As you can see, the nature of my model forbids me from making a 3D solid using LOFT.
The top surface is consisted of 3D polyline and arc, which if "joined" will be become a spline.
The bottom surface can easily be joined into polyline.
If I loft the top and bottom, it'll only give me a LOFTED Surface, which is not I want (wanted a 3D solid).
I have a solid that was created by extruding a regioned profile. I have made a lofted item (Yellow), that I will have to subtract from the solid (Green) to create a hole. When using the subtract command, I recieve the following error.
"The selected surface was ignored. Surfaces cannot be subtracted from solids or regions. At least two solids, surfaces, or coplanar regions must be selected."
I have tried convtosolid as well & to no avail.
I am trying to LOFT multiple ellipse shapes along a spline path to create a door handle. But as soon as I choose 1 section, MAX creates the shape. I cannot figure out how to create the shape with multiple cross sections. I have attached a screen shot and a pic of the door handle I want to create.
View 1 Replies View Relatedlayman what Autodesk is wanting me to change? Trying to use "loft" to skin the surface of 5 polylines. It will do the first, second, third and 5th for a surface, but doesn't like the 4th polyline I created.
View 3 Replies View RelatedI'm having a problem creating a 3D Solid from two 3dpoly lines. I'm attaching a script file which reproduces the two 3dpoly lines to use for the LOFT command. As you can see when running it, I have two closed 3dpoly lines which use exactly the same X,Y coordinates and differ only in the Z axis. I'd like to make a 3D Solid with these lines, which should be possible using the LOFT command... but I only get a surface around the 'sides'.
I needed to remove the .scr extension from the file in order to attach it, so to run it you need to replace .txt with .scr at the end of the filename. It's a standard ASCII script file. If someone prefers I can also give the coordinates of the 3dpoly lines as a post.
i have recived an igs fle which i imported into auticad 2012.when imported the and saved as an .dwg the model is in surfaces, im looking to convert the surface to solid so i can export the file as an .stl for 3d printing. is it possible to convert this?
View 7 Replies View RelatedI've been trying to lay a mesh on top of some contour lines. I've also tried the loft command, but with little success.
I've tried several terrain plugins, but they all seem to malfunction because I have overlapping contours. Here is the dwg, what I'm trying to make.
I cannot figure out how to create a solid surface on top of the retaining walls and also how to grade the transitions for the high to low points of the retaining wall. This would be so much easier for me in Solid Works
Untitled.jpg
How to permanently change the settings of the EXTRUDE command so my polylines, by default, will become a solid instead of a surface object?
View 5 Replies View RelatedIs there a way to create hatching for the slopes surface style instead of using solid colors?
View 2 Replies View RelatedI'm trying to create a 3D solid from four 3d polylines that represent a bridge deck .
If it is not possible to create a 3D solid, can i create a surface?
I have borehole data of a site, where I want to sort of extrapolate the borehole data to the whole site, so that I can have a 3D soil model of the whole site. I have attached my DWG file, the vertical lines represent the borehole data and different colors represent different types of soil.
I'm thinking of manually extrapolating the data to the edges of the site, then split the site area into few different parts, and then create solids for each part, where each point is a vertices of a solid. But how to create a solid from 8 vertices, which would naturally form a closed solid like a box.
Besides this, are there any other methods of achieving what i want (3D soil model from borehole data)?
I'm loft retarded. What I did here was loft to a tangent work plane, then did a sketch on the top surface and extruded the shape that I want. There has to be a better & easier way.
View 9 Replies View RelatedI'm making these legs for a piece of furniture. I need this to be a solid object.
So I drew a vertical line, set the radius using circunferemces. Then (can't remember how, it was long time ago) I manage to turn them into surfaces (circles, so it's an area).
Now when I loft them, it won't result in a solid. Why?
I have a bunch of points that I am trying to turn into a solid object. I am doing this by using the 3D poly command and then LOFT, UNION and CONVTOSOLID. this has previously worked well, but this time when I use the LOFT command it does not produce a 'closed' surface, but rather a grid like surface which wont convert to a solid. Are there different settings for the LOFT command, and if so, How do I change them to produce a closed surface?
View 4 Replies View RelatedI have finally created the shell of the complex surface that you see. This is only a section of the part because I cannot show the whole thing for proprietary reasons. I formed solid surfaces using the network command. The propblem is that it will not convert to a solid because the surface seams are not "water tight." When the network command created the solid surfaces, the surface seams do not exactly match the lines so there are gaps in all the seams. I have tried blending, patching, etc. and nothing works. how to convert this to a solid without losing the outlines and the shape?
View 3 Replies View Relatedhow to loft from 2d sketch to circular surface.
I have attached the model in this model I tried to loft Sketch 6 to Sketch 19.
See attached file.
I have this special type of callout, which is not easy to draft, but it looks pretty in plans. Is there any easy way to convert this to multileader?
Usually, I create it as block, insert it and change location of solid arrow around textbox. If I want to relocate this callout, Its not that easy as like multileader. I have to move solid arrow around textframe (from one corner to other) to point the same location. can this be done automatically (like mleader?)
I have a problem when designing one building in 3d. The thing is i want to create a 3d model made only out of 3d solids. So there is this complex ceiling, I made out of 3 meshes and above it, in the above floor, there's a non complex plate.
[URL] ........
This meshes are made based on the actual dimensions of different sides of the floor, are unique and are good approximation of the actual building's ceiling. So, I want to make 3d solid that would have the same bottom shape and the same - even top as in the picture if the space between the objects would be filled out.
The attached csv file contains x,y,z coordinates and the image number per row (only 1 in this file). I am reading in this file and creating a spline knot at each of these points. The last coordinate x,y,z set closes the splines and creates a shape that resembles a US state. I next extrude it a couple inches and it looks like a hollow 3-D state.
My question is how do I go about capping (or filling) the top and bottom faces? I have a feeling it is a bit more complicated because of the large number of knots, around 127, in this shape. As every time I try and follow the cap surface instructions in the reference it doesn't do what I want. Is there any way to automatically or by using a script join the vertices so that it looks like a mesh grid on the top and bottom and then fill in those areas?
[URL]
I am having problems creating a profile around a path. The profile (image-1) resulted in an undesirable corner (image-2). Which I don't know if that can be fixed. My workaround was to create a lower profile, and then loft between the 2 rails.
The loft results in a twisted surface (image-3). So to correct this under loft> transition I turn off automatic mapping and edit the point set. I always end up with one extra set of points, or edge, and end up having one set of points on top of another, a duplicate edge. Which I believe is where my problem lies. However I can not delete this extra point set, so there is not much I can do there. Am I missing something? This results in a surface loft (image-4). When I thicken this surface by 6mm it results in this broken solid (image-5)
I have tried merging tangent surfaces in the loft command, which appears to work better, but when using thicken the error message reads that the thicken operation did not produce a meaningful result. When I change the thicken direction I get a solid, just not the one that I need.
I had many other strange errors, and seemed to have solved some of them by taking the fillets out the sketch, and applying them to the solid. But this should be an easy operation, and I can't seem to make this work at all.
I am using Inventor 2014 and the ipt file is attached.
Attached is an Inventor 2012 part file. I am trying to perform a surface loft with multiple sketches and rails. Each time I try to perform this operation I get the following error:
Error: The attempted loft operation had problems with the specified rail curve not intersecting one or more sections. Try repairing the rail curve so that it intersects all the sections.
I have corrected this issue as much as I know how by project the rails onto each sketchs workplane and then using the projected points to constrain the sketch. It is not working.
It is very difficult to explain, but I have attached the part file. It was created from Autodesk Inventor 2012.
I draw 3D curved handrail, mainly just rectangular because i import the geometry in to Alphacam and run tool paths down them, but i keep getting faced with the problem of the twisting of a solid when sweeping along a spline or a 3D poly!
View 9 Replies View RelatedI would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
View 9 Replies View RelatedI am trying to create a proposed surface using grading. I created a closed polyline representing the site's outer boundary then created a feature line from it. When I try to select the feature line in order to create the grading I get "THIS FEATURE OVERLAPS ITSELF AND CANNOT BE GRADED".
View 1 Replies View RelatedI'm constructing a simple test track for my university project, and I have managed to get the geometry of the track all sorted. I'm struggling to assign a bitmap image of a 4 lane road surface to the track. When I assign the material all I get is a grey surface with no lane markings. I figured the size may be wrong, but I have tried adjusting the size settings in the co-ordinates roll out in the material editor, with no luck.
A few screenshots are in here [URL]........
I have the following error message:ERROR: Could not create frame surface of window-sectional profile..At various windows and door-window-combinations I added profiles.
View 1 Replies View RelatedI am trying to create a 3d surface by importing points from an excel file. I have been using "import points" in the 3d sketch mode, and checked off the box that says "create 3d spline." But this just causes Inventor to freeze and crash. My excel file had about 2000 points, all of which lie on the surface I want to create in Inventor.
Should this method work in theory, and do I just have too many points?
I am trying to create a 3D meshed surface from an irregular shaped solid I created using firstly a SPLINE, FILLET, PEDIT, and EXTRUDE. I have a solid in the basic shape now, but I am trying to create a meshed top and bottom (x, y, z,) to change the contours of those surfaces. I have looked at 3DMesh but it asks for (n,M,) coordinates like it is a regular shaped surface (square, rectangle) where one can calculate the required even spacing needed.
My goal is to create in CAD something like a fine art carved piece of wood, with irregular shaping and no straight planes or surfaces.
I have included a basic picture in JPEG format for your review. This is the item from which I am trying in ACAD 2010 to construct into a usable adjustable form so I may parametric for my needs.
We received a surface model from a vendor that I have patched up as best I can, it still has one hole that I can find that I haven't been able to fill. Ideally we would like to have a solid model, but I'm running out of time to get this done and the surface model we have would be good enough for our purposes IF I can get the yellow surface tangent lines to turn off or change their color to black.
I've attached a jpg of the surface model with the yellow lines and uploaded the model here: [URL].....
How can I remove the lines in the middle after I press and pull the objects.
Attached is the Untitle.jpg, to make more clearer to you. Blue is the wall and skyblue is the aquarium. I want the back and the front of the aquarium don't have any line in the middle but even I do shade command the fill of the color is still there. Cause if I explode and delete the line in the middle the colors that fill the aquarium are getting rid off See Untitled 2.Jpg to see what I mean. And also how can make the aquarium Untitle 3.jpg transparent?