Created intersection added that to existing corridor. Then went to cross section sheets and the cut , fill and strip show up but no subassembly surfaces show for the intersection .
See attached pdf
I am at a crossroads with this corridor that I have to create in Civil 3D 2011, with a sub assembly that logically seems very simple...the conditions for daylight can be found in "Proposed Cross Section". In short I have 4 fill conditions and 2 cut conditions, based on height above original ground...(there are additional requirements for guardrails and retaining walls but at this point i will settle for my slope reaching original ground)
View 9 Replies View RelatedThe FG was created from the corridor.
The cross sections show the EG, FG and Corridor. Yet the Corridor is NOT ON the FG surface.
This is only happening on one section (0+20). The other sections look good.
I've read a few threads on this way back but cannot locate them. I have two surfaces and create a volume surface and it reported the volume as 493 cy. I then ran some sample lines at 25 foot interval and the total volume is reported as 964 cy.
View 1 Replies View RelatedI'm not having any luck on my own. Can I use subassemblies that I create in subassembly composer to make an intersection using the "CreateIntersection" command?
View 5 Replies View RelatedIs it possible to add additional cross sections (sample lines added after views were created) to an existing Section View Group?
C3D 2012 SP3 & C3D 2014 SP1
Win 7 Professional 64 Bit
How can i change (smooth transition) my cross slope from +1.952% at St: A to -2.000 % at Station B. In intersection wizard.
View 3 Replies View RelatedAny opinions or tips on using the Intersection Wizard to create an intersection and then editing it to incorporate a spandrel or am I better of not even using the wizard and creating the spandrel from feature lines/alignments?
View 9 Replies View RelatedIn attached file the normal cross slope of secondary road(AB) is 2% Right to left (Right higher). and for primary road cross slope is 2% Left to Right (Left higher). I produced this junction using intersection wizard and cross slope of secondary road only starts changing from start of curb return to match the long slope of primary road. Is this possible to increase this transition lentgh on secondary road to create smooth contours.
View 3 Replies View RelatedIm totally new to max. Im trying to draw a ship hull. I draw frames and placed in positions then i tried applying coss section modeifier and tried also to connect vertices manulay.
View 3 Replies View RelatedI am creating section view with my road project. I successfully created center line alignment, surface, surface profile, sample line and section views on every station I needed on my design.
I want to see "subassembly" (travel lane, curb & gutter, sidewalk, 2:1 slope) on my section view. I can block, insert and copy it to my section my manually, but I know this not the right way to do.
what is the main advantages and disadvantages of these two programs.
Because i actually want to focus of someone of these two programs
I have a link starting from P1.Is there a way to check if the link is intersecting EG or not?
Civil 3D 2014 x64
Windows 7 64-bit
16GB RAM
My corridor surface randomly bounces from top links to bottom links through the intersections even though I specified top links only and my corridor is modelling correctly.
Previously I just deleted the surface and recreated it with no errors but it doesn't seem to work now. This happens with both manually created intersections and ones created with the intersection tool.
Anyway, I'm trying to build a corridor that targets the existing surface with a linkslopetosurface sub. It works just like I want it to, but there are areas where I want to override the target and have it target an existing curb return alignment. Is there a better sub I should be using that will target one first and then a second if the first doesn't work right?
Also, with my corridor section editor, can I adjust the vertical scale to be exagerated? It's really tough to edit the 1:1 ver./hor. scale.
How would you show a intersection line showing the intersection of a surface and a level plane or level surface?
Intel Core 2 E8500 @ 3.16Ghz
RAM 8 GB
64 bit
Windows 7 Enterprise SP 1
ACAD Civil 3D 2011
I have 2 roads crossing, and I have created the 2 corridors, and an intersection object created. I split the 2 corridor regions and put the intersection in, and then closed back in the regions to the start of the intersection object (region). Now - how do I make that all one corridor object that reacts to either of my profiles, and is only one corridor surface? - the corridor surface ignores my region boundaries Or at least 3 objects that interact with each other properly. Image 1 highlights the start/end of the corridor regions, and image 2 shows how the surfaces look - why doesn't the corridor surface start and end where the regions do?
View 3 Replies View Relatedif i have one feature line i want to project to all sections in a sample line group it would seem you should be able to pick the one line and assign in a label style and you would be done quick and easy. instead if you pick the multiple projection option you get this percentage distance box and it tend to grab stuff you don't want.
View 2 Replies View RelatedI have a cross section view with a canal section and a flat water surface section.
Is there a way for C3D to calculate the 2D area of the canal section that is under the water elevation?
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
I'm just starting to get involved with using SSA, and I'm wondering if it's possible to import sample lines/alignments (a la Hec-Ras). I see that there's an irregular channel editor, but no import options that I can see. I'll end up with about a dozen or so x-sections.
View 3 Replies View RelatedI have a band label set up for my cross sections that will show existing grade and finish grade elevations at the 0' offset mark of each section.
However, the band does not show when I create my sections. The only way I can seem to get it to show is by right clicking a section, section view properties, bands tab, click 'import band set' at bottom of window, and select they style i want to use. But I have to do this for each section individually. That is a problem as I have over 200 sections for one piece of this project.
I'm currently working on a cross section plan and was wondering if there was any way I can change the direction of the cross section view. I'm currently just using 2 sample lines, so just 2 views are needed. My problem is that it seems like one cross section...the view is facing upstream and the other sample line, the cross section view is facing downstream.
Is this normal? How come both cross sections don't face the same direction? So with one x section it's in a East-West direction but the other is a West to East direction.
HP Compaq 8100 Elite
Win 7 Pro SP1 - 64Bit
8GB RAM
i7 860 @ 2.80 GHZ
AutoCad Civil 3d 2012 SP1
I am working with cross sections for the first time and have run into a few things I can't seem to figure out. In attachment XSEC CIVIL 3D.pdf you will see how the cross sections currently look in my drawing.
My questions:
1. I cant seem to edit the elevation labels on the right side of the section to match the left side. Where/how can I do this?
2. What is the red line? In some sections it exactly follows the assembly section, but in a few (like this one) it doesn't quite follow. Does this line show where manual editing was done?
3. Where the pavement ends, there is a vertical line which I only want to show on the two pavement layers, it shows all the way thru the assembly. This also happens at the centerline of the assembly and at the edge of shoulder. I figured out how to turn them all off, but I want the edge of pavement vertical lines there.
4. Although the assembly section comes in on color 161 which should plot black for my pen setting, it plots true color. I haven't been able to figure out how to switch this. The second attachment shows a section from a LDD project a few years back which is how I would like this section to plot.
I'm new to cross section in C3D.I'd like to be able to see my existing e/p lines i toped in the cross sections.
View 3 Replies View RelatedI can import my SA fine, but the problem is that the top of it needs to be cut off 1 m above the existing ground (which is already a surface in civil 3d). How do I setup the target surface so that when I import the SA into my drawing, I can link it to that surface and have it cut off 1 m above the surface?
View 5 Replies View Relatedhow to crate Cross section like that below. i can crate data band consten elevetion and offsets. Question is how to crate grid and data like that.
View 5 Replies View RelatedI have my surface, aligment and sample lines created, but I cant get my sample lines profiles.
The grid apperas without data, it is like I have never selected a surface, but I did !
This is what I get , totally empty
create a label style for cross sections that will label the travel way in the run:rise format and will label fore and back slopes in a percent format. I can figure out how to make them all one or the other, but am having trouble getting them to reflect correctly based on where they are attached.I am having trouble coming up with the actual expression or you can do it thru code set styles, but regardless of settings that I change nothing on the cross section view changes.
View 3 Replies View RelatedHow can I project a right of way line into a cross section.
View 1 Replies View RelatedAttached is a pdf showing the issue I'm having with the way elevations labels appear on the outside edges of cross sections.
Issue #1:
I added the dimension to show that the bottom of the cross section is actually at 97.5 but is labeled as 98
Issue #2:
I would prefer the bottom of the cross section to be at an even elevation (98 not 97.5)
I have been asked to place volumes on cross sections with a certain look, that I am not sure if it is possible. For know I am just going to use text, but I would like to come up with a solution for our template and work flow. Below is an attached copy of a markup I have received asking me to show this information on the cross section similar to how he has written it. At this point I only know how to create the tables of to the side. Is it possible to dynamically show this information quickly like shown below? I have a feeling the engineers I work with will not be happy at all with a table off to the side. I am currently using 2013
Civil 3D 2013
HP Z400 Workstation
6GB of RAM
296GB HDD
ATI FirePro V5700(FireGL)
Win 7 Home Professional