I have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 RepliesI have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies View RelatedI am drawing up my house in Revit to get use to the software. I created my house, and now my garage. I selected to create a roof by footprint but when I tried to join the roof to the adjacent wall, the overhang does not follow. I then selected the overhang to join to the adjacent wall but an error pops up: "Part of the roof to be joined misses the target face."
I attached a PDF of the roof.Also, you will notice a line that separates the two walls I joined together. I may separate them but how do I avoid this if I want to make one solid wall?
As for the wall selection, I have vinyl siding and would like to use properties that relate when selecting my exterior walls. I do not see anything regarding that besides wood siding. I thought that should be in my properties when I downloaded and purchased the software.
Followed all the steps found online, but when I select "Join Roof", the cursor will not select any of the edge lines (tried on multiple roofs). Software Error? Revit 2014 Architecture.
View 1 Replies View RelatedI recall the "Paint" program you could make a Circle, and drag the circle till you had a tin can or a barrel.How do we do that in <paint.NET>?
View 5 Replies View RelatedI am drawing a house with a hip roof. The roof has a overhang with fascia and soffit. What is the best way to construct the components of the roof system. Should the hip roof and the soffit with fascia to be one system or two separate systems?
View 3 Replies View RelatedI am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedHow do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View Relatedcreat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedWhere do you start at when you are creating the electrical plans for a house?
View 6 Replies View Relatedi want to create a basic house template. how do i do this so it will keep all walls i create and all familys i load. i have made a template before but when i open a project using this template none of the walls , floor, of families are present.
View 2 Replies View RelatedHow do you add a soffit to a roof?
View 2 Replies View RelatedI have an existing roof with a new dormer.NEW dormer is created in a view with phase filter set to Show Existing+New Shouldn't the roof opening be shown as demo in the demo view??
When the opening is selected, the properties show the Phase Created=Existing and it is grayed out and not able to change to New Construction.
I'm using Revit Arch LT 2013. I do not need to know what Revit can and cannot do.
I am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
I have included a picture of the roof I am working on. As you can see I have 2 different roofs set up here, which doesnt look very good. I was wondering if there is a way to create one roof with 2 different slopes like I have here? I would like it to start out at a 3/12 slope for the first 4 feet and then switch to a 6/12 for the rest of the roof. I have not been able to figure out how to get this to work.
View 2 Replies View RelatedI'm trying to create a simple shed roof attached to the sloping walls of a rectangular building. 4 walls, south wall 10' h, north wall 11" h, and the east/west walls joining them are therefore sloped.
I want to attach a simple shed roof to the top. Here's how I think I should do it:
1. create a new workplane aligned with the top of the walls.
2. switch to that workplane.
3. use "Roof" - Extrude" option to create the roof.
Assuming I'm correct in my steps above, I should be able to create the roof.
QUestion - How do I CREATE a new workplane where there is no object already to choose? Program won't let me create a workplane in workplane viewer by picking the tops of the four walls (in any of the tiled views). What am I missing?
I'm working on a blueprint and trying to get my roof to do something besides a straight slope, but it isn't going well. I need the roof to curve from the corners inward to the point, like the top of a Japanese pagoda.
View 1 Replies View RelatedI am trying to edit a roof assembly. My top layer is a roofing membrane. I give the roofing membrane a thickness and try to save and I get an error message saying that it needs to be 0" thickness. I set the thickness to 0" and I get an error message saying that it needs a thickness. How do I get pass this Catch 22?
View 5 Replies View RelatedDetermine the roof pitch, then it has the typical triangle with 1/2 pitch and 1/4, 1/3, 1/6 and so on. I know rise over run like 5/12, but don't understand the fractions. How do I get 4/12 or 5/12 and so on from the fractions?
View 4 Replies View RelatedI've attached a couple images of a visibility problem I'm having. The ROOF image shows the underlay view I'm using in the NO ROOF view in my revit project. I modeled all four of the dormer roofs the same, in place roof components, and they show up in the roof plan, but not when I use the roof plan as an underlay for my framing plan.
They don't show up when I toggle on the hidden elements tool either. I checked to make sure I didn't have coarse scale visibility turned off as well as if I had not visible in plan unchecked. These things seem fine, plus, as you can see, it shows up in it's own view. View range seems to be fine too. I can't figure out why these elements don't show up.
I had downloaded R.A 2012 last year and activated it. This past November, i had issues with my tower and reset it back to factory. Now I downloaded R.A 2013 first and now i can not download 2012 even when i go to "My Downloads" and try to reinstall it through Autodesk.
I have a project that requires 3 buildings and i am having a hard time making a roof for the second building. Some reason, I get "unable to create roof" when i get to the second building.
I am trying to make a unique roof but I have had many failed attempts for hours now. Attached is a photo of the roof overhang I am trying to mimic and a crappy sketch showing the same thing. The roof has a normal gable on one end, but on the other. I need the over hand to go out three feet, then into a point at six feet at the same slope as the entire roof. NOT a hip roof which seems to be the only they I can make it. I even tried making a separate roof piece and it still didnt work.
View 1 Replies View Relatedhow i would go about inserting rooflights in this curved roof.
View 7 Replies View RelatedI am attempting to add fascia to a curved roof. The fascia is built as a wall type. The fascia follows the radius of the curved roof in plan view, but not in elevation view. How to get the fascia to follow the roof curve in elevation view?
View 1 Replies View RelatedI am stuck on how to put a gable end on a pitched roof.
View 1 Replies View RelatedI am trying to make my roof by footprint but everytime I try the footprint won't show up. Are there specific steps to connect the two? I am working off directions for Revit 2011 but with 2013 its not working the same.
View 1 Replies View RelatedI created a volumetric mass and then i tried to put a roof on a upper surface curvilinear very complex, it got error on application roof and i'm not able to resolve
View 4 Replies View Relatedhow do I post revit files and jpgs?why won't the roof install with the overhang? I set it to 12", click on the walls and no matter what I try, I get a general message that I can not produce roof. When I click on lines, I get a roof without an overhang.How do you fill in the gable ends?
View 2 Replies View RelatedI used the roof by footprint tool. I was constructing a flat roof structure. I clicked the walls to construct the roof. All the pink lines were joined but when i clicked on the green tick to complete the roof it came up with an error saying the lines were too short. the roof had an overhang set of 300mm.
View 1 Replies View RelatedWhen working with mullions, there is a "Toggle mullion join" at the end of each mullion and you have to pick each one individually to toggle. Is there any way to pick a group of mullions and have them all toggle at once?
View 2 Replies View RelatedI have 2 corners between 3 walls, one of which is of an odd construction. I want the outer layers of the two side walls to meet as they do when trimmed to each other but this creates a bit of angled wall inside the room on the upper left. I want that corner to look like the left and top walls are trimmed. The two corners are too far apart for wall join to clean the whole intersection and I can't really move any of these walls.
Here's a video of trimming the walls.
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013