AutoCAD Civil 3D :: 2012 - Error Message When Trying To Add A Line To A Surface

Jun 19, 2012

Just trying to clean up a surface.  I can swap edges fine.  This project was a 2009 project. 

View 1 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Error Adding Breakline Message When Editing Surface With Feature Lines

Jul 11, 2012

I am working on a 6 mile highway project whose surface file is 85MB big. So, I created a Data Shortcut of this surface and used this for creating profiles. However, at some locations the corridors go below the surface(as per their original profile) which was not intended. So, I need to restrict the surface to follow the corridors but not go beyond it.

I have created feature lines from corridors and tried to add them as breaklines to the surface. But " error adding breakline" error pops up. 

Is it because I am trying to add the breaklines to the mirror surface which I created from Data Shortcut ??

Will it be useful if I copy feature lines to original surface file and add these feature lines as breaklines in that file??

Windows 7 x 64
Nvidia Quadro 2000
24 GB Ram
i7 960 @ 3.20 GHz
Civil 3D 2012

View 2 Replies View Related

AutoCAD Civil 3D :: Error Message - Undefined Group Code 10 For Object On Line 2106

Aug 21, 2012

Undefined group code 10 for object on line 2106.

Invalid or incomplete DXF input -- drawing discarded.

I created stream profiles in RASPLOT using its DXF Editor but when I try to open up the DXFs in AutoCAD I get the above error.

View 3 Replies View Related

AutoCAD LT :: 2012 - Fatal Error Message At Program Start?

Oct 15, 2011

I am running acad lt 2012 on windows 7- at acad startup I am receiving a fatal error message

"unhandled access violation reading 0x008 exception at 4135104h"

Windows updates are all current.

View 1 Replies View Related

AutoCAD Architecture :: Desktop 2012 Section Error Message?

Apr 26, 2013

When trying to cut a section in ADT 2012 I get the following message:

Command: _AecVerticalSection

Command not allowed because drawing contains objects from a newer version of this application.

How can i get ADT 2012 to cut the section i need?

View 2 Replies View Related

AutoCAD LT :: Fatal Error Message When Saving Drawing In 2012?

Apr 15, 2013

We have AutoCad LT 2012 version. We encounter fatal error when we save the drawing. we cannot finish our job because everytime we save our work it will show a messsage FATAL ERROR.

View 5 Replies View Related

AutoCAD Architecture :: 2012 Crash With Empty Error Message On Exit?

Jun 27, 2012

When a user closes ACA 2012 (sp2)he gets an empty crash message.

We are running win7 64bit.

View 2 Replies View Related

AutoCAD Inventor :: Error Message File Needs To Update When Opening 2012

Oct 20, 2011

OK then update. I select never show this message agian ever (my favorite ) - but guess what a it pops back up. Nothing is wrong with the assembly

View 1 Replies View Related

AutoCAD Civil 3D :: Remove Feature Line Used As Break Line When Creating Surface

Dec 11, 2012

I needed to remove a feature line that I used as a break line when creating a surface.   When I removed the feature line from the definition of the surface, the grading did not change.  It appears the points created by the feature line remain which is why grading didn't change.  The only work around was to delete these points. 

I noticed the same thing happens when I removed the surface boundary and inserted a new boundary.  why these points remain and how to remove when I delete boundary and feature line from surface?

View 9 Replies View Related

AutoCAD Civil 3D :: 2012 -> 2014 Change Is Surface Display?

Jan 2, 2014

heres the problem we had created a slope style in 2012 15% - 25% and 25% - 100%. done this many times with no problems. so we upgrade and open the file in 2014 now there is a large white area that c3d is filling in.

Win 7 pro 12gb
NVIDIA Quadro 2000
LDD 2009
IDS 2014

View 3 Replies View Related

AutoCAD Civil 3D :: Data Shortcut Surface From 2013 Into 2012?

Aug 29, 2012

Is it possible to data shortcut a surface from c3d2013 into c3d2012?

I tryed it and it says that the surface is in the drawing but its not showing up.

I've tried changing the style and the layer but nothing works.

View 1 Replies View Related

AutoCAD Civil 3D :: Error Message - Prevents Saving

Sep 20, 2010

The message reads "One or more objects in this drawing cannot be saved to the specified format. The operation was not completed and no file was created." I am using AutoCad Civil 3D 2011.

View 3 Replies View Related

AutoCAD Civil 3D :: Error Message-Out Of System Memory

Dec 1, 2009

I have problem with Civil3d 2010, when i open heavy drawing or 1 or more drawing will struck out of system memmory cannot continu the drawing , how can i fix, i already install update package 1 & 2 my system config.,and error shown on attached file. a

View 5 Replies View Related

AutoCAD Civil 3D :: 2012 Surface Style Set User Slope Ranges

May 26, 2012

I am grading a parking lot and trying to highlight areas with less than 1% slope.

I can't find the spot to set user slope ranges in the setting tab.

I can find setting number of ranges with three options of minimal use.

This used to be so simple in LDD.

The examples I have seen for this function all show odd ranges of limited value.

View 7 Replies View Related

AutoCAD Civil 3D :: Error Message - Object Was Open For Read

Nov 27, 2008

I very frequently get the above message, "Oject was open for Read". Its to do with annotative text objects which I just recently started using. When I get the message the piece of text I am trying to make changes to is frozen, cant delet it or anything?

View 9 Replies View Related

AutoCAD Civil 3D :: Automatic Parcel Design Error Message

Dec 27, 2013

I'm getting a command line message 'no solution found' when I try and create a slide line in teh Parcel Layout Tools. I have my site boundary and I'm using it to get my reference angle.

View 6 Replies View Related

AutoCAD Civil 3D :: Map Error Message On Save / Autosave Or Publish

Sep 4, 2013

I attached two external DWG using the add source drawings in map, then I queried a single drawing into my current drawing. Which I must admit was pretty cool. However know every time I save, autosave, or Publish I get the message below.

View 9 Replies View Related

AutoCAD Civil 3D :: Event Viewer Error Message When Rebuilding Corridor?

Nov 6, 2013

I'm getting several messages saying "value on wrong side of alignment" when I rebuild my corridor.  I've checked the two target alignments that I'm using and they are on the correct side. 

Civil 3D 2014

View 2 Replies View Related

AutoCAD Civil 3D :: Converting Points Error Message / Invalid Selection Set

Mar 4, 2013

I have a baseplan I was sent for senior design project and it was previously created in an earlier version of autocad. However Im not sure which version it was created in. There are almost 3000 points and contours but I can not use these points to create a surface. I am ultimately trying to create a surface and then a profile for a road to design vertical curves throughout.

I cut out a few points and copied them into a new drawing due to the size of the actual file

View 3 Replies View Related

AutoCAD Civil 3D :: Getting Surface TIN Error

May 16, 2012

We have created a surface made from corridors & breaklines.   During the initial surface creation process the surface appeared to be fine, but as we went thru and started doing edits and adjustments of the corridor the surface is starting to added erroneous points that are created spikes in the surface.   The attached image shows what the surface is doing. 

View 3 Replies View Related

AutoCAD Civil 3D :: Error Message On Running Corridor - Failed Target Not Found

Jul 9, 2013

When I run my corridor I get an error message that says "Failed Target Not Found" it is for the subassembly provided by WisDOT called UrbMedian.

View 4 Replies View Related

AutoCAD Civil 3D :: Tie Feature Line To Surface

Sep 4, 2013

I created a label for retaining wall that takes the z value from the start and end of a feature line. Works great except that it isn't dynamic. I have created the feature line in a grading sheet where the surface is data shortcut into it and I'm just using grips to make sure the ends are on the bottom and top of the retaining wall. Is there any way to dynamically pin/tie the feature line to a surface that has been data shortcut?

View 9 Replies View Related

AutoCAD Civil 3D :: Vertical Surface Error

Oct 25, 2011

if someone can, work with civil 3d 2012, can not do vertical surfaces, do not close properly, what should I do? already re-installed civil and nothing.

View 1 Replies View Related

AutoCAD Civil 3D :: Intersection Surface Error

Apr 5, 2013

My corridor surface randomly bounces from top links to bottom links through the intersections even though I specified top links only and my corridor is modelling correctly.

Previously I just deleted the surface and recreated it with no errors but it doesn't seem to work now. This happens with both manually created intersections and ones created with the intersection tool.

View 9 Replies View Related

AutoCAD Civil 3D :: 2012 Feature Line Crashes?

Apr 6, 2012

AutoCAD C3D 2012 has been crashing nonstop over the past 3 days on me whenever I try to "Create a Feature Line from Object".  I know that it is a localized problem as a co-worker has been in the same drawing and done grading work without any problems.  The error has occurred in multiple drawings. 

Product Version: F.107.0.0. AutoCAD Civil 3D 2012 SP1

View 3 Replies View Related

AutoCAD Civil 3D :: Grade One Surface To Another Like Feature Line?

Jul 12, 2013

I was wondering if there is a way that I can take an existing grade surface and apply a designed pond surface.

Right now I have the pond as a set of 3d Polylines in the proper geometry.

I want to place the pond into this surface and cut/fill at a 3:1 from that pond to the existing surface.

View 9 Replies View Related

AutoCAD Civil 3D :: Elevate Feature Line To A Surface

Jun 6, 2013

This is the message I get when trying to elevate a featureline to a surface in C3D 2012, SP3. The featurlines (4 of them) lie entirely within subject surface but I am unable to get this command (AeccFeatureElevsFromSurf) to complete correctly with any of them.

The 4 featurelines are at the red arrows, a corridor from the centerline at the green arrow has been created, from which the subject surface was derived and is depicted by the yellow & green contour lines.

View 3 Replies View Related

AutoCAD Civil 3D :: Fatal Error On Surface Smoothing?

Apr 25, 2013

I am having an impossible time smoothing a surface created from feature lines in the attached file. I can smooth the service in parts except for the area that I’ve hatched – as soon as I try to smooth that area the drawing freezes or I get a fatal error. Ideally I’d like this surface to smooth to a 3x3 grid.

The things I’ve tried:

-          Exploding the feature lines to 3d polys and recreating them as feature lines before adding them back to the surface.

-          Copying the feature lines to a new drawing and creating a new surface

-          Completely deleting the feature lines and manually re-drawing them from scratch before adding them to a new surface.

-          Adding the feature lines with different supplemental distance and mid-ordinate distances (typically I do 2’ and 0.01’ respectively)

-          Smoothing the surface in sections instead of one global smoothing of the entire surface (it always fails when I get to the hatched area)

-          Smoothing the surface with different grid dimensions.

-          Emailing the drawing to coworkers to see if they can create the surface and smooth it on their computers

-          Combinations of all of the above.

64-bit HP Desktop - HP Z420
Intel Xeon CPU E5-1620 0 @ 3.60 GHz
24GB RAM
AMD Radeon HD 6570
Windows 7 SP1

View 4 Replies View Related

AutoCAD Civil 3D :: Copy Line-work From 2012 To 2009

Sep 26, 2012

I go back and forth between older drawings in 2009 a lot while my current drawings are in Civil 3d 2012.  Is there a way to copy linework from a Civil 3D drawing into my 2009 drawing easily.  I used to be able to copy and paste between drawings but that doesn't work between these versions.  Right now I have to wblock out the linework and open that new drawing and save as 2004 then import it into the old drawing.

View 1 Replies View Related

AutoCAD Civil 3D :: 2012 Content Service Cannot Be Started - Error

Apr 13, 2012

I get the following error (in the event log) when C3D 2012 starts:

Service cannot be started.  The file resolves to a path that is too long.  The maximum length is 260 characters.  [ File name = C:ProgramDataAutodeskContent ServiceServerContentServiceDBConnect.MetaStore.sdf ]

Obviously that path is NOT over 260 characters.

View 2 Replies View Related

AutoCAD Civil 3D :: 2012 Scaling Error When Plotting Profiles

Apr 23, 2012

When plotting profile plan sheets, there is an error in the scaling of the grids.  I can not seem to figure out why the plotter is not plotting correctly.  I did try creating a pdf of the plan sheet and plotting, but still have the same scale error.  It starts to get off scale after about 500 feet, so the error in scale is small, but still there.  It is off by about 2 or 3 feet at 500 feet on the profile grid.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved