I am trying to create a simple hole with threads for a set screw on a hub. I cannot figure out how to select the tangent plane I need to create the sketch. I'm using Inventor 2013 and have attached the file below.
View 9 RepliesI have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
I want to extrude a big number of pillars to a rather complicated surface and that works out fine. But each end of the pillars warps around the surface and I want them just to go up to it and stop with a resulting horizontal face.
View 1 Replies View RelatedIn the attached file I have a curved piece of sheet metal made with the contour flange tool. All I want to do is put a hole in the center of the sheet.
View 3 Replies View Relatedhow I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.
Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .
At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer
But how can this be done on surface that is curved? Or multi curved for edges?
I'm designing a press for a skateboard similar to: Rib Press
I have the board modeled: (see attached)
Now what i want to do is generate those ribs as seen in the picture.
I tried creating a block that intersected with the board and tried to split the rib at the surface, but to no avail. I think the issue has something to do with the curve of the board in two directions, but i can't seem to get it right.
if you are having trouble visualizing what i'm asking about, look at this. I want to be able to figure out the exact shape of those center ribs to print and eventually cut out of wood.
I need to make a label for a cup but haven't been able to. how to do it (theoretically), I don't how how / if I can use CorelDRAW to do it. I have included the video I used to find out how to do but it uses a different program that uses a "mould tool". Is there a tool that does the same thing on CorelDRAW?
[URL]
I've been working on creating a sword in 3D Max for the last couple of days and have run across a problem. At the base of the blade, it goes up straight for about an inch and then tapers out and up another half inch in a curve.From there, the blade tapers/curves back in, then out once more to create a thicker end of the blade, width wise. I need to know a simple way of doing those curves. A friend of mine suggested using quick loops, then individually scaling them to get the curving effect. That just seemed like it took too much time to me, and I thought there must be a simpler way. I tried adding a taper modifier to the selected area, but that didn't really seem to do much, except give the opposite effect that I wanted.
View 4 Replies View RelatedI want to transfer the rotation motion of part 'C' at a pivot point 'D' , to part 'E' which is pivoted at 'F', while the flat surface of the part 'c' is inserted in to hole 'B' of part E. How to give an assembly constrain to hole 'B' with flat surface 'A'
View 2 Replies View RelatedI'm loft retarded. What I did here was loft to a tangent work plane, then did a sketch on the top surface and extruded the shape that I want. There has to be a better & easier way.
View 9 Replies View RelatedBasically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
I have tried, such as creating lines in a 3D sketch and projecting the geometry to surface, and creating a work plane, and both don't seem to work for me.... I'm trying to cut out a 5.8mmx14mm rectangle out of a cylinder. When I project the geometry to the cylinder's inner surface, I cannot trim the solid in order to extrude. I've attached the file.
View 9 Replies View RelatedI have a cylinder that has for lack of a better word, a zig zaged slot milled into the outside of it thru to the bore. I am unsure how to go about drawing this so I can get it to extrude correctly around the part.
From other cad software history, I could draw it on a straight plane and tell it wrap around the part of whatever diameter. But, since I have not attempted this in Inventor I don't know if this exists.
Just for reference, this is a twist lock device. Turn the cylinder, advance a key the is inside the zig zag advancing or retracting the part that is inside the bore attached to said key.
I am trying to design a new mold for some sailing rudders I am building. The files I have for the current molds are in the IGS format, which Inventor can open. The current rudders are convex going from the widest part of the foil down to the trailing edge. The goal is to create another model with this flattened. If I were doing this in logic it would be: Find max height, alter foil to be straight from max height to trailing edge. I have tried everything I can do to make this happen with no avail. what would be optimal is if I could get it set up so that I can easily control the amount of convexness to the aft section, but the primary goal is to just get it to be straight. The trailing edge is the straighter one.
The final goal is to export to g-code and send off to a cnc.
I have attached the files after I have imported them into autodesk, but below is a link to the original iges files.
[URL]
How do I draw ribs on a curved surface. Attached is model that I am working on and I need to create ribs on the curved surface in radial direction. How do I do it?
View 8 Replies View RelatedI'm designing a part, and am having trouble creating a plane tangent to a curved surface. One option for creating a plane says "Tangent to Surface through Point", which in theory I should be able to use, but I can't figure out how to actually place a point there before in order to create a surface at the point.
Basically I am trying to cut a circle into the curved right side of the part
I've attached the part file for reference.
I need to show fillet welds between the bar and the curved surface. There is a small gap there (3/8" bar against 2 3/4" O.D. tube) and IV and neither groove or fillet weld works. How to show the weld?
I am using IV2009.
I've read the posts pertaining to coil features along curved paths. The existing solutions are limited in that they must rely on a solid with the addition of a bend feature. How can I create a helical surface structure including multiple bends like the one shown?
View 2 Replies View RelatedIn inventor 2013, how do I engrave and wrap some text onto a surface that is neither on a cylinder, a cone, or a sphere? I created the part by first drawing a cross section made up with the spline tool, then revolved it around an axis. I need to imprint two words on the part's curved surface. I sketched the words, then I tried using the emboss/engrave wrap feature, but I got an error message saying that emboss/engrave wrap can only be done on standard surfaces such as cylinders, cones, or spheres. How to engrave words on surfaces other than these standard surfaces? I also tried to extrude cut the words onto the surface, but the words don't wrap to the surface, and are not evenly imprinted onto it.
Also how do i make the letter's bigger when I sketch them? even though I put in large numbers such as 50 in the size box, the text does not appear big. Also, how do I increase the spacing between the letters?
I need to apply a knurled texture to an organic curved surface. It cannot be a decal, this is to be rapid prototyped so the knurl must be real 3d. I have an imported Solidworks file that shows exactly what I need. I do not have access to the author of the Solidworks part so I don't know how they did it. Its part of a pistol grip handle.
Keep in mind that emboss does not support organic surfaces, only cylindrical or planar.
I am just starting with inventor and love the capabilities, which makes me think this is possible. I am creating a cross dowel nut (also called a dowel nut) that looks like a barrel with a threaded hole on the side. This nut is intended to be inserted into wood and connect with a screw. Is it possible to create this cross dowel that also contains the hole surrounding it so when I insert the part into an assembly (a sheet of wood), the hole is created as well?
View 9 Replies View RelatedI'm making a throttle body spacer in 2013 For some reason I can't get a hole made on the side of the extruded side.I place a general point on a new 2d sketch and no luck.
View 7 Replies View RelatedI am drawing a fan wheel. The fan blade is curved intersects the shroud, consisting of two cones. I do not know how to trim the blade to the cones. I tried to "split" the blade at the cones and then "delete face" but then the "Go to flat pattern" section on the ribbon is missing. If I suppress the "delete face" feature the "Go to flat pattern" re-appears.
View 1 Replies View RelatedI am trying to patch up a bunch of small holes in a derived assembly. I've tried going to the options tab that comes up when deriving the part/assembly and plugging in values for the range of hole sizes to be patched, but I get no results when clicking ok. I have scaled down the assembly to 1/10 the original size. I set the range of holes to be patched from 0 to 0.25". The diameter of the holes in the assembly are only 0.017" after scaling down.
Inventor Professional 2013
Intel Xeon W3680 @ 3.33Ghz
12GB DDR3 RAM
NVIDIA Quadro 2000 GPU
Windows 7 Professinal 64-bit
I am trying to make support ribs on a curved plastic surface to make the construction stiffer for a snow puncher.
(Just like on the attached picture, "pic 1".)
But I am having trouble doing this over the curved surface towards the top end of the rib.
As is now I sketch the shape of the rib in both ends and loft it over a sketch (see attached picture, "pic 2"), and then revolve to get the ends.
But this gives problems, result is not good and it's very time consuming.
If this was on a flat surface it would be easier, but now I get a lip along the loft and along the revolve on the top end of the rib.
I'm using Inventor Professional 2013 Student Version.
I am trying to constrin a washer to a curved pipe. How do I create an axis along the curved pipe so the washer can constrain and move along the cruved axis?
View 4 Replies View RelatedI would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
View 9 Replies View RelatedIf you look in the attached PDF, I have an elliptical wall that also has changes in elevation. call it a compound radius if you will. What I have to do is to make a wall cap to go on top of the wall. I know, sounds fun.....I have the surface on the right of the PDF and i need to figure out how i can take that shape and have it lay flat so that i can cut this shape out on my CNC. i know I can use the FLATSHOT command, but this will not give me the true shape of the board.
View 4 Replies View RelatedCreating a linear section view from a curved line
View 5 Replies View RelatedI am designing perfume bottles and for that i need to to repeat a semi circle to repeat over a curved surface fo the bottle. To simplify the problem i have created curved surface and made a semi cirle as a feature, now i want the feature to repeat on the curved surface. I have tried to rectangle pattern, aswell as the circular pattern in all possible ways i can think.
P.s. I have hp I7 processor, 8 gb ram, windows 7 and am using autodesk inventor pro 2013
I keep running into a situation where I would like to be able to create an edge or a work axis at the intersection of a work plane and the surface of the part. I figured out a work around if the surface is flat, but I haven't figured out a work around for a curved surface.
How do I create work axis where work plane intersects curved surface?
Or put another way: How do I project intersection of work plane and curved surface onto the work plane in a 2D sketch?
I need to be able to draw a 2D sketch on the work plane, but get a perfectly matching projected line onto the work plane, from the curved surface, at the intersection of the curved surface and the work plane.
The attached jpg shows the intersection in question. I circled it.