I am trying to change settings in my template so that some of the Edit operations are turned OFF by default in newly created surfaces. Right now all of these options are turned on for each new surface. The command settings for CreateSurface allows me to control the build options for new surfaces, but I cannot find anything for edits.
View 1 RepliesI am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
I'm so tired of wasting time cleaning up holes in surfaces using the surface edit tools.
For some reason when i'm using the add line tool, i need to click the same two points 6-10 times before it actually closes or even more frustrating; it just doesn't close. When I review the event viewer error, it says cannot add / crossing break line... This isn't true, there are no breaklines being crossed.
I have a surface that I created by joining to surfaces, and now I want to reduce my boundary, how can I edit it?
windows 7, intel I7, 8 MB RAM, civil3d 2013.
Is it possible to edit a surface imported from LandXML with additional survey information (points and figures)? I would assume the tin could be edited and the new data included in the surface.
C3D 2011 (latest updates)
Win 7 Pro, 64-bit
16 GB RAM
I am working in Civ2010 and want the paste a site surface to my corridor surface. However, when I try to do this, I get an error saying "Error performing edit". I do not know what error is occurring in order to fix it. I have done this with a few other sites within the same drawing and they pasted just fine to the corridor surface.
View 9 Replies View RelatedI have a proposed surface that has been made by selection polyline with a z elevation as contours. Is it possible to have civil 3d easily change the weeding and supplementing factors to a tighter value after it has already been made?
View 1 Replies View RelatedI was trying to edit a corridor surface manually by editing points and tin lines but for me its much easier to edit the contours itself so I explode the surface into polylines and fix the contour issues but when i make it into a new surface the Surface does not look clean anymore. When I look at it in the object viewer it looks rough and jagged and doesn't look like a road at all, however my original corridor surface did look clean with perfect roads and cul de sacs i just wanted to fix the contours outside the road. I tried extracting it like i should have done in the first place but when i add the contours to a surface it still looks ugly and jagged. Another thing is that when you look at it in 2D or plan view the contours look exactly the same but when i look at it from a perspective view or 3D that's when you see the difference.
View 3 Replies View RelatedJust installed C3D on my Dell POS Windows 7 machine (OS is up to date).
I have noticed that the functionality between using the F3 and F8 keys reverses itself when first used. If I hit F3 I turn Ortho ON/OFF. If I hit it again, I turn Osnap ON/OFF. If I do the F3 key, then do it again to get the Osnaps set how I want, then go to the F8 key to set the Ortho mode back to where it was before I hit F3, it changes my Osnap setting, and I end up chasing my tail around and around. I can use the SCREEN buttons down below my working area. but I prefer keys, finding it far easier to hit F3 without even having to look at the key board rather than put my cursor over the little square of turn Osnaps ON/OFF there.
C3D 2012..In some drawings I can set the Default Styles in the point creation box.Some drawings it's greyd out and won't let me change the default.
View 2 Replies View RelatedI'm tweaking out dwt file and I am noticing that the default lable and pipe style I have set in the network defaults is not being honored.
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
When I create a report from 'Staion offsets to points' to excel, the Station, (what I would call chainage) is coming up as 3+10.00 in the spreadsheet. I need this to be 310.000 so I can apply formulas in excel. How do I change this.
I've changed the alignment label style to show it as this format, and it works fine. I've also gone into 'Edit report settings' and changed alignment station display to ####, decimals to 3 places, yet it keeps giving me the same format with 2 decimals.
Also, in this report, how do I remove the metre symbol 'm' (i.e 1400m) from the offset and elevation display?
I need to create an excel spreadsheet with quite a lot of data, apply formulas, and I really don't want to remove every 'm' and rewrite every chainage.
Every time I create a new layer, name it, asign a color, linetype, etc...it defaults back to the original color, making me set it twice. Am I missing a setting somewhere?
View 2 Replies View RelatedI have quite a few alignments to create and would rather not have to set the layer and conversion options for each. I'd like all to be on the same layer (that is already defined in the drawing) and to change the conversion options both off. I've been looking through the settings table in TS, but haven't found anywhere to change the default layer and conversion option states. Currently, the create alignment from objects defaults are to have alignments on independent layers (Model-Alignment*, where * adds the alignment name as a suffix to the layer name) and both conversion options are on.
View 6 Replies View RelatedI'm not finding where to change the default Description for Creating Cogo points by the Create Points-Alignments>At Alignment Geometry method
The last characters PC, PT RP etc. seem to be controlled by the Drawing Settings>Abbreviations but the Alignment name and stationing is what I'd like to eliminate from the description if possible.
Almost seems hard coded but hopefully I've been looking in the wrong places.
The descriptions are coming in like the caption whether I select Raw or Full description option.
In command settings for Point>Create Points>Points Creation>Prompt for descriptions>Automatic - Object is what I'm using.
What I'm hoping to accomplish is just PC, PT RP etc for description without the find / replace edits I'm currently doing in the exported ascii files.
C3D 2012 SP3 & C3D 2014 SP1
Win 7 Professional 64 Bit
I can't find the setting for setting the default pipe network layers - dialog that opens when I create a network.
I have different utilities, obviously want them on the right layers.
E_WM --> exst. WM layers plan/profile
E_SAN--> exst. sanitary layers plan/profile.
etc.
I have a template drawing I am getting my styles from. where in the template are these things set?
The create points tool window doesn't use the Points Creation options I set for Default Elevation and Description, when go to create a bunch of points I have to key these in for each one. I know if I go and set these in the settings tab they will stick, but I would like for the tool window to work like it implies.
(running C3D 2012 sp4, Win7 64bit, 8GB)
When I add contour data to my surface, I uncheck all the boxes in "Minimize flat areas by:" except "Swapping edges", and I check the "Swapping edges" box. The next time I add contours, I have to uncheck the same boxes, and check the "Swapping edges" box. I can set the default Mid-ordinate distance, etc. but I can't find anywhere in the settings that I can preset the check boxes for minimizing flat areas.
View 8 Replies View RelatedI often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011
I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.
The questions:
Would it be better to import the surface into Revit to merge surface and buildings together?
Would it be better to import the buildings into C3D to merge entities?
Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?
I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.
i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline. This seemed to work, but when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies View RelatedMy problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies View RelatedI am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
I was wondering if there is an easy way to trim one surface to another. Right now, I have two slopes (3:1) that are perpendicular to each other. They meet at a corner and I have extended them past each other so that I could see the intersecting edge. Now I would like to trim them to each other like you would a polyline etc... but I am not sure how to do this.
If I select surf trim, it tells me they are the wrong object type, but they are tin surfaces?
I used a 2d polyline to create a surface boundary for a surface created. The polyline is a closed loop. For the boundary type it is outer, unchecked Non-destructive breakline, and mid-ordinate distance = 1.
My problem is that when I do this I only get a small portion of the surface to show up within my surface boundary. If I don't have a surface boundary the entire drawing surface shows up no problem.
The purple polyline is my boundary and the light blue is the surface created within the boundary.