i need a lisp that construct line between two lines of wall by selection called (Wall Centerline)
i attach example of what i want assuming that i will often isolate wall layer in the project to facilitate the task.
Using Lisp or VLisp, how can I find the Start & End Point of an AEC_WALL ent. ?
View 5 Replies View RelatedLinetype code that represents blocks in a retaining wall, lets say for instance Keystone type blocks?
View 1 Replies View RelatedLisp to draw a line along the length of a 3d solid? I have some UB (I sections) columns and beams modeled and would like to select all solids and for it draw a centerline end to end
View 7 Replies View RelatedWhat is the easiest way to dimension to the centerline of a wall? I need to land a dimension tick where there is no line.
View 2 Replies View RelatedI have double line pipe drawings but i have to change distances between of this lines in entire drawing and i was thinking that maybe there is a lisp code which can create new double line according to my specify dimensions ...
example :
Distance between lines : 100 mm
------------------------
------------------------
here is what i want to do :
1. select double line
2. specify new distance ( for example 200 mm)
3. lisp will create center line middle of the selected lines ( maybe it can ask me that this center line will be permanently or not )
4. lisp will create new double line from this centerline according to my specific distance
5. new double line layers will be the same with selected old double line
and this lisp has to work for double arc or quarter circles too.
I'm drawing individual guest rooms for a hotel that I would like to xref into the main floor plans. The walls between the rooms are 8" wide. I would like to only show half the width of those walls (4") so when xrefed againt another guest room in the main floor plan, the total width would be 8". But I would like for the one side of the 4" wall to appear as a centerline on the individual plans, but at the same time, be able to shut the centerlines off on the main floor plans. I'm new to ACA 2012 and perhaps I'm going about this in the wrong way.........?????
View 8 Replies View RelatedI need lisp that do a line between 4 lines.
View 7 Replies View RelatedI want to construct lines between every two line ending point by multi selectio window instead of drawing it manually between lines ending point ?
View 3 Replies View Relatedwhy do not draw the line between ptm1 and pt3?
(defun c:PUNTOM (/ pt1 pt2 pt3) (setq pt1 (getpoint "
Initial point : ")) (setq pt2 (getpoint "
Final point : ")) (setq pt3 (getpoint "
Offset : "))(setq ptm1 (mid (pt1 pt2))) (command "_line" pt1 pt2 "")(command "_line" ptm1 pt3) (princ));;;;;;;(defun mid (p1 p2) (list (/ (+ (car p1) (car p2)) 2.0) (/ (+ (cadr p1) (cadr p2)) 2.0) ));;;;;;;;
have had the good fortune to have recieved a Christmas present (o.k. to myself) a new Dell 30" monitor with 2560 x 1600 resolution.
The only thing I am finding troublesome as you might be able to see by the attached screen shot, is that now my autocad menus are, as expected at the top of the screen. This new size of monitor brings with it the problem that you now have to travel your mouse a great distance to reach the menu bar items.
I need one lisp to get invert levels, I am having Invert levels and cordinates of two points of an arc how can I find invert level of a point middle of tht arc?
View 9 Replies View Relatedhow to make a toolbar button so that when i click it and select a few single text, it will automatically change the text base point to be at "MIDDLE CENTER"....
At the moment, i use to create a button with macro of " ^C^C_text;j;mc "....But the problem is whenever i use this button, i still need to type "MC" at the command prompt.. How to make it so that after i click the button, all i need to to is just select the text..
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI am using the RetainWallVertical subassembly with a created gutter subassembly attached to the wall and a DaylightGeneral subassembly attached to the gutter assembly. My cut slope parameter is set to hold at 1.5:1. I would like to use a target (feature line or alignment) to daylight to and have the wall height adjust accordingly. Problem, I am not able to use a target other than a surface for daylighting. I can use my existing ground surface, which I am daylighting too, but I can't adjust the target point.
View 2 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
Is there a lisp that will allow me to do a continuous dimension, but will alternate the dimension position from low, high, low and high? If there is no lisp already created, how to create one?
See Continuous dimension attachment for example.
I work at a glass and glazing company and this is how we dimension mullion width and DLO. See typical window dimensioning attachment for window elevation with dimensions.
I have a list ("temp.dwg" "temp2.dwg") and would like to add the string "insert text here" into each item in the list resulting in ("insert text heretemp.dwg" "insert textheretemp2.dwg"). how would i go about doing that using LISP?
View 2 Replies View RelatedIs there a way to programatically set a visual style before a drawing actually opens?
We have some huge models and people seem to forget to change their visual styles back to 2D wireframe before saving and exiting drawings. Some models will crash on some workstations when trying to open in a rendered mode.
I found a lisp with a function that looked to set viewport visual styles. But it does not seem to be supported anymore. --> (vla-put-VisualStyle vport 1)
I'm trying to write a lisp routine that, when I invoke the mleader command, osmode is set to "nearest" & orthomode is set off. I then would like the original settings to be returned.
attached is what I have written so far:-
Lisp that switches back on Selection Preview i.e. thickens and highlights lines when you hover over them?I don't know why, but they are always unticking the boxes.
View 4 Replies View Related