Revit :: Unable To Create Roof
Dec 6, 2012
I had downloaded R.A 2012 last year and activated it. This past November, i had issues with my tower and reset it back to factory. Now I downloaded R.A 2013 first and now i can not download 2012 even when i go to "My Downloads" and try to reinstall it through Autodesk.
I have a project that requires 3 buildings and i am having a hard time making a roof for the second building. Some reason, I get "unable to create roof" when i get to the second building.
View 1 Replies
ADVERTISEMENT
Nov 4, 2011
creat roof with same line on top roof face & roof vertical side face?
View 2 Replies
View Related
Feb 20, 2012
I have included a picture of the roof I am working on. As you can see I have 2 different roofs set up here, which doesnt look very good. I was wondering if there is a way to create one roof with 2 different slopes like I have here? I would like it to start out at a 3/12 slope for the first 4 feet and then switch to a 6/12 for the rest of the roof. I have not been able to figure out how to get this to work.
View 2 Replies
View Related
Aug 29, 2011
I am new to Revit architecture and in the process of learning the software. How do I create a roof walkway for a sloping roof. these walkways are for people to be able to securely walk on the roof for maintainance of mechanical equipment fitted on the roof. Of the walkway will be along the gradient of the roof.
View 1 Replies
View Related
Nov 23, 2011
WHen I create a roof on level two of my project, I get only two choices of roof. When I go to roof edit, I get system family basic roof, and glazed panel. No other roof families to load.
I simply want to attach a shed roof to the upper part of wall (at level 2), and it only allows me to create a hip roof.I can't seem to modify it, other than to change roof slope. I've looked at a couple of videos, but the featuers in the videos don't seem to be there.
Note that the walls are sloping (in order to shed rain). I also cannot create a slope on the top edge of the wall in elevation view, but that's another story.How to I modify the hip roof to create a flat, if that's what I must do?
View 2 Replies
View Related
Jul 22, 2013
I am trying to create a glass roof structure over a staircase (see attached image - underground roof). I thought that I would do this by creating an in place mass, then adding either a roof or probably more likely a curtain wall system to the faces. However I am struggling to create the mass. I have made a wireframe of the roof (wireframe) using lines where the roof folds are, in autocad. I have then linked this in to Revit.
When I come to creating the Mass, I can only place lines using the "Pick line tool", which then only places lines on a specific reference plane (level 1,2 etc), so I only get a 2d footprint of the area I want to create this mass.
If I try to create a mass face using the 3d snapping tickbox, Revit fails to register that there are any lines for me to snap too. I have tried to "Tab", but this doesn't work either.
View 9 Replies
View Related
Mar 28, 2013
I need to create a sloped roof. I want to base this roof upon a beam system created using a sloped work plane rather than offset from a level. I now understand that (for some reason) Revit will not create floors or roofs using work planes, but only on levels, and I know that I can create a flat roof on a level and apply slope arrows and adjust the offset height, etc. etc. but that is very imprecise (lots of micro adjustments) and a lot of steps.
Isn't there any way to create a floor or roof using a work plane as the level?
The attached image shows a roof I created "by face" from a box mass element I set on the plane - unfortunately now I cannot edit the outline to get it to fint my non-rectangular roof.
View 1 Replies
View Related
Feb 5, 2014
I attached a photo of the project i am working on. Im trying to figure out how to create the roof on the left hand side of the taller area. It should be a arched roof just like the others except it is also rounded.
View 3 Replies
View Related
Dec 11, 2013
I am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies
View Related
Feb 11, 2014
How do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies
View Related
Mar 24, 2013
I'm trying to create a new local file but the option is greyed out (not available). We're using Revit Server 2013 and we have one Central Server and two Accelerators in different locations. This issue is affecting only one of the two locations.
View 1 Replies
View Related
Jun 6, 2012
I need to resolve the corner condition where two boards intersect. I am not able to create a void in order to cut the corner for the geometry. I would like to shape more than one side of the board and make it rounded. How do I edit the different sides of the geometry?
See attachment for Revit model:
View 9 Replies
View Related
Jul 24, 2012
Having trouble creating arrays of ceiling light fixtures in Revit 2013? It gives me this error message;
'Can't place inserts outside of hosts. These elements won't be copied'
I've adjusted all manner of settings to make sure the copies don't fall outside the limits of the host ceiling but without success. It only occurs with linear arrays on ceilings not radial arrays for ceilings or linear or radial arrays for walls?
View 9 Replies
View Related
Aug 19, 2013
I have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies
View Related
Feb 10, 2012
How do you add a soffit to a roof?
View 2 Replies
View Related
Mar 25, 2013
I have an existing roof with a new dormer.NEW dormer is created in a view with phase filter set to Show Existing+New Shouldn't the roof opening be shown as demo in the demo view??
When the opening is selected, the properties show the Phase Created=Existing and it is grayed out and not able to change to New Construction.
I'm using Revit Arch LT 2013. I do not need to know what Revit can and cannot do.
View 8 Replies
View Related
Apr 11, 2013
I am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
View 2 Replies
View Related
Nov 25, 2011
I'm trying to create a simple shed roof attached to the sloping walls of a rectangular building. 4 walls, south wall 10' h, north wall 11" h, and the east/west walls joining them are therefore sloped.
I want to attach a simple shed roof to the top. Here's how I think I should do it:
1. create a new workplane aligned with the top of the walls.
2. switch to that workplane.
3. use "Roof" - Extrude" option to create the roof.
Assuming I'm correct in my steps above, I should be able to create the roof.
QUestion - How do I CREATE a new workplane where there is no object already to choose? Program won't let me create a workplane in workplane viewer by picking the tops of the four walls (in any of the tiled views). What am I missing?
View 8 Replies
View Related
Jan 8, 2013
I'm working on a blueprint and trying to get my roof to do something besides a straight slope, but it isn't going well. I need the roof to curve from the corners inward to the point, like the top of a Japanese pagoda.
View 1 Replies
View Related
May 15, 2008
I am trying to edit a roof assembly. My top layer is a roofing membrane. I give the roofing membrane a thickness and try to save and I get an error message saying that it needs to be 0" thickness. I set the thickness to 0" and I get an error message saying that it needs a thickness. How do I get pass this Catch 22?
View 5 Replies
View Related
Feb 12, 2014
I have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 Replies
View Related
Oct 6, 2011
Determine the roof pitch, then it has the typical triangle with 1/2 pitch and 1/4, 1/3, 1/6 and so on. I know rise over run like 5/12, but don't understand the fractions. How do I get 4/12 or 5/12 and so on from the fractions?
View 4 Replies
View Related
Jul 18, 2011
I've attached a couple images of a visibility problem I'm having. The ROOF image shows the underlay view I'm using in the NO ROOF view in my revit project. I modeled all four of the dormer roofs the same, in place roof components, and they show up in the roof plan, but not when I use the roof plan as an underlay for my framing plan.
They don't show up when I toggle on the hidden elements tool either. I checked to make sure I didn't have coarse scale visibility turned off as well as if I had not visible in plan unchecked. These things seem fine, plus, as you can see, it shows up in it's own view. View range seems to be fine too. I can't figure out why these elements don't show up.
View 4 Replies
View Related
Aug 22, 2013
I am trying to make a unique roof but I have had many failed attempts for hours now. Attached is a photo of the roof overhang I am trying to mimic and a crappy sketch showing the same thing. The roof has a normal gable on one end, but on the other. I need the over hand to go out three feet, then into a point at six feet at the same slope as the entire roof. NOT a hip roof which seems to be the only they I can make it. I even tried making a separate roof piece and it still didnt work.
View 1 Replies
View Related
Nov 9, 2012
how i would go about inserting rooflights in this curved roof.
View 7 Replies
View Related
Sep 1, 2011
I am attempting to add fascia to a curved roof. The fascia is built as a wall type. The fascia follows the radius of the curved roof in plan view, but not in elevation view. How to get the fascia to follow the roof curve in elevation view?
View 1 Replies
View Related
Mar 27, 2012
I am stuck on how to put a gable end on a pitched roof.
View 1 Replies
View Related
May 26, 2013
I am trying to make my roof by footprint but everytime I try the footprint won't show up. Are there specific steps to connect the two? I am working off directions for Revit 2011 but with 2013 its not working the same.
View 1 Replies
View Related
Mar 7, 2012
I created a volumetric mass and then i tried to put a roof on a upper surface curvilinear very complex, it got error on application roof and i'm not able to resolve
View 4 Replies
View Related
Jan 13, 2013
how do I post revit files and jpgs?why won't the roof install with the overhang? I set it to 12", click on the walls and no matter what I try, I get a general message that I can not produce roof. When I click on lines, I get a roof without an overhang.How do you fill in the gable ends?
View 2 Replies
View Related
Mar 20, 2012
I used the roof by footprint tool. I was constructing a flat roof structure. I clicked the walls to construct the roof. All the pink lines were joined but when i clicked on the green tick to complete the roof it came up with an error saying the lines were too short. the roof had an overhang set of 300mm.
View 1 Replies
View Related
