof plan, but not when I use the roof plan as an underlay for my framing plan.
They don't show up when I toggle on the hidden elements tool either. I checked to make sure I didn't have coarse scale visibility turned off as well as if I had not visible in plan unchecked. These things seem fine, plus, as you can see, it shows up in it's own view. View range seems to be fine too. I can't figure out why these elements don't show up.