Revit :: Roof By Extrusion - Trim Section Outlined In Red
Nov 27, 2011I need to trim the section outlined in red, how do I go about doing that?
View 1 Replies
ADVERTISEMENT
Revit :: Edit Curved Roof By Extrusion?
Oct 31, 2012I have created a curved roof by extrusion but im looking to trim it as per the outline of the floorplan.
View 4 Replies View RelatedRevit :: Roof To Wall Section Cleanup
Aug 22, 2012I know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies View RelatedRevit :: Model Small Section Of Roof To Just Cover Wall Portion?
Jan 20, 2014What I am trying to do is to model a roof using Revit Lt so that the roof tiling and battens carry on over the gable wall. Is it possible to add a void profile to the roof slab in order to achieve this or do I need to model a small section of roof to just cover the wall portion?
View 3 Replies View RelatedRevit :: How To Have Single Slanted Roof Go Across Perimeter Of Home To Form A Roof
Dec 11, 2013I am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View RelatedAutoCad 3D :: Extend / Trim 3D Solid Roof Planes
Oct 8, 2012I am trying to use AutoCAD 2013 to create a complicated roof. What is the best way to extend 3D solid roof planes and to trim 3d Solid roof planes that intersect each other? I have tried slicing and can't quite get the hang of it!
View 9 Replies View RelatedRevit :: Get Roof Soffit To Have Same Rafter Cut As Roof?
Feb 11, 2014How do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View RelatedRevit :: Create Roof With Same Line On Top Roof Face And Vertical Side Face?
Nov 4, 2011creat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedAutoCAD Inventor :: How To Trim Away The Section
Apr 13, 2012how do i trim away the section on RevolutionSrf1 underneath features RevolutionSrf2 and LoftSrf1 ?
Inventor 2012
Revit :: Create Simple 8x2 Extrusion
Jun 25, 2012I'm trying to create a simple 8x2 extrusion that will represent an aluminum band on a building elevation. The length varies by instance but needs to be reportable in a schedule (preferably using the "Length" shared parameter name.
I've never used reporting parameters before but have made an attempt at it in the attached file. The parameter of Length displays the stretched length in the properties box but won't appear in a schedule. The Instance Length parameter will appear in a schedule but doesn't always show the correct value.
I'll note that this family was adapted from one already created by someone else and the Length label cannot be deleted. It's as if the file was at one time a template. However, I've tried it from scratch, too and can't get it to work, sometimes not even being able to get the family to allow stretching the length.
Revit :: Extrusion From Polylines Of Imported DXF Or DWG Models
Sep 1, 2013Why can't Revit make extrusion from polylines of imported DXF or DWG models? Revit 2013 update 3.
View 5 Replies View RelatedRevit :: Family Category To Create Extrusion
Jul 25, 2013Is there a Family Category that allows me to create an Extrusion that will then work with the “Attach Top/Base” tool?
For example, instead of using a structural column, I would instead like to use a Model In-Place Extrusion, then be able to attach these columns to my roof.
I’m noticing you don’t get the option to “Attach Top/Base” when you use a Model In-Place Extrusion.
Revit :: Reasons For Void Not Cutting Extrusion?
May 29, 2012What would be possible reason for a void not having any effect on cutting an object? I created a parametric void.Then I created an object.No change to the object. If I create an object then a void, it seems to work.
View 1 Replies View RelatedRevit :: How To Join Two Roof
Aug 19, 2013I have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies View RelatedRevit :: How To Add Soffit To A Roof
Feb 10, 2012How do you add a soffit to a roof?
View 2 Replies View RelatedRevit :: Rotated Solid Not Cut By Arrayed Extrusion Void
Nov 27, 2013I have created a simple pipe fitting family, a soil vent pipe terminal infact, but I cannot get the solid body created from a rotated profile to be cut by an arrayed extrusion void. I keep getting the error message, 'Can't keep the elements joined'!
View 2 Replies View RelatedRevit :: How To Create Circular Desk Without Void Extrusion
Jun 30, 2012I created a reception desk in Revit 2013 using solid extrusions and void extrusions and it looks really good. The problem is I need to recreate this thing using some other method since I cannot place door and drawer faces on a plane that technically, geometrically does not exist, ie the area a receptionist would sit. The rendering of my extruded desk is attached.
View 8 Replies View RelatedRevit :: Dormer In Existing Roof
Mar 25, 2013I have an existing roof with a new dormer.NEW dormer is created in a view with phase filter set to Show Existing+New Shouldn't the roof opening be shown as demo in the demo view??
When the opening is selected, the properties show the Phase Created=Existing and it is grayed out and not able to change to New Construction.
I'm using Revit Arch LT 2013. I do not need to know what Revit can and cannot do.
Revit :: Joining Walls To Roof
Apr 11, 2013I am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
Revit :: To Create One Roof With 2 Different Slopes
Feb 20, 2012I have included a picture of the roof I am working on. As you can see I have 2 different roofs set up here, which doesnt look very good. I was wondering if there is a way to create one roof with 2 different slopes like I have here? I would like it to start out at a 3/12 slope for the first 4 feet and then switch to a 6/12 for the rest of the roof. I have not been able to figure out how to get this to work.
View 2 Replies View RelatedRevit :: Creating A Shed Roof?
Nov 25, 2011I'm trying to create a simple shed roof attached to the sloping walls of a rectangular building. 4 walls, south wall 10' h, north wall 11" h, and the east/west walls joining them are therefore sloped.
I want to attach a simple shed roof to the top. Here's how I think I should do it:
1. create a new workplane aligned with the top of the walls.
2. switch to that workplane.
3. use "Roof" - Extrude" option to create the roof.
Assuming I'm correct in my steps above, I should be able to create the roof.
QUestion - How do I CREATE a new workplane where there is no object already to choose? Program won't let me create a workplane in workplane viewer by picking the tops of the four walls (in any of the tiled views). What am I missing?
Revit :: Curved Slope On A Roof
Jan 8, 2013I'm working on a blueprint and trying to get my roof to do something besides a straight slope, but it isn't going well. I need the roof to curve from the corners inward to the point, like the top of a Japanese pagoda.
View 1 Replies View RelatedRevit :: Edit A Roof Assembly
May 15, 2008I am trying to edit a roof assembly. My top layer is a roofing membrane. I give the roofing membrane a thickness and try to save and I get an error message saying that it needs to be 0" thickness. I set the thickness to 0" and I get an error message saying that it needs a thickness. How do I get pass this Catch 22?
View 5 Replies View RelatedRevit :: Can't Get Roof Of House To Join Together At All
Feb 12, 2014I have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 Replies View RelatedRevit :: Roof Pitch - How To Get 4/12 Or 5/12 And So On From Fractions
Oct 6, 2011Determine the roof pitch, then it has the typical triangle with 1/2 pitch and 1/4, 1/3, 1/6 and so on. I know rise over run like 5/12, but don't understand the fractions. How do I get 4/12 or 5/12 and so on from the fractions?
View 4 Replies View RelatedRevit :: Roof Visibility For Underlay
Jul 18, 2011I've attached a couple images of a visibility problem I'm having. The ROOF image shows the underlay view I'm using in the NO ROOF view in my revit project. I modeled all four of the dormer roofs the same, in place roof components, and they show up in the roof plan, but not when I use the roof plan as an underlay for my framing plan.
They don't show up when I toggle on the hidden elements tool either. I checked to make sure I didn't have coarse scale visibility turned off as well as if I had not visible in plan unchecked. These things seem fine, plus, as you can see, it shows up in it's own view. View range seems to be fine too. I can't figure out why these elements don't show up.
Revit :: Unable To Create Roof
Dec 6, 2012I had downloaded R.A 2012 last year and activated it. This past November, i had issues with my tower and reset it back to factory. Now I downloaded R.A 2013 first and now i can not download 2012 even when i go to "My Downloads" and try to reinstall it through Autodesk.
I have a project that requires 3 buildings and i am having a hard time making a roof for the second building. Some reason, I get "unable to create roof" when i get to the second building.
Revit :: Unique Roof Slope
Aug 22, 2013I am trying to make a unique roof but I have had many failed attempts for hours now. Attached is a photo of the roof overhang I am trying to mimic and a crappy sketch showing the same thing. The roof has a normal gable on one end, but on the other. I need the over hand to go out three feet, then into a point at six feet at the same slope as the entire roof. NOT a hip roof which seems to be the only they I can make it. I even tried making a separate roof piece and it still didnt work.
View 1 Replies View RelatedRevit :: Rooflights In A Curved Roof
Nov 9, 2012how i would go about inserting rooflights in this curved roof.
View 7 Replies View RelatedRevit :: How To Add Fascia To Curved Roof
Sep 1, 2011I am attempting to add fascia to a curved roof. The fascia is built as a wall type. The fascia follows the radius of the curved roof in plan view, but not in elevation view. How to get the fascia to follow the roof curve in elevation view?
View 1 Replies View RelatedRevit :: How To Make Gable End On Roof
Mar 27, 2012I am stuck on how to put a gable end on a pitched roof.
View 1 Replies View Related