AutoCAD Civil 3D :: Generate Volume Report For Bounded Volume Surface?
Oct 2, 2012Is there a way to generate a volume report for a bounded volume surface?
View 3 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: Sample Line Volume Report And Surface Volume Give Different Quantities
Jun 18, 2012I'm working with TIN surfaces, doing cut/fill comparisons for a surface mine.
My volume surface statistics show a cut volume of 5167.22 cy and fill volume of 8456.18 cy.
The sample line group volume report show cumulative cut of 5527.67 cy and fill of 8465.56 cy.
What could be some causes of this disparity. All reference surfaces are built from points and use a non-destructive boundary.
AutoCAD Civil 3D :: Volume Bounded By Existing Surface And Design Surface
Dec 10, 2012My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
AutoCAD Civil 3D :: Cross Section Volume Vs Volume Surface
May 31, 2013I've read a few threads on this way back but cannot locate them. I have two surfaces and create a volume surface and it reported the volume as 493 cy. I then ran some sample lines at 25 foot interval and the total volume is reported as 964 cy.
View 1 Replies View RelatedAutoCAD Civil 3D :: How To Compute Volume Of Material Bounded By Three Surfaces
Aug 16, 2012How to compute volume of material bounded by three surfaces in a section view?
View 1 Replies View RelatedAutoCAD Civil 3D :: How To Modify Volume Report
Sep 13, 2013I would like to re-format the way volume reports are displayed, for example I don't need the cut area or reusable volume columns or I'd like to change the Cu.m. dimensional to something like m3.
View 5 Replies View RelatedAutoCAD Civil 3D :: Corridor Cut / Fill Volume Report?
Jul 11, 2013I have created surfaces for my original ground and my corridor. Both have appropriate boundaryies and the TIN looks good for both. I am trying to create a volume report through Volume Dashboard. I am able to create the volume surface with no issues but the numbers it comes up with do not seem correct. I can see from my profile that there is a small fill but the software seems to create a fill that is almost half of all the material when my profile shows there is more cut.
I tried creating a sample line group...it also shows the majority is cut. The only thing I can think is that there are about a dozen areas where my daylight does not work. how to do this volume correctly?
AutoCAD Civil 3D :: Exporting Volume Dashboard Report From IE To Excel
Apr 9, 2013Just trying to bring in a Volumes Dashboard report from IE10 to Excel 2010 (it all worked fine until I my PC was upgraded from IE9/Excel 2007)
When the report is in IE10, I Select All and paste to Excel (as I always have done) and the numbers are not recognised as numbers (there is no convert text to numbers prompt) and seem to have a leading space which Find/Replace can't find and replace.
If I right click in IE10 and Export to Excel, most of the exported data has a weird character preceding it (but which can be found and replaced). What this character is and how to stop it appearing?
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
AutoCAD Civil 3D :: Corridor Materials List And Volume Report
Nov 6, 2013I am trying to get a material volume report for a corridor structure. The overall dirt cut fill is working, but the pavement and base keeps showing up as zero.
I started with the surfaces made, (perhaps that’s the problem,) I made an alignment, used an assembly, made a profile, and sample lines, made the corridor. The assembly draws in the cross sections, but the materials report shows zero in the pavement and stone.
AutoCAD Civil 3D :: SSA Storage Volume Is Double Of Pondpack Volume
Apr 24, 2013I want to use it as my primary hydrologic and hydraulic modeler. It only makes sense. Well, I got the program to work and had things linked in and was able to route a storm through the network. But when I routed the storms, I had to model double the storage that i expected.
So I went back to the program I'm familiar with - Pondpack by Benltey - and designed the same system I routed in SSA in that program - and got the storage volume that I would expect for a site of this size - about 2 acres.
Is there possibly a setting that I'm missing that makes my outlet structures route slower or less than they should? Or is there some other reason that a system would give this kind of inflated need for storage?
AutoCAD Civil 3D :: Volume Boundary Creates Incorrect Volume
Feb 25, 2013I have an issue with using Bounded Volume or Adding a Boundary to Volume Surface things so bad... = incorrect volumes.. sometimes extremely incorrect.. I understand that the surface rectangle when a boundary is added but this could be horrible if not checked.
View 3 Replies View RelatedAutoCAD Civil 3D :: Surface Volume And Display
Jun 3, 2013I have a couple of questions regarding surface volumes/analysis in Civil 3D 2014. First, there used to be a way to determine the volume between two surfaces without creating a volume surface. The command is _AeccReportSurfaceVolume, but I can't find it on the ribbons in 2014 to save my life. Do I need to create a new button myself?
Second, and more important, dealing with the elevation analysis in 2014, and noticed that the colors reset anytime that the volume surface is rebuilt? It has always been annoying not to save a color scheme, but at least once you had set it up, the colors stayed as the surface changed. Is there a new setting that I am missing, or is this just a glitch with 2014?
AutoCAD Civil 3D :: Surface Volume Analysis
Jan 3, 2014I have a large 200+ acre site that I have created a volume surface and analyzed it using the elevation banding with color to show different levels of cut and fill. The owner has broken this area into 10 different irregular zones. Is there a way to do the elevation banding of a volume surface and have it color the individual parcels. They don't all have to be at once. I can do each one at a time and PDF the drawing.
View 2 Replies View RelatedAutoCAD Civil 3D :: Using A Surface For Volume Calculation?
Sep 25, 2012I have run a volume between two surfaces, I need to further to break that new volume surface up to get volumes for each section. I know in microstation you can fence a volume surface and it will tell you the volume for that area. Is there a function in civil 3d that works like this. I know I can break it up manually and create new surfaces, I am looking for a time saving appoarch and trying to minimize file size.
View 2 Replies View RelatedAutoCAD Civil 3D :: Area Of TIN Volume Surface
Apr 4, 2012I can see the area of a TIN surface no worries (under Surface Properties/Statistics/Extended), but want I want to get is surface area of a TIN volume surface where no "extended" option seems to be available to view the area information with this type of surface.
View 8 Replies View RelatedAutoCAD Civil 3D :: Zero Elevation For Volume Surface?
Sep 27, 2013I'm getting a zero elevation for the surface I create when I compare surfaces to get volumes. What am I missing?
View 9 Replies View RelatedAutoCAD Civil 3D :: TIN Volume Surface Shading?
Feb 10, 2012I have a tin volume surface comprised of proposed and existing models for a large earthwork site. I would like a detailed cut fill diagram for presentation to project owner. The site involves cuts and fills up to 30' depths. I would like to be able to represent not only cuts and fills, but give a visual representation of the depth of cuts/fills (ie darker blues and reds in the deeper areas, lighter in the shallow areas). Is there a simple way to do this without setting up 100 different colors of blues and reds in the volume surface properties analysis tab? I have seen contractor software that performs this function rather easily.
View 9 Replies View RelatedAutoCAD Civil 3D :: Tin Volume Surface And A Fixed Value
Oct 5, 2012I'm have a tin volume surface with contours ranging between -0.240 and 0.000m.
I have a need to display this surface as followed:
-0.220 - 0.000m as -0.220.
-0.240 (-) -0.220 as it is.
I've tried using contour intervals but nothing seemed to happen.
AutoCad 2011 & Civil3D 2011. Product Version 3.
EliteBook 8560w
Intel i7 CPU 2820QM @ 2.3GHz
8 GB RAM
NVIDIA Quadro 1000M
Windows 7 Enterprise 32 Bit
AutoCAD Civil 3D :: Get Vertex From Volume Surface?
Nov 17, 2013Civil 3D API has "TinSurfaceVertex" class and "GridSurfaceVertex" class.
I use those to get vertex:
foreach (GridSurfaceVertex vertice in GridSurface.Vertices) { Autodesk.AutoCAD.Geometry.Point3d punt = new Autodesk.AutoCAD.Geometry.Point3d(vertice.Location.X, vertice.Location.Y,
[Code]....
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
AutoCAD Civil 3D :: Surface Volume Is Wrong
Apr 22, 20121) when I try to find volume of a cube 1*1*1
c3d volume report is 0.03 c.meter why?
First I make surface1 and import the 4 point with elevation 0 sec. I make surface 2 and import 4 point with elevation 1 then itry to find volume of this cube and my result is 0.03 c.meter why this happen.
2) if this above method is wrong give me step by step guide of surface and volume.
3) how to find volume at particular level.?
AutoCAD Civil 3D :: Carriageway Surface Volume
Sep 10, 2013I am trying to determine the volume of material (cut/fill) for a roadway surface in C3D 2013 using the volume dashboard.
I have created a fictional surface, basic profile and assembly so I can compare my calcs with C3D. After creating my surfaces and running the dashboard calcs, the program calculated the correct cut/fill volume. However looking at the surface in iso, I saw that additional surfaces were produced around zero elevation - refer to attached snapshot
In my actual model, I am well above zero elevation but these additional surfaces could cause problems on other projects.
AutoCAD Civil 3D :: Editing Surface By Volume
Jun 12, 2013I have a pumped storage project where I would like to know the water level if a volume of water is removed. Is there an easier way to do this? Currently I have my drawing set up with my base surface and various top water level surfaces. I have been creating volume surfaces for each TWL and populating a spreadhseet that indicates how volume and surface area differs with TWL. It would be incredibly handy to work this in reverse ie ask the volume surface to lose or gain a required volume of water and update the TWL accordingly.
View 3 Replies View RelatedAutoCAD Civil 3D :: Surface And Volume Calculation
Nov 13, 2013I attach picture 1 and 2.
I need to create surface like this picture 2. I need crate surface by joining 1, 2, 3 like as picture 2 section, but when i crating surface its joining as picture.
This problem have been found . I created a tofo of the rock which rock is bend lower picture 2 section to calculate the volume i need the surface create like this.
AutoCAD Civil 3D :: Volume Surface Width Points
Apr 18, 2013What I have is a tin volume surface. I am asked to label the points with the thickness of the volume surface.So where there was survey data on the top layer I need to have the width of the surface at those same points.
Any commands that can make this possible?
AutoCAD Civil 3D :: Export Surface Volume Tables?
Mar 7, 2012I'm working in Civil3D 2011. How to export the data from the surface volume tables to excel, or any other format outside of Civil3D?
Or maybe a better question: how to create a stage storage table automatically within Civil3D? The elevations table gives volumes per elevation class, but I'm trying to get cumulative volume stored below various elevations in my reservoir.
AutoCAD Civil 3D :: Showing A Volume Surface In Color?
Apr 29, 2013how to make a color rendering showing cut and fill on a volume surface. I keep reading bits and pieces of how to do it, but nothing explaining a step by step process. The terminology keeps referencing elevation ranges? I figured out how to create a volume surface, but now desire to print out a colored drawing showing the cut and fill areas.
View 2 Replies View RelatedAutoCAD Civil 3D :: Cut Fill Labels On Volume Surface
Jun 17, 2009I need write Cut and Fill Labels on Volume surface in each 10x10 meters. Civil 3D can write Spot Levels on grid, but I need write Cut
and Fill values in grid area. Using Surface >Utilities>Bounded volumes I can get the values on selected closed polygon, but write to all is very long work. How to do write Cut and Fill labels on grid.
AutoCAD Civil 3D :: Slicing Volume Of Surface At 1m Intervals
Nov 11, 2013We design a lot of Waste storage facilities, mainly above ground level. I need to generate stage storage volumes at one metre intervals. Is there a way to automate this?
View 6 Replies View RelatedAutoCAD Civil 3D :: Surface Volume - Can It Be Broken Down In Different Groups
Jun 18, 2012can i divide them in 3 different areas that when i add their individual volume would give the same total volume if you calculate the entire surface?
View 5 Replies View RelatedAutoCAD Civil 3D :: Possible To Create A Specific Contour In Volume Surface
Mar 2, 2012I created surfaces in Civil 3d 2011 for existing and proposed and I did a surface volume between them. Is it possible to create a specific contour in the volume surface that represents the fill volume elevation (daylight line I think)? My proposed surface is a flood water elevation and I need to define the boundary at that elevation.
View 3 Replies View RelatedAutoCAD Civil 3D :: Project Object To Surface / Volume Calcs
Jul 30, 2013see attachment (object viewer capture). The top surface is my OG, the bottom surface is the bottom of excavation for a building. I want to project the perimeter of the building footprint up to the OG surface at a 1:5 slope. I remember in LDD the perimeter of a building, berm, dam, ditch...could be projected to the OG with specific slopes and then you could create a surface with the projected lines and do a volume calc. between the two. What is the procedure to do this in AutoCAD Civil 3D 2012?
View 5 Replies View Related