I am trying to get C3D to report the surface area for a bounded area with no success. I am aware of the Bounded Volume feature, which BTW appears to be retired in the 2014 release (AECCCFDBADDBOUNDEDVOLUME fails to produce any results). Obviously there have been some major changes.
What I want to do is retrieve a report for a defined section of a surface, regardless, of what type of surface it is. I see this as simple as deriving the 3D areas of the trinangles within a bounds of a TIN.
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
I've read a few threads on this way back but cannot locate them. I have two surfaces and create a volume surface and it reported the volume as 493 cy. I then ran some sample lines at 25 foot interval and the total volume is reported as 964 cy.
how I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.
Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .
At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer
But how can this be done on surface that is curved? Or multi curved for edges?
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013 MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build) Microsoft Windows 7 64bit 350GB Bootcamp volume
I have a couple of questions regarding surface volumes/analysis in Civil 3D 2014. First, there used to be a way to determine the volume between two surfaces without creating a volume surface. The command is _AeccReportSurfaceVolume, but I can't find it on the ribbons in 2014 to save my life. Do I need to create a new button myself?
Second, and more important, dealing with the elevation analysis in 2014, and noticed that the colors reset anytime that the volume surface is rebuilt? It has always been annoying not to save a color scheme, but at least once you had set it up, the colors stayed as the surface changed. Is there a new setting that I am missing, or is this just a glitch with 2014?
I have a large 200+ acre site that I have created a volume surface and analyzed it using the elevation banding with color to show different levels of cut and fill. The owner has broken this area into 10 different irregular zones. Is there a way to do the elevation banding of a volume surface and have it color the individual parcels. They don't all have to be at once. I can do each one at a time and PDF the drawing.
I have run a volume between two surfaces, I need to further to break that new volume surface up to get volumes for each section. I know in microstation you can fence a volume surface and it will tell you the volume for that area. Is there a function in civil 3d that works like this. I know I can break it up manually and create new surfaces, I am looking for a time saving appoarch and trying to minimize file size.
I can see the area of a TIN surface no worries (under Surface Properties/Statistics/Extended), but want I want to get is surface area of a TIN volume surface where no "extended" option seems to be available to view the area information with this type of surface.
I have a tin volume surface comprised of proposed and existing models for a large earthwork site. I would like a detailed cut fill diagram for presentation to project owner. The site involves cuts and fills up to 30' depths. I would like to be able to represent not only cuts and fills, but give a visual representation of the depth of cuts/fills (ie darker blues and reds in the deeper areas, lighter in the shallow areas). Is there a simple way to do this without setting up 100 different colors of blues and reds in the volume surface properties analysis tab? I have seen contractor software that performs this function rather easily.
First I make surface1 and import the 4 point with elevation 0 sec. I make surface 2 and import 4 point with elevation 1 then itry to find volume of this cube and my result is 0.03 c.meter why this happen.
2) if this above method is wrong give me step by step guide of surface and volume.
I am trying to determine the volume of material (cut/fill) for a roadway surface in C3D 2013 using the volume dashboard.
I have created a fictional surface, basic profile and assembly so I can compare my calcs with C3D. After creating my surfaces and running the dashboard calcs, the program calculated the correct cut/fill volume. However looking at the surface in iso, I saw that additional surfaces were produced around zero elevation - refer to attached snapshot
In my actual model, I am well above zero elevation but these additional surfaces could cause problems on other projects.
I have a pumped storage project where I would like to know the water level if a volume of water is removed. Is there an easier way to do this? Currently I have my drawing set up with my base surface and various top water level surfaces. I have been creating volume surfaces for each TWL and populating a spreadhseet that indicates how volume and surface area differs with TWL. It would be incredibly handy to work this in reverse ie ask the volume surface to lose or gain a required volume of water and update the TWL accordingly.
What I have is a tin volume surface. I am asked to label the points with the thickness of the volume surface.So where there was survey data on the top layer I need to have the width of the surface at those same points.
I'm working in Civil3D 2011. How to export the data from the surface volume tables to excel, or any other format outside of Civil3D?
Or maybe a better question: how to create a stage storage table automatically within Civil3D? The elevations table gives volumes per elevation class, but I'm trying to get cumulative volume stored below various elevations in my reservoir.
how to make a color rendering showing cut and fill on a volume surface. I keep reading bits and pieces of how to do it, but nothing explaining a step by step process. The terminology keeps referencing elevation ranges? I figured out how to create a volume surface, but now desire to print out a colored drawing showing the cut and fill areas.
I need write Cut and Fill Labels on Volume surface in each 10x10 meters. Civil 3D can write Spot Levels on grid, but I need write Cut and Fill values in grid area. Using Surface >Utilities>Bounded volumes I can get the values on selected closed polygon, but write to all is very long work. How to do write Cut and Fill labels on grid.
I created surfaces in Civil 3d 2011 for existing and proposed and I did a surface volume between them. Is it possible to create a specific contour in the volume surface that represents the fill volume elevation (daylight line I think)? My proposed surface is a flood water elevation and I need to define the boundary at that elevation.
see attachment (object viewer capture). The top surface is my OG, the bottom surface is the bottom of excavation for a building. I want to project the perimeter of the building footprint up to the OG surface at a 1:5 slope. I remember in LDD the perimeter of a building, berm, dam, ditch...could be projected to the OG with specific slopes and then you could create a surface with the projected lines and do a volume calc. between the two. What is the procedure to do this in AutoCAD Civil 3D 2012?
I use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.
I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.