AutoCAD Civil 3D :: Trim Surface To Another Surface

May 3, 2013

I was wondering if there is an easy way to trim one surface to another.  Right now, I have two slopes (3:1) that are perpendicular to each other. They meet at a corner and I have extended them past each other so that I could see the intersecting edge.  Now I would like to trim them to each other like you would a polyline etc... but I am not sure how to do this.

If I select surf trim, it tells me they are the wrong object type, but they are tin surfaces?

View 5 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: How To Correct / Manipulate Surface To Show Proper Flat Surface

Dec 2, 2011

I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.

The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.

How to correct/manipulate the surface to show a proper flat surface?

View 6 Replies View Related

AutoCAD Civil 3D :: Reduced Maximum Length For Surface Triangles Causes Surface Holes

Oct 22, 2012

Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.

I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.

View 9 Replies View Related

AutoCAD Civil 3D :: Editing Existing Surface Using Edit Surface Command

Nov 14, 2012

I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.

When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.

I select the surface and use the 'edit surface command' in the ribbon, choosing add point. 

When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!

View 5 Replies View Related

AutoCAD Civil 3D :: Volume Bounded By Existing Surface And Design Surface

Dec 10, 2012

My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.

Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.

What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?

how do I shrink labels? Where is it in the settings ; the Align folder had been check.

View 2 Replies View Related

AutoCAD Civil 3D :: Add A Surface To Blank Drawing / Then Upload DEM Files To Surface

Oct 2, 2012

I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.

The surface imports correcty, but when I try to import  points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.

View 9 Replies View Related

AutoCAD Civil 3D :: Change Reference Surface For Surface Elevation Label

Apr 4, 2012

Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.

C3D 2011

View 1 Replies View Related

AutoCAD Civil 3D :: Import Surface Into Revit To Merge Surface And Buildings Together?

Jul 29, 2013

I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.

The questions:

Would it be better to import the surface into Revit to merge surface and buildings together?

Would it be better to import the buildings into C3D to merge entities?

Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?

View 6 Replies View Related

AutoCAD Civil 3D :: Creating Subset Surface From Main Surface

Sep 15, 2013

I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.

i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline.  This seemed to work, but  when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.

View 3 Replies View Related

AutoCAD Civil 3D :: Create Cut Fill Surface From Existing Surface

Mar 1, 2013

Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.

The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.

I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.

1. Novapoint is quite unstable and crashes alot

2. You cant create profiles out of 3d faces

3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface

4. A large surface made out of 3d-faces demands alot of computer power 

So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Will Not Paste Into Empty Surface

Mar 26, 2012

all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?

View 2 Replies View Related

AutoCAD Civil 3D :: Can't Use The Corridor Surface As DATUM Surface

Feb 7, 2013

My problem added with pic ... I want to make volume calculate for sample road project. When I try to  compute materials I cant use Corridor surface for DATUM... There is only target surface on option..

View 2 Replies View Related

AutoCAD Civil 3D :: Adding Corridor Surface To EG Surface

Mar 6, 2012

I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.

I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.

View 3 Replies View Related

AutoCAD 2010 :: Use Of Surface Trim Command

Jun 21, 2012

I'm working on this model and I am trying to use the surface trim command in cad 2011, but its not working and its pissing me off. I want to use the trim and use the dome in my model as the cutting edge to cut the parts of the curved walls that fall inside the dome but it is not working. I have the file uploaded.

View 1 Replies View Related

AutoCad :: Can Trim LINE To LOFTED Surface

Jun 30, 2012

Can you create a wireframe mesh consisting of lines or splines out of lofted surface?

View 3 Replies View Related

AutoCAD 2013 :: Trim Surfaces To Get Outer Surface

Jun 24, 2013

I m working in autoCAD'13. I have got this drawing from a client. I need to trim these surfaces to get only the outer surfaces. But since these are not intersecting at right angles, i m not able to trim these surfaces. 

Please find attached a small part of the concerned drawing. The intersecting surfaces in the drawing have to be trimmed.

View 9 Replies View Related

AutoCad 3D :: Cannot Trim Extra Portion From Fillet Surface

Feb 19, 2013

I am trying to make a 3d model in autocad. But I have stuck in a problem. When I fillet the surface then I can not trim the extra portion. I am attaching the dwg file. I use autocad 2012.

Trim problem.dwg

View 7 Replies View Related

AutoCad 3D :: Either Subtract Or Surface Trim Corners Of Cylinder?

Feb 2, 2012

I am working on the attached file. I need to either subtract or surface trim the corners of the cylinder but when I try to do either some other surfaces that i did not select get trimmed. 6.dwg

View 4 Replies View Related

AutoCad 3D :: Trim Splines At Intersections With Solid / Surface Elements

Nov 27, 2012

How to trim or break the splines at the intersections with solid or surface elements. I need only the parts of the line that can be seen in the given example.

View 4 Replies View Related

AutoCad 3D :: Trim One Side Of Circular Surface By Using Projected Line

Nov 21, 2011

I am trying to trim one side of a circular surface by using a projected line that forms my trimming line. The original surface is simply a circle that is swept along a path (like a tube/cylinder). When trimming by using the projected line it wants to cut all the way through the surface (i.e. both sides of the tube/cylinder) but I only want it to cut out one side. Is there a way of allowing this or do I create two semi-circular surfaces, therefore only cutting/trimming in effect one side?

View 2 Replies View Related

AutoCAD Inventor :: Trim Curved Sheet Metal To Conical Surface

Nov 20, 2013

I am drawing a fan wheel. The fan blade is curved intersects the shroud, consisting of two cones. I do not know how to trim the blade to the cones. I tried to "split" the blade at the cones and then "delete face" but then the "Go to flat pattern" section on the ribbon is missing. If I suppress the "delete face" feature the "Go to flat pattern" re-appears.

View 1 Replies View Related

AutoCAD Civil 3D :: Surface Boundary Only Showing Portion Of Surface Within The Boundary

Oct 24, 2012

I used a 2d polyline to create a surface boundary for a surface created.  The polyline is a closed loop.  For the boundary type it is outer, unchecked Non-destructive breakline, and mid-ordinate distance = 1.

My problem is that when I do this I only get a small portion of the surface to show up within my surface boundary.  If I don't have a surface boundary the entire drawing surface shows up no problem.

The purple polyline is my boundary and the light blue is the surface created within the boundary.

View 3 Replies View Related

Maya Modeling :: How To Close Nurbs Surface Edges After Trim

Nov 14, 2011

I've been modelling in Maya for less than a day so go easy on me!

I'm in the process of making a traffic light and have got a bit stuck on the shade around the light.

I first made a profile curve and revolved it to get a kind of cup shape. The profile curve double backs on itself so the revolve is not completely flat.

Next I projected a curve onto the side of the revolve to get the wavy shape of the light shade, and trimmed the excess off.

Now I have my lovely traffic light shape, but the ends where the revolve was trimmed are not attached. (Because I double backed the profile curve)

Is there any way I can close up this gap?

(I've attached some screenshots).

View 4 Replies View Related

AutoCAD Inventor :: Curved Surface - How To Increase Volume Of Surface At Certain Points Only

Apr 10, 2013

how I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.

Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .

At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer

But how can this be done on surface that is curved? Or multi curved for edges?

View 9 Replies View Related

AutoCad 3D :: How To Put Planar Surface To Solid Object Which Surface Is Curved Like Cylinder

Sep 2, 2013

I would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?

View 9 Replies View Related

AutoCAD Inventor :: Ribs On Curved Surface / Trimming To Complex Surface

Feb 28, 2013

I'm designing a press for a skateboard similar to: Rib Press

I have the board modeled: (see attached)

Now what i want to do is generate those ribs as seen in the picture.

I tried creating a block that intersected with the board and tried to split the rib at the surface, but to no avail. I think the issue has something to do with the curve of the board in two directions, but i can't seem to get it right.

if you are having trouble visualizing what i'm asking about, look at this. I want to be able to figure out the exact shape of those center ribs to print and eventually cut out of wood.

View 9 Replies View Related

AutoCAD Inventor :: Extend Button Flat Surface Diameter 12.5 Upto Shaped Surface

May 31, 2012

It is not possible forme to add the fil because it is to large 1.8MB how can I poste then I like to know if it is possible to extend the button flat surface diameter ø12.5 up to the shaped surface. The result should be a total solid block whit a surface shaped hole.

File last up-date with Autodesk Inventor Professional 2013

View 6 Replies View Related

AutoCAD Inventor :: Extrude Feature And Select Part Surface For New Sketch - Offset Surface?

Dec 9, 2011

I am a beginner when a extrude a feature and select a part surface for new sketch now i want is to offset that surface but i can,t there is + sign with mouse icon and something like fully constrained is written in down the window.

View 9 Replies View Related

AutoCAD Inventor :: Merge Flat Surface To Circular Surface?

Dec 6, 2012

I am trying to merge the gaps left from extruding a flat surface off a circular surface, delete face and heal does not appear to work.

Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)

View 2 Replies View Related

AutoCad 3D :: Make Curved Surface A Flat Surface?

Oct 19, 2011

If you look in the attached PDF, I have an elliptical wall that also has changes in elevation. call it a compound radius if you will. What I have to do is to make a wall cap to go on top of the wall. I know, sounds fun.....I have the surface on the right of the PDF and i need to figure out how i can take that shape and have it lay flat so that i can cut this shape out on my CNC. i know I can use the FLATSHOT command, but this will not give me the true shape of the board.

View 4 Replies View Related

AutoCad 3D :: Turn Surface Into Planar Surface

Jul 8, 2008

I know there is a procedure to turn a surface into a planar surface, but i don't really know if autocad can do that, or how to do it. By this procedure i mead transforming a cone into a surface, a cilinder into a surface for example, but in my case the main surface is not a basic surface (as show in the image) and the procedure is quite tricky.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved