I want to transfer the rotation motion of part 'C' at a pivot point 'D' , to part 'E' which is pivoted at 'F', while the flat surface of the part 'c' is inserted in to hole 'B' of part E. How to give an assembly constrain to hole 'B' with flat surface 'A'
View 2 Replies
How to constrain this flange to the hole in the spherical door. I just can't seem to get the flange to be tangent and I know it can't be as hard as I am making it.
Inventor Pro 2013 (PDS Ultimate)
Vault Pro 2013
Windows 7 64
Xeon 2.4 Ghz 12GB
I have a cone shaped part and would like to put a hole in the curved face. I would like have to hole square to the face in the flat pattern so it can be cut on the plasma table, is there a way to do this? I attached the part with holes in the approximate location.
Windows 7 Pro 64
i7-980X
12Gb ram
GTX460
It is not possible forme to add the fil because it is to large 1.8MB how can I poste then I like to know if it is possible to extend the button flat surface diameter ø12.5 up to the shaped surface. The result should be a total solid block whit a surface shaped hole.
File last up-date with Autodesk Inventor Professional 2013
I am trying to merge the gaps left from extruding a flat surface off a circular surface, delete face and heal does not appear to work.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I'm trying to constrain the green cylinder to move between the red frame. The red cylinder is constrained on the surface of the larger gray cylinder, which moves around the grounded red frame. When the green cylinder goes up hill/down hill the larger gray cylinder is supposed to rotate around its own axis.
When I choose transitional constraint I'm only able to pick one face on the red frame, and not the whole face. I think it's because the face is not planar, but varies in z-led.
Neither am I able to use the Contact Solver, it seems like the friction is too high. The green cylinder doesn't slide that well when using Contact Solver.
I am trying to create a simple hole with threads for a set screw on a hub. I cannot figure out how to select the tangent plane I need to create the sketch. I'm using Inventor 2013 and have attached the file below.
View 9 Replies View RelatedI would like to map an image to the face of Inventor part document. Which possibilities Inventor API offers here? I checked out the ColorMapping example but the tessellation of the flat surface is not sufficient to get high resolution image mapped on it. My intention is to attach images to several parts faces within the assembly environment and this as fast as possible since the scene needs to update very quickly.
PS: I use C#.NET.
Is there any way / trick to wrap a 2D sketch to a non-flat/cylindrical/conical face? See attached part. I'd like wrap the lines in Sketch2 to the ring's outer face in order to get a proper path for "engraving". I see no other way to get a proper path for sweep, because project along vector won't work.
View 2 Replies View RelatedI am building a Crankshaft. How to build the connecting weights that attach the main journals to the connecting rod journals. I can post a screenshot of the design. I have a extruded face that is a half circle on the top.so I am trying to fillet or cut a section off of the rounded edge. I have tried to build tangent workplanes and projecting geomety, but to no avail.
View 9 Replies View RelatedI often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
I created an iLogic rule that allows in a sheet metal part to the informations Length, widht and area of a flat pattern. This rule run and the iproerties are created (see attachment file).
Now, I will run this rule from an assembly file to create automatically, in all sheet metal components, theses iproperties.
Is it possible ? what must I change in this rule ?
If you look in the attached PDF, I have an elliptical wall that also has changes in elevation. call it a compound radius if you will. What I have to do is to make a wall cap to go on top of the wall. I know, sounds fun.....I have the surface on the right of the PDF and i need to figure out how i can take that shape and have it lay flat so that i can cut this shape out on my CNC. i know I can use the FLATSHOT command, but this will not give me the true shape of the board.
View 4 Replies View RelatedI've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
I have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
Question: Is it possible to control the Hole Dimensions called out on the Hole Chart? As in controling leading/trailing zeros for main hole dim, alt home dim and tolerances? Can you combine the Main Dim with the Alt dim in a single column, separated with parentheses? (same with tolerance?)
View 5 Replies View RelatedI would like to use the hole command to place a hole in a part. When I place the hole it won't allow me to use one of the origin planes to locate the hole from. Can I only locate holes off edges?
View 4 Replies View RelatedI have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies View Relatedi use hole feature names in hole table.
i assign hole names attribute to hole feature but dont get attribute hole table.
how to get hole names in hole table.
While creating holes in a part, a small counter shows (when you click on a point) of how many holes there are.
Programs:
Solidworks (1998-2011)
Autodesk Inventor (R8 - 2013)
Autodesk AutoCad 2D
Autodesk AutoCad 3D
Catia V5
SolidEdge
Anvil (Very old program!)
Pro/E
running an assembly in to the road corridor and creating a surface. i have designed a network of Roads in CIVIL 3d in which whole network is surrounded by a Loop road. The loop road cross fall is unidirectional (2%) and 4.5 wide. I have used LaneOutsideSuperWithWidening subassembly to create the assembly of the road. This doesnt contain any kerb or footpath but only road channel lines, The corridor run soomthly but after creating the of the loop road corridor the surface is becoming flat meaning there isn't any cross fall acoss the road but in the assembly crossfall is there. If i run the same assembly in another road alignment the suface is coming absolutely correct.
I also tried different road assemblies to run along the loop road but the result is same no cross fall across the road.
How would you cut into a flat surface such as a rectangle, to create an opening that is visible in 3D?
View 9 Replies View RelatedI am using Civil 3d 2012 and an trying to apply elevation banding (one color) to a surface that is completely flat. Everything seems to be in order but nothing shows up. If I add another point file to it that has a variety of elevations then the elevation bands show up, if i remove it it disappears again. I can view the boundary and get elevation readings when I mouse over the surface.
View 6 Replies View RelatedI have a drawing like as attached drawing. I must to model 2 flat surface with different elevation and a slope between them.
View 5 Replies View RelatedI am using Autocad 2013. I need to fuse a square building which is placed on a sloping terrain. If the terrain was flat, i would have no problems. But how i can put a perfectly square building on a sloping terrain without having any gaps in between?
View 1 Replies View RelatedI can't find a way to create multi flat patters in one part from a lofted sheetmetal part. Also, didn't the developers fix the 'can't make a flat pattern from a derived part'?
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I would like to shell out this volume. Is there any way to push the flat surface down into the volume to accomplish this? See attachment: Volume.jpg
View 1 Replies View RelatedI am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
I've managed to hack together some code to draw a rectangle and dimension it. Now I want to constrain it to the origin. I figure either using two dimensions from a top/side to the origin and setting the dimension as half of the other respective dimension would work. Or constraining the center point of a top/side line to be vertical/horizontal to the origin.
The problem I'm having is I do not know how to reference the origin. So until I figure out how to reference the origin point I can't use either method.
Public Sub DrawSketchLine() ' Check to make sure a sketch is open. If Not TypeOf ThisApplication.ActiveEditObject Is PlanarSketch Then MsgBox "A sketch must be active." Exit Sub End If ' Set a reference to the active sketch. Dim oSketch As PlanarSketch Set oSketch = ThisApplication.ActiveEditObject ' Set a reference to the transient geometry collection. Dim oTransGeom As TransientGeometry Set oTransGeom = ThisApplication.TransientGeometry Dim oUOM As UnitsOfMeasure Set oUOM =
[Code].......
I've made 2 parts and I'm attempting to constrain them but I can't seem to get it to fit properly.The transition should fit at the opposite end of the 2 square cutouts with the square end of the transition inside the cylinder.
View 7 Replies View Related
