I am drawing a fan wheel. The fan blade is curved intersects the shroud, consisting of two cones. I do not know how to trim the blade to the cones. I tried to "split" the blade at the cones and then "delete face" but then the "Go to flat pattern" section on the ribbon is missing. If I suppress the "delete face" feature the "Go to flat pattern" re-appears.
View 1 Replies
Can a curved section with bend be applied to sheet metal part.I make extrusion for easier clarity.I am wanting to place the curved section (extrusion for demonstration purpose) with bend in sheet metal part but all created in the sheet metal environment.
View 6 Replies View RelatedHow to curve a piece of sheet metal over the outside curved edge of the attached part. I can do it the old fashioned way but was wondering if it could be done in sheet metal which would give me the flat pack automatically (that way there is less chance for errors). There are several of these baffles joined together by a spine and the sheetmetal will eventually go over all of these, and have a few modifications to shape the end profile.
The outer curve is a spline which has changing radius and hence to use a contoured roll would be rather difficult and time consuming (there are also some flat sections at each end of the curves as well).
Autodesk Inventor Professional Student 2013 is the version I'm using.
How do you most easily do a sheet metal plate that needs to follow a surface?
L1 is less than L2, and a radius of the plate?
In Inventor 2012
I have 2 sheet metal parts, both have been revolved using an angle of 359.9deg so there is a small gap to weld. in the assembly I copied one as a surface onto the other part and I want to scuplt it at the intersection of the two.
The problem I've come to is that the small gap in the surface is preventing me from deleteing the upper part of the cut, how can I make the surface a whole so there is no gap in the cut?
Is there any way / trick to wrap a 2D sketch to a non-flat/cylindrical/conical face? See attached part. I'd like wrap the lines in Sketch2 to the ring's outer face in order to get a proper path for "engraving". I see no other way to get a proper path for sweep, because project along vector won't work.
View 2 Replies View RelatedI have the German version of Inventor 2014, so some translations may be different.
I want to project a text on a sketch onto a conical surface. The error message is that the chosen surface wasn't tangential to the profile plane. I found no way to rotate the plane.
How do I project my profile onto the conical surface or How do I make the profile plane tangential to the conical surface?
I want to extrude a big number of pillars to a rather complicated surface and that works out fine. But each end of the pillars warps around the surface and I want them just to go up to it and stop with a resulting horizontal face.
View 1 Replies View Relatedhow I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.
Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .
At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer
But how can this be done on surface that is curved? Or multi curved for edges?
I'm designing a press for a skateboard similar to: Rib Press
I have the board modeled: (see attached)
Now what i want to do is generate those ribs as seen in the picture.
I tried creating a block that intersected with the board and tried to split the rib at the surface, but to no avail. I think the issue has something to do with the curve of the board in two directions, but i can't seem to get it right.
if you are having trouble visualizing what i'm asking about, look at this. I want to be able to figure out the exact shape of those center ribs to print and eventually cut out of wood.
A collegue asked me about this as he has been given a part to model and the details are for the flat sheet not the finished model. Is this possible in 'sheet metal'? I had a quick play but couldn't work it out. Im used to creating the finished part and 'un-folding' to get the flat pattern.Detail supplied below.
View 4 Replies View RelatedI'm loft retarded. What I did here was loft to a tangent work plane, then did a sketch on the top surface and extruded the shape that I want. There has to be a better & easier way.
View 9 Replies View RelatedBasically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
I have tried, such as creating lines in a 3D sketch and projecting the geometry to surface, and creating a work plane, and both don't seem to work for me.... I'm trying to cut out a 5.8mmx14mm rectangle out of a cylinder. When I project the geometry to the cylinder's inner surface, I cannot trim the solid in order to extrude. I've attached the file.
View 9 Replies View RelatedI have a cylinder that has for lack of a better word, a zig zaged slot milled into the outside of it thru to the bore. I am unsure how to go about drawing this so I can get it to extrude correctly around the part.
From other cad software history, I could draw it on a straight plane and tell it wrap around the part of whatever diameter. But, since I have not attempted this in Inventor I don't know if this exists.
Just for reference, this is a twist lock device. Turn the cylinder, advance a key the is inside the zig zag advancing or retracting the part that is inside the bore attached to said key.
I just what to cut a sheet metal,
and I don't know how (see in Capture.JPG where i what to cut, and test.iam what I what to cut).
Where is the icon "project the geometry" ?
I am trying to design a new mold for some sailing rudders I am building. The files I have for the current molds are in the IGS format, which Inventor can open. The current rudders are convex going from the widest part of the foil down to the trailing edge. The goal is to create another model with this flattened. If I were doing this in logic it would be: Find max height, alter foil to be straight from max height to trailing edge. I have tried everything I can do to make this happen with no avail. what would be optimal is if I could get it set up so that I can easily control the amount of convexness to the aft section, but the primary goal is to just get it to be straight. The trailing edge is the straighter one.
The final goal is to export to g-code and send off to a cnc.
I have attached the files after I have imported them into autodesk, but below is a link to the original iges files.
[URL]
I am trying to create a simple hole with threads for a set screw on a hub. I cannot figure out how to select the tangent plane I need to create the sketch. I'm using Inventor 2013 and have attached the file below.
View 9 Replies View RelatedHow do I draw ribs on a curved surface. Attached is model that I am working on and I need to create ribs on the curved surface in radial direction. How do I do it?
View 8 Replies View RelatedI'm designing a part, and am having trouble creating a plane tangent to a curved surface. One option for creating a plane says "Tangent to Surface through Point", which in theory I should be able to use, but I can't figure out how to actually place a point there before in order to create a surface at the point.
Basically I am trying to cut a circle into the curved right side of the part
I've attached the part file for reference.
I need a flat pattern for this part but it seems impossible. STEP 2 illustrate the desirable result.
View 7 Replies View RelatedWorking with sheet metal and laying out a pattern for the cnc and was wondering if there is a way to imprint an extrusion onto the surface instead of cutting it. Mainly this will be used for a marking tool so the line type or layer would need to be different.
View 5 Replies View RelatedI am working on a bin type unit, and am having trouble creating a flange, I am creating the bin in the final product stage, then I will separate into manufacturer components. I am having trouble adding this flange around the top 4 edges of the bin. I need the four corners to meet on a miter 45. I will then rip down each seam and have 4 separate panels.
Is this a bad workflow? Is there a better route? I attached the part in Inventor 2013 format,
Attached are two sheet metal parts that we need to unfold and make them flat for a drawing. We cannot seem to capture the reference A or reference B planes asked for by the unfold command.
View 3 Replies View RelatedIs there a way to get the appearance of perforation on a sheet metal tube without having to create each and every hole? Looking for an appearance to drag onto the surface. Kind of like when you make a part look like it is made of brick. It being just an image on the model surface.
View 9 Replies View RelatedVery thin gauge aluminum sheets with a composite sandwiched between them.
The challenge is, the panels are relatively thick, 3mm or 4mm, but a router is used on the fold lines before bending to cut through all but the outer aluminum. This makes for a very tight bend radius.
So, thick 3 layer material, tight bend with mitered corners. Can Inventor's sheet metal tools handle this?
Can this part be made with sheet metal tools...it will be made from aluminum. I attach the shape made with standard tools and the sheet metal attempt.......how do add the sides in sheet metal.
View 4 Replies View Relatedhow incredible it is that Inventor still does not have a functional normal cut option for sheet metal like Solidworks and Solidedge have long had and I agree. I realize that there are the standard workflows like using derive and thicken to get around this problem. However, for those interested, there is a way to make a normal cut (for laser/cnc) directly in the sheet metal part in many cases. It involves using a sketch to split a face and then using the resulting profile for a thicker/cut feature. I'm always interested in any other methods out there for obtaining normal cuts in complex sheet metal (for a clean dxf export). By the way, Autodesk, do you actually not have any plans of ever adding functionality in this area?
View 4 Replies View Relatedwhat's the best way to make tabs on a rolled round ring. I got it done using unfold/refold option but I can not get sheet metal flat.
View 4 Replies View RelatedI am using IV ultimate 2013
just found about this add-in:[URL]
But its not working for me:
I ran the installer, created a sheet metal part and hit rebuild all, it did not create any proeprties, also tried to manually create the properteis then hit rebuild, no go.
I also did a search on my hardrive for the ApplicationPlugins, and placed the sheet metal folder in all of them(there were 3) tried again noto.
The add-in also does not appear in the add-in manager.
Or is there different what to get the flat pattern dimensions in 2013
I have just modelled a part with some faces and tried to convert to sheet metal to have inventor make the bends between the faces. However when trying to convert to sheet metal i get the following error message (Autodesk Inventor Professional Tip) - "This model cannot be converted to Sheet Metal because it contains features that have created multiple bodies. In order to convert to Sheet Metal these features must first be removed."
As the picture show the part only has 1 solid. Even when deleting all features except the "base" face I get the same error message or Tip as Inventor calls it.
