My corridor surface randomly bounces from top links to bottom links through the intersections even though I specified top links only and my corridor is modelling correctly.
Previously I just deleted the surface and recreated it with no errors but it doesn't seem to work now. This happens with both manually created intersections and ones created with the intersection tool.
I have a link starting from P1.Is there a way to check if the link is intersecting EG or not?
Civil 3D 2014 x64
Windows 7 64-bit
16GB RAM
How would you show a intersection line showing the intersection of a surface and a level plane or level surface?
Intel Core 2 E8500 @ 3.16Ghz
RAM 8 GB
64 bit
Windows 7 Enterprise SP 1
ACAD Civil 3D 2011
I have 2 roads crossing, and I have created the 2 corridors, and an intersection object created. I split the 2 corridor regions and put the intersection in, and then closed back in the regions to the start of the intersection object (region). Now - how do I make that all one corridor object that reacts to either of my profiles, and is only one corridor surface? - the corridor surface ignores my region boundaries Or at least 3 objects that interact with each other properly. Image 1 highlights the start/end of the corridor regions, and image 2 shows how the surfaces look - why doesn't the corridor surface start and end where the regions do?
View 3 Replies View RelatedCreated intersection added that to existing corridor. Then went to cross section sheets and the cut , fill and strip show up but no subassembly surfaces show for the intersection .
See attached pdf
I am trying to create an intersection design using the Intersection Tools in C3D 2012. I followed the steps in the tutorials, created a corridor on the major road, splitted the regions, created the intersection and added it to the major road corridor, and connect the regions with the intersection portion.
I used the same assembly throughout the design just for simplicity, however, i notice that there are gaps of curb between the curb return section and the through section (as outline in red rectangles).
We have created a surface made from corridors & breaklines. During the initial surface creation process the surface appeared to be fine, but as we went thru and started doing edits and adjustments of the corridor the surface is starting to added erroneous points that are created spikes in the surface. The attached image shows what the surface is doing.
View 3 Replies View Relatedif someone can, work with civil 3d 2012, can not do vertical surfaces, do not close properly, what should I do? already re-installed civil and nothing.
View 1 Replies View RelatedI am having an impossible time smoothing a surface created from feature lines in the attached file. I can smooth the service in parts except for the area that I’ve hatched – as soon as I try to smooth that area the drawing freezes or I get a fatal error. Ideally I’d like this surface to smooth to a 3x3 grid.
The things I’ve tried:
- Exploding the feature lines to 3d polys and recreating them as feature lines before adding them back to the surface.
- Copying the feature lines to a new drawing and creating a new surface
- Completely deleting the feature lines and manually re-drawing them from scratch before adding them to a new surface.
- Adding the feature lines with different supplemental distance and mid-ordinate distances (typically I do 2’ and 0.01’ respectively)
- Smoothing the surface in sections instead of one global smoothing of the entire surface (it always fails when I get to the hatched area)
- Smoothing the surface with different grid dimensions.
- Emailing the drawing to coworkers to see if they can create the surface and smooth it on their computers
- Combinations of all of the above.
64-bit HP Desktop - HP Z420
Intel Xeon CPU E5-1620 0 @ 3.60 GHz
24GB RAM
AMD Radeon HD 6570
Windows 7 SP1
I need an intersection of the surface of a sphere and a plane, producing a circular line.
I do not know how to do that.
I have downloaded ArcGrid (ADF) files from the USGS and am trying to define a TIN surface in Civil 3D with those files. I have done this in the past without difficulty but now I get a fatal error and the system crashes in the middle of the process. The ADF files are large, approximately 465 meg, and cover an entire USGS quad area. Is there any tricks or sollutions that would allow me to use this data source to create surfaces without my system crashing?
The system I am using is a Dell Intel Xeon CPU, W365@3.20GHz with 24 GB RAM, 64 Bit OS.
Just trying to clean up a surface. I can swap edges fine. This project was a 2009 project.
View 1 Replies View RelatedI am working in Civ2010 and want the paste a site surface to my corridor surface. However, when I try to do this, I get an error saying "Error performing edit". I do not know what error is occurring in order to fix it. I have done this with a few other sites within the same drawing and they pasted just fine to the corridor surface.
View 9 Replies View RelatedC3D Version 2012
Surface does exist as we can see the triangles/contours or whatever we choose to display. When we run the Water drop command, we are getting a message saying that the point is outside of the surface. We have selected a valid surface by both picking it visually and selecting it from the dialogue. All layers are on and thawed and we are picking well inside of the surface.
Why it would be telling us that the point is outside the surface?
I am working on a 6 mile highway project whose surface file is 85MB big. So, I created a Data Shortcut of this surface and used this for creating profiles. However, at some locations the corridors go below the surface(as per their original profile) which was not intended. So, I need to restrict the surface to follow the corridors but not go beyond it.
I have created feature lines from corridors and tried to add them as breaklines to the surface. But " error adding breakline" error pops up.
Is it because I am trying to add the breaklines to the mirror surface which I created from Data Shortcut ??
Will it be useful if I copy feature lines to original surface file and add these feature lines as breaklines in that file??
Windows 7 x 64
Nvidia Quadro 2000
24 GB Ram
i7 960 @ 3.20 GHz
Civil 3D 2012
What distinction is between “intersection” and “apparent intersection” in snaps,. I’m not sure what difference is between the “intersection” and “apparent intersection” in snaps.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I've started doing my first intersections but I'm stuck with one mistake. I did all daylights and curb returns for intersection.
I have a feeling that it's incorrect targeting here, isn't?
What is the best way to relocate and intersection (created with the wizard) from 43+00 to 40+50? I dragged the alignment but the return baselines don't seem to come along for the ride. Would it be better to bite the bullet and redo it?
View 3 Replies View RelatedI am "trying" to design a intersection that contains four lane divided road. Northbound and Southbound lanes are 2% normal crown with a curbed median. I have alignments for each crown. The intersecting road is not crowned. This road is a retrofit so I am limited quite a bit so the intersection wizard is out. We're going old school with this one.
View 2 Replies View RelatedI need a style for intersection of alignments that automatically includes the abbreviations for Point On Tangent (POT), Point On Curve (POC), etc. I can create a style with the basic information of Station, Alignment Name, but adding the POT, POST, etc. in front of all alignment’s stationing and name doesn't seem available still in Civil 3D 2011.
View 9 Replies View RelatedI m trying to create an intersection between two roads. See the attached jpeg. When i open the corridor properties i receive an error message which i don't understand. It seems like civil 3d has problem with the order of the regions. Also the corridor sections intersects in the area that i have place a remark "problem". I m trying to correct it manual but when i rebuilt intersection then it overlaps my manual correction
View 3 Replies View Relatedissue with my Corridor. It involves the intersection of a main road alignment and a secondary road. Thing is my main road has a 6' shoulder whereas my secondary road doesn't have a shoulder at all. I used the Intersection Wizard to create the Intersection, but the two templates don't align. Without the shoulder the ditches don't line up. I tried drawing a polyline between the two ditches and targeting it and that worked, but then realized that going from 6' shoulder to no shoulder wasn't working either so when I tried to target a polyline from the 6' shoulder to the edge of pavement all kind of stuff happened that didn't make sense to me.
Windows 7 Prof w/ SP1, 64bit, Xeon 3Ghz, 16GB
Civil 3D 2013
I have a site access road that extends from highway into site and then loops around and intersects with itself. Would like to keep this as one alignment in order to make Super Elev and master alignment easy to control across project team.
Issue is, we would like to use Intersection wizard at the intersection but cannot, as we ony have one alignment. We could model the intersection the old way, using kerb returns with design profiles, but as the design is still in early stages the intersection is likely to be frequently revised.
how we could utilise intersection wizard in this scenario?
C3D 2010 user
I have a problem modeling intersection. This is first time I am modeling intersection. I have gone thru' and actually did all intersection tutorials offered by C3D and naturally I felt like I am ready for it.
But in real world I am not. I am trying to model intersection and I keep getting error as "Value on Wrong side of alignment to profile". I looked at target mapping and thinks so that all is okay (may be not). I am attaching snapshot of error message as well as plan view. I wanted to forward actual dwg but size is too large to post.
Point to note:This is Left lane driving setting. I realized this after I created alignment/profile/assemblies but before I tried intersection modeling.
I did 8 iterations before this post.
I would like to know how it would be possible to manipulate the Intersection Wizard so that I can obtain the required shape as drawn by the architect. In essence create a "round about" shape. see the attached image for furhter detail.
View 4 Replies View RelatedCreating an intersection of two roads. I have created corridor using alignments, profiles and assemblies. then i have created the intersection. However, i find it quite strange. Maybe it's because of the assemblies. . I am attaching the file herewith .
View 1 Replies View RelatedI have a super-e road assembly as shown that is running into the intersection of a future road stub. I can not figure out how to get the sidewalk to grade out in the intersection transition I have created for the curb return. Any way to get through this situation?
View 2 Replies View RelatedI have a mainline corridor which is intersecting with a side road corridor that is curving towards the mainline. After the PT of the curve, the two alignments are parallel and I am using an offset assembly here for the sections. What is the best way to handle the area where the two corridors are coming together. As far as I've been able to tell, I cannot use an offset assembly through the curve. There will be a ditch between the two that needs to be shown someway or another. I've attached a screen shot.
View 5 Replies View RelatedI think it is not possible but .... Is there any way to reuse the wizard I have customized to create the intersection ?
Civil 3D (2013)
Having issue with the intersection tool for a road widening with turn lane with new roadway intersection. Not repaving entire existing roadway, sawcutting 2' into lane then paving new turn lane. Do most people use intersection tool for road widening, or is it strictly used for new roadways.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
The street is a 'T'. The alignment is extended... Sta 0+00 starts 100' back and the intersection at centerlines starts at 1+00. The alignment is masked between 0+00 and 1+00, but that obviously doesn't make a difference for the intersection wizard.
The intersection wizard does not give me a choice, it just presumes a 4-way intersection. How do a do/choose a 3-way 'T' intersection in this case?
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013