AutoCAD Civil 3D :: 2012 Retaining Wall Assembly And Wall Height?
Jul 23, 2012
I am using the RetainWallVertical subassembly with a created gutter subassembly attached to the wall and a DaylightGeneral subassembly attached to the gutter assembly. My cut slope parameter is set to hold at 1.5:1. I would like to use a target (feature line or alignment) to daylight to and have the wall height adjust accordingly. Problem, I am not able to use a target other than a surface for daylighting. I can use my existing ground surface, which I am daylighting too, but I can't adjust the target point.
View 2 Replies
ADVERTISEMENT
May 27, 2009
MSE Retaining Wall subassembly? or any type of retaining wall subassembly that does NOT have a footing or where I can find one?
View 4 Replies
View Related
Sep 8, 2012
I have a platform at level 13.275m and nearby there is a retaining wall at aprox. level 4.0m.
For the wall i've made a surface using feature lines from EG till level 15.0m and then pasted into the EG surface to create the 'barrier' for the slope. But when i do the grading with the fill slope projection to surface, when it reaches the retaining wall section, the contour lines go crazy and if i do a quick profile, the fill slope line (obvious) is iregular, rather than a straight down line (2:1) going from level 13.275m till it hits the EG.
I've attached a picture to show the problem better.
View 9 Replies
View Related
Apr 16, 2013
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
View 3 Replies
View Related
Apr 11, 2012
I have a feature line as the top of a wall and want to grade up away from it to marry to existing ground.
View 1 Replies
View Related
May 3, 2012
I am in Civil3D 2012, and am trying to render a retaining wall we doing. I set up a corridor, surface, and profile, and have it working with plans and such, but when I try my hand at rendering it looks rather odd. The surface is fine, and I can choose materials on the vertical wall subassembly, but It just shows a paper thin object ever 25' and a large surface on top. Does the top of the wall need a feature line as well.
View 1 Replies
View Related
Jun 12, 2009
Linetype code that represents blocks in a retaining wall, lets say for instance Keystone type blocks?
View 1 Replies
View Related
Mar 24, 2013
I created a wall via RECTANGLE/PRESSPULL to a desired height. But I need to be able to increase the height of one corner of the wall. Not quite sure how to do this.
On the attached picture, corner A needs to remain where it is, while corner B needs to be 3' higher.
View 4 Replies
View Related
Sep 13, 2013
i need a lisp that construct line between two lines of wall by selection called (Wall Centerline)
i attach example of what i want assuming that i will often isolate wall layer in the project to facilitate the task.
View 3 Replies
View Related
Jun 3, 2013
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies
View Related
Dec 7, 2011
I'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
View 1 Replies
View Related
Jun 12, 2012
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies
View Related
Apr 14, 2011
I can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
View 1 Replies
View Related
Apr 12, 2012
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies
View Related
Jul 25, 2013
I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
View 9 Replies
View Related
Dec 4, 2012
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies
View Related
Nov 27, 2011
Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
View 1 Replies
View Related
Oct 31, 2013
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
View 1 Replies
View Related
Jul 29, 2011
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies
View Related
Apr 1, 2011
How do I set a Window Assembly to be flush to the outside of a Wall? I'm expecting an embarrassingly simple answer, but I really cannot figure this. the infills and the mullions move out 7-1/16", but the two frame elements just will not be moved.
View 1 Replies
View Related
May 1, 2013
We just upgraded from ACA 2011 to ACA2012 and we are getting some wall cleanup issues with foundations. some walls, the footings show while adjacent wall (same style) footing disappears.
also, when i copy a wall where the footing is missing, the new copied wall shows the footing. when i move a wall without a footing, the footing shows up.
View 1 Replies
View Related
Apr 7, 2013
“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
View 3 Replies
View Related
Jan 28, 2013
I am doing casting model in the inventor. i need to check the modelling wall thickness.
I tried in section analysis & drafting method but i am not satisfy on that.
View 1 Replies
View Related
Jan 17, 2013
I am trying to change the wall assembly of my foundations (getting rid of a layer of EIFS) and it won't let me delete the layer or change the width (although I can change it into an airbarier). Is there any way to control what parts of the wall are locked in the "edit assembly" window?
I am very new to Revit and am using a student version, I'm nt sure if that changes things.
View 2 Replies
View Related
May 23, 2007
I can tag walls by entering the wall type in the 'type mark' box in the assembly's properties, but is there a way of listing out the material of each type of wall that has been used in the project. e.g:
Wall Type P1
16mm Gypsum Board
92mm Steel Stud
16mm Gypsum Board
View 2 Replies
View Related
Nov 1, 2013
Im working on creating all of our common AutoCAD annotation symbols in revit.
For section details we use a wall asembly tag that wraps the thickness of the wall, and its set up so we pull the arrows to match the width of the assembly. (see attatchment)
Im struggling to find a way to make this work in Revit as well, either by automatically adjusting to the width of the assembly we are tagging, or even by just pulling the arrows like we did in autocad.
View 1 Replies
View Related
Sep 11, 2013
I want to export from Revit 2013 to AutoCAD so that each component of a wall assembly exports to a separate AutoCAD layer. For example on a simple stud wall with drywall on both sides I would like the interior lines on different layers than the lines for the outside faces. Is this possible?
View 2 Replies
View Related
Jun 23, 2012
This is the first time I experience a major problem with Revit 2012. I created a duplicate of an 8" concrete masonry wall for my student project. Then I selected the Edit option in the Structure to change the rendered material to concrete masonry. Suddenly the program freezes and crashes. A window pops up stating that Windows has detected a problem with Revit and must shut the program down. I've everything since my last save. As of now, I recreated a duplicate of the masonry wall I need and started drawing some of the walls for my project but I'm afraid to experiment with other materials. Background Information about my computer: I downloadeda free version of Revit 2012 student software to practice at home. I have Windows 7 64-bit, 6GB of Ram and Intel (R) Core i7 2.20GHz...(I checked all the software requirements before downloading the correct version of Revit 2012)
Do I have to uninstall the program and reinstall it again? Would the problem go away?
View 1 Replies
View Related
Apr 17, 2013
The 2013 .NET API exposes just 10 of the 22 PartDataFields for Pipe objects. WTh (Wall thickness) is not one of them so I'm attempting to get it via Late Binding. This lisp code works, where (vl-sel) is just a helper function to select an object and convert it to a vla-object:
(setq pdr (vlax-get (vl-sel) 'partdatarecord))(setq itm (vlax-invoke pdr 'find "WTh"))
to get the PartDataField. However, putting this into my C# code, it fails on the Find portion with an exception
//ps is a valid PartSize objectPartDataRecord pdr = ps.SizeDataRecord;PartDataField diafld = pdr.GetDataFieldBy(PartContextType.PipeInnerDiameter);object[] args = new object[1];
object acadobj = ps.AcadObject;
object pdrobj = acadobj.GetType().InvokeMember("PartDataRecord", System.Reflection.BindingFlags.GetProperty, null, acadobj, null);
args[0] = "WTh";
[code]....
View 3 Replies
View Related
Jun 3, 2012
I don't know how to create the secondary containment wall by civil3d.it's the same as creating the retainment wall assembly ?
View 2 Replies
View Related
Apr 12, 2013
I am experiencing a problem in 2013. In part builder, I am trying to add wall thicknesses to the simple cylinder. I was able to add options for inside diameter and set floor thickness to a list and add options for that, but when I try to set wall thickness to list instead of constant, I get an error in the value menu.
Everything disappears and in red at the bottom, I get a message about an error in calculations. I even tried temporarily deleting the With from any calculations, but I still got the error. I have had no problems doing this in 2011 or 2009.
View 2 Replies
View Related
