I am working in Civ2010 and want the paste a site surface to my corridor surface. However, when I try to do this, I get an error saying "Error performing edit". I do not know what error is occurring in order to fix it. I have done this with a few other sites within the same drawing and they pasted just fine to the corridor surface.
View 9 Repliesall of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies View RelatedI am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
can you paste a surface from a different dwg?
View 4 Replies View RelatedCan I do that? I want to import a surface from another drawing to my design drawing.
View 4 Replies View RelatedI have one surface (surveyed pts) that I would like to paste onto another larger surface (say a LIDAR or GIS base). The extents of the small surface are entirely within the extents of the larger surface. The small surface does, however, have some interior areas without any data ('holes' if you will). In these areas, I want the paste operation to result in just the original base surface... but the paste operation assumes I want the new composite surface to also have a hole...
Screen shot illustrating attached with example surfaces. Is there a way to paste only the surface and not the holes?
You can copy both the surface and the original (in this case contour polylines) data or only the surface. In both cases paste operation results into a copy of both data and surface.
Ok, But when paste and rebuild, the distance from original base point and destination point is applied in turn to the surface itself. Maybe it is a BUG ?
Civil 3D (2013)
I'm so tired of wasting time cleaning up holes in surfaces using the surface edit tools.
For some reason when i'm using the add line tool, i need to click the same two points 6-10 times before it actually closes or even more frustrating; it just doesn't close. When I review the event viewer error, it says cannot add / crossing break line... This isn't true, there are no breaklines being crossed.
I am trying to change settings in my template so that some of the Edit operations are turned OFF by default in newly created surfaces. Right now all of these options are turned on for each new surface. The command settings for CreateSurface allows me to control the build options for new surfaces, but I cannot find anything for edits.
View 1 Replies View RelatedI have a surface that I created by joining to surfaces, and now I want to reduce my boundary, how can I edit it?
windows 7, intel I7, 8 MB RAM, civil3d 2013.
Is it possible to edit a surface imported from LandXML with additional survey information (points and figures)? I would assume the tin could be edited and the new data included in the surface.
C3D 2011 (latest updates)
Win 7 Pro, 64-bit
16 GB RAM
When I try to paste in any collection of cells from excel using "paste special" C3D crashes. I'm using 2010. It crashes trying to paste into any drawing, and any group of cells.
My error is:
Unhandled Access Violation Reading 0x209519f8 exception at 478f56h
I am currently using Civil 3D 2013, and when I do a qsave, my drawing gives me the following error dialogue box.
"Drawing File is Write Protected" - I am the only on in the files, so now my file is currently Read Only - then I am able to re-open the same file as the same time I have the currently read only version open.
I am getting this currently after or during Plan Production, creating sheets, and I do a qsave.
I am using Civil 3D 2013 Hotfix 1
Windows 7 64 bit system
12GB Ram
Quad Core Xeon 3.2
Server is using Microsoft Server 2008
We have created a surface made from corridors & breaklines. During the initial surface creation process the surface appeared to be fine, but as we went thru and started doing edits and adjustments of the corridor the surface is starting to added erroneous points that are created spikes in the surface. The attached image shows what the surface is doing.
View 3 Replies View RelatedI have a proposed surface that has been made by selection polyline with a z elevation as contours. Is it possible to have civil 3d easily change the weeding and supplementing factors to a tighter value after it has already been made?
View 1 Replies View RelatedI was trying to edit a corridor surface manually by editing points and tin lines but for me its much easier to edit the contours itself so I explode the surface into polylines and fix the contour issues but when i make it into a new surface the Surface does not look clean anymore. When I look at it in the object viewer it looks rough and jagged and doesn't look like a road at all, however my original corridor surface did look clean with perfect roads and cul de sacs i just wanted to fix the contours outside the road. I tried extracting it like i should have done in the first place but when i add the contours to a surface it still looks ugly and jagged. Another thing is that when you look at it in 2D or plan view the contours look exactly the same but when i look at it from a perspective view or 3D that's when you see the difference.
View 3 Replies View Relatedif someone can, work with civil 3d 2012, can not do vertical surfaces, do not close properly, what should I do? already re-installed civil and nothing.
View 1 Replies View RelatedMy corridor surface randomly bounces from top links to bottom links through the intersections even though I specified top links only and my corridor is modelling correctly.
Previously I just deleted the surface and recreated it with no errors but it doesn't seem to work now. This happens with both manually created intersections and ones created with the intersection tool.
I am having an impossible time smoothing a surface created from feature lines in the attached file. I can smooth the service in parts except for the area that I’ve hatched – as soon as I try to smooth that area the drawing freezes or I get a fatal error. Ideally I’d like this surface to smooth to a 3x3 grid.
The things I’ve tried:
- Exploding the feature lines to 3d polys and recreating them as feature lines before adding them back to the surface.
- Copying the feature lines to a new drawing and creating a new surface
- Completely deleting the feature lines and manually re-drawing them from scratch before adding them to a new surface.
- Adding the feature lines with different supplemental distance and mid-ordinate distances (typically I do 2’ and 0.01’ respectively)
- Smoothing the surface in sections instead of one global smoothing of the entire surface (it always fails when I get to the hatched area)
- Smoothing the surface with different grid dimensions.
- Emailing the drawing to coworkers to see if they can create the surface and smooth it on their computers
- Combinations of all of the above.
64-bit HP Desktop - HP Z420
Intel Xeon CPU E5-1620 0 @ 3.60 GHz
24GB RAM
AMD Radeon HD 6570
Windows 7 SP1
I have downloaded ArcGrid (ADF) files from the USGS and am trying to define a TIN surface in Civil 3D with those files. I have done this in the past without difficulty but now I get a fatal error and the system crashes in the middle of the process. The ADF files are large, approximately 465 meg, and cover an entire USGS quad area. Is there any tricks or sollutions that would allow me to use this data source to create surfaces without my system crashing?
The system I am using is a Dell Intel Xeon CPU, W365@3.20GHz with 24 GB RAM, 64 Bit OS.
Just trying to clean up a surface. I can swap edges fine. This project was a 2009 project.
View 1 Replies View RelatedC3D Version 2012
Surface does exist as we can see the triangles/contours or whatever we choose to display. When we run the Water drop command, we are getting a message saying that the point is outside of the surface. We have selected a valid surface by both picking it visually and selecting it from the dialogue. All layers are on and thawed and we are picking well inside of the surface.
Why it would be telling us that the point is outside the surface?
I am working on a 6 mile highway project whose surface file is 85MB big. So, I created a Data Shortcut of this surface and used this for creating profiles. However, at some locations the corridors go below the surface(as per their original profile) which was not intended. So, I need to restrict the surface to follow the corridors but not go beyond it.
I have created feature lines from corridors and tried to add them as breaklines to the surface. But " error adding breakline" error pops up.
Is it because I am trying to add the breaklines to the mirror surface which I created from Data Shortcut ??
Will it be useful if I copy feature lines to original surface file and add these feature lines as breaklines in that file??
Windows 7 x 64
Nvidia Quadro 2000
24 GB Ram
i7 960 @ 3.20 GHz
Civil 3D 2012
I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011
I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.
The questions:
Would it be better to import the surface into Revit to merge surface and buildings together?
Would it be better to import the buildings into C3D to merge entities?
Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?
I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.
i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline. This seemed to work, but when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.