I cannot figure out how to create a solid surface on top of the retaining walls and also how to grade the transitions for the high to low points of the retaining wall. This would be so much easier for me in Solid Works
Untitled.jpg
I need to do a cut/fill analysis not residential site and this site has like 6 retaining walls there is a 6 foot difference in grade.
My surface is not recognizing the grade change when I make the polyline into a wall breakline.
I am having a lot of trouble adding retaining walls to my surface. I also have to add the curbs of parking lot.
I already have the surface. However I need to tell Civil3D to stop the contours at the retaing walls and not to try to tie them in to anything else. The closest I got was using wall breaklines and I got the top of the retaining wall to have the desired elevation. However, all the contours going to the retainig wall try to go around it and tie in to something else. This ends up creating weird contours and crazy slopes.
Now for curbs, how do I tell Civil3D to jump 6" when it reaches the curb line?
I've been trying to lay a mesh on top of some contour lines. I've also tried the loft command, but with little success.
I've tried several terrain plugins, but they all seem to malfunction because I have overlapping contours. Here is the dwg, what I'm trying to make.
A lot of my work is on steep slopes, and I need to incorporate sloping driveways, parking areas, site retaining walls (boulder walls as well as inter-locking block walls), benches between the top of one wall and the bottom of the next, re-grading, and landscape plans into the design model.
It seems Revit lacks any real site tools to accomplish these tasks, and there are some work-arounds. I've been playing w/ floors for a sloping driveway, but it's tedious and the results are mediocre at best. Haven't yet played with ramps for driveways. I haven't yet figured out a good way to deal with site retaining walls, where the bottom is sloped to match the driveway, and the top is at a different slope to match the existing/re-graded terrain above.
Any work-arounds to address issues with modeling driveways & retaining walls on a steep site?
As you can see, the nature of my model forbids me from making a 3D solid using LOFT.
The top surface is consisted of 3D polyline and arc, which if "joined" will be become a spline.
The bottom surface can easily be joined into polyline.
If I loft the top and bottom, it'll only give me a LOFTED Surface, which is not I want (wanted a 3D solid).
Is there a way to create hatching for the slopes surface style instead of using solid colors?
View 2 Replies View RelatedI am in Civil3D 2012, and am trying to render a retaining wall we doing. I set up a corridor, surface, and profile, and have it working with plans and such, but when I try my hand at rendering it looks rather odd. The surface is fine, and I can choose materials on the vertical wall subassembly, but It just shows a paper thin object ever 25' and a large surface on top. Does the top of the wall need a feature line as well.
View 1 Replies View RelatedI have finally created the shell of the complex surface that you see. This is only a section of the part because I cannot show the whole thing for proprietary reasons. I formed solid surfaces using the network command. The propblem is that it will not convert to a solid because the surface seams are not "water tight." When the network command created the solid surfaces, the surface seams do not exactly match the lines so there are gaps in all the seams. I have tried blending, patching, etc. and nothing works. how to convert this to a solid without losing the outlines and the shape?
View 3 Replies View RelatedI would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
View 9 Replies View RelatedI just tried to do a solid hatch I was filling some walls in plan. No matter how hard I tried it wouldn't let me do it. I didn't get any message asking if I had closed boundry etc. I have tried again a few times and no good. I rebooted computer, just in case, but still no good. I was doing solid hatching just the other day and am doing nothing different.
View 1 Replies View Relatedwe are in a situation where we want a dynamic wall label. how can i make that happen if technically the top of wall and bottom of wall are at two different x and y points. ideally i would like have one label and list it this way by referencing surface elevations:
RETAINING WALL
TOW=XXXX.XX
BOW=XXXX.XX
N=NORTHING
E=EASTING
I've always layout my floor plans three dimensional with the tools pallets commands such as walls, rails, door, windows & ect. I always have my walls pre-hatched with the solid pattern which is really effective to the floor plan. Normally when I put windows in the wall the window is clearly shown without the hatch in the wall but for some reason my wall's hatch started covering the windows and I can't seem to solve this problem.
View 0 Replies View RelatedWe received a surface model from a vendor that I have patched up as best I can, it still has one hole that I can find that I haven't been able to fill. Ideally we would like to have a solid model, but I'm running out of time to get this done and the surface model we have would be good enough for our purposes IF I can get the yellow surface tangent lines to turn off or change their color to black.
I've attached a jpg of the surface model with the yellow lines and uploaded the model here: [URL].....
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
Is there a easy way to make this into a solid.
View 5 Replies View RelatedI have created a model, by lofting a shape along a curved spline path. The model properties is currently '3d Solid' what I want to do is generate a 3d Face off of this model.
I have exploded the 3d model and that gives me a surface, bu the dilemma is that I do not know how to 'trace' or turn this surface into a 3d face format. What I was thinking is that if the surface could be exploded into individual elements I would be able to draw over the surface with the 3d face tools and then have my model, but a issue with this is that I cant explode the surface into elementary elements AND the 3dface tool cant generate curves.
In short how to turn a 3D model into a 3D Face or a Surface into a 3d Face?
The program I am exporting the model into accepts the following:
DXF Entity SAP2000 Objects
1 POINT Point
2 LINE Frame/NLink
3 3DFACE Area
4 3DPOLYLINE Solid
5 CIRCLE Line(s)
6 ARC Line(s)
Note: To be able to import the dxf entities as solids in SAP2000, you must draw them in AutoCAD as meshed polygons or meshed solids. I could also export the model as a solid but again do not know how to get a meshed polygon or meshed solid from my 3d solid, when I do mesh smooth, the model basically turns into a rectangle and looses its detail.
As you can see it is number 3 I am working on. I have managed to create simple 3d faces and get them into the program but the 3dface tool is very primitive and I cant see how I would create the curves that my model has, I cant seem to form a grid system either to use the 3dface - everything seems to draw in space.
Can I hatch a 3D solid surface? Do I have to create a 3D face on top of it beforehand?
View 7 Replies View RelatedI have asked to amend a drawing, which consists of lots of square tube sections and other stuff, however I have received it in IGS format. I have got it to open in AutoCAD by first opening it in Inventor, then using the 'Save Copy As' command to save it as a DWG. However, instead of it consisting of solid tubes which I assumed it would be for me to easily amend, it's all surfaces.
I can't find a way of opening it as a solid model (maybe the file type doesn't allow it anyway), nor can I seem to convert any of the surfaces into a solid.
I have attached a sample tube from the drawing, how to turn it into a solid? I am moderately experienced at solid modelling from scratch, but I've never come across something like this before.
BoxSection.dwg
Is it possible to convert surface into solid in AutoCAD 2002?
For example, can I convert these five surfaces into a solid pyramid?
If yes, what is the step to do it?
Is there a way to create a library of walls using dynamic blocks (similar to the walls in the full version of autocadd)? I've payed around a bit trying to create a dynamic block and I'm not having much luck.
View 9 Replies View RelatedI'm having a problem creating a 3D Solid from two 3dpoly lines. I'm attaching a script file which reproduces the two 3dpoly lines to use for the LOFT command. As you can see when running it, I have two closed 3dpoly lines which use exactly the same X,Y coordinates and differ only in the Z axis. I'd like to make a 3D Solid with these lines, which should be possible using the LOFT command... but I only get a surface around the 'sides'.
I needed to remove the .scr extension from the file in order to attach it, so to run it you need to replace .txt with .scr at the end of the filename. It's a standard ASCII script file. If someone prefers I can also give the coordinates of the 3dpoly lines as a post.
Is there any way to convert a surface to solid?
View 4 Replies View Relatedi have recived an igs fle which i imported into auticad 2012.when imported the and saved as an .dwg the model is in surfaces, im looking to convert the surface to solid so i can export the file as an .stl for 3d printing. is it possible to convert this?
View 7 Replies View RelatedI'm using ACAD 2014 Win8 64bit.
I need to slice a cylinder with a surface but the slice command keeps giving error " Inconsistent face-body relationships".
I created the surface from a solid that I created using solid intercept between the cylinder and another solid that the cylinder actually passes through (a housing I have). In my attachment I do not include the housing, just the cylinder, the solid intercept and the surface from the a face of the solid intercept.
I tried increasing the U & V isolines of the surface, and scaling it up so that it isn't bounded by the cylinder, but that didn't work.
I'm willing to try any technique that achieves the same goal - I need the butt of the cylinder to contour to the housing so that I can do a JOIN and have a solid housing with a cylinder sticking out of its face. The inside of the housing is hollow with a 0.05 inch wall.
PDS 2014/Win8 64/32GB RAM/256GB SSD RAID1/Asus P9X79 Deluxe/i7 3820/nVidia Quadro K2000D/Dual 27" LCD
I have a scanned model of a casting. It was necessary to delete surfaces to remove the casting flash from the model.
I have lofted/patched/stitched the missing surfaces to close the solid. Apparently there is a gap somewhere because the model remains as a surface instead of returning to a solid.
How can missing surfaces be found in the model?
What else can prevent the model from returning to a solid?
When stitching, the gap tolerance was set to .002". The model will "rebuild" without any error messages.
I am working on a project and have ran into a problem. I need to hollow out a currently solid surface in order for it to have a uniform thickness of 3mm that follows the curvature of opposite side. These pictures will show what I mean.
Top Side:
Bottom Side:
Basically, I need to hollow out the backside to make it fit the surface of the front side with a thickness of 3mm. Is there some sort of tool that is designed for this or another way of doing it?
I have created a surface in Civil 3D by adding contours....... Now that I have created the surface I need to Exoprt it to .sat / .stl files. But in order to do this I need a 3D Solid.
How do I convert this service to a 3D solid in order to the the export?
I have tried the thickening option in the 3D Modeling workspace but it doesn't want to accept my surface.
I have a model of a boat from some database. It's build from 3D faces but I would like to make it a 3D solid with a thickness of 3mm.
I can convert the faces into a surface, but i can't seem to get any of the two models into a 3D solid. I have tried thicken, convtosolid and a lot of other options without luck.
I was wondering if I could make two surfaces, one smaller than the other, place them ontop of eachother and create solid between them?
I'm having trouble trying to place a material onto a surface so that it aligns with the x-y coordinates. When I use drag and drop from the materials library and use ctrl to select one particular surface/face, the material drop s in fairly arbitrary.
I thought I could use materialmap to force it into a particular alignment and while I can use the commands to set the base point and alignment, the material does not update with the boxed alignment.
I have a solid that was created by extruding a regioned profile. I have made a lofted item (Yellow), that I will have to subtract from the solid (Green) to create a hole. When using the subtract command, I recieve the following error.
"The selected surface was ignored. Surfaces cannot be subtracted from solids or regions. At least two solids, surfaces, or coplanar regions must be selected."
I have tried convtosolid as well & to no avail.