I have a scanned model of a casting. It was necessary to delete surfaces to remove the casting flash from the model.
I have lofted/patched/stitched the missing surfaces to close the solid. Apparently there is a gap somewhere because the model remains as a surface instead of returning to a solid.
How can missing surfaces be found in the model?
What else can prevent the model from returning to a solid?
When stitching, the gap tolerance was set to .002". The model will "rebuild" without any error messages.
We received a surface model from a vendor that I have patched up as best I can, it still has one hole that I can find that I haven't been able to fill. Ideally we would like to have a solid model, but I'm running out of time to get this done and the surface model we have would be good enough for our purposes IF I can get the yellow surface tangent lines to turn off or change their color to black.
I've attached a jpg of the surface model with the yellow lines and uploaded the model here: [URL].....
I am working on a project and have ran into a problem. I need to hollow out a currently solid surface in order for it to have a uniform thickness of 3mm that follows the curvature of opposite side. These pictures will show what I mean.
Top Side:
Bottom Side:
Basically, I need to hollow out the backside to make it fit the surface of the front side with a thickness of 3mm. Is there some sort of tool that is designed for this or another way of doing it?
I was given a STEP file that was created in Solidwoks which when opened in Inventor 12' is a surface.
The surface can be successfully thickened after it is stitched, prior to stitching it fails due to it's complex obround, tapered, bell shape. However, because thicken only thickens perpendicular to the surface I end up with a lot of unusable ends with crazy angles and in many cases additional phantom surfaces which I cannot cut off or sketch on because they don’t really exist. Thickening has not been a serviceable option to this point.
All other techniques I try when making this model from scratch fail or do not match the original surface. Measuring the surface is difficult because the only measurements we get are the lengths of the loops, no radial measurements. Additionally, when I enter the solid I created from scratch into an assembly (whether it’s geometrically correct or not), I cannot constrain it, I can’t click on anything but the working planes – no surface, face or edge can be picked on the solid itself.
Making surfaces into workable solids? Is there anything I should do different? Is the sequence I am using incorrect? Correct order of operations they use to successfully create a solid from a surface?
Any program to convert 3D solids to a mid plane surfaces? We need our models in this form to do FEA work on them. I wanted to ask this question before I took on the task of trying to create one myself.
I am trying to convert this composite surface into a single solid body, however when I try to stich the surfaces in the construction environment it always crashes. I have also tried edditing the STEP file import options but it still always opens as a composite surface.
I use INV 2013. MOVE THE END OF THE PART DOWN TO SEE WHATS HAPPENING. (MOVED TO REDUCE THE FILE SIZE). I am trying to split the solid using the surface as shown.
But, I am unable to do so. Also, I need to create a new surface with 0.50mm offset to create female form die.How to do it.
I have a multibody surface part, which is derived from a multibody part. Therefor there are multiple contiguous surface parts that are isolated from each other.
Is there a way to STITCH or convert one of these contiguous surfaces into a solid part ?
Note: I tried the THICKEN tool but the hole features do not come out right. Some holes are missing or the hole depths are wrong.
I have finally created the shell of the complex surface that you see. This is only a section of the part because I cannot show the whole thing for proprietary reasons. I formed solid surfaces using the network command. The propblem is that it will not convert to a solid because the surface seams are not "water tight." When the network command created the solid surfaces, the surface seams do not exactly match the lines so there are gaps in all the seams. I have tried blending, patching, etc. and nothing works. how to convert this to a solid without losing the outlines and the shape?
I am trying to find a way to import a laser scanned mesh or point cloud file into Inventor (2013) such that I can use it to make a parametric representation of the form. The import format can be STL, OBJ, VRML, XYZ or PLY. I have tried the Mesh Enabler from Autodesk Labs but the files I am looking to work-on are bigger than the enabler can cope with and my system slows right down or locks-up.
I know bespoke reverse engineering software is the ideal way to go but I was hoping there was a way to model over a mesh to represent its form to create a placeholder in a parametric assembly. I'm not looking for accuracy, just a surface or solid output that can be constrained to native inventor parts. If I could get the files to STEP or IGES someway that would be enough.
I would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
My problem today is that I made a Model of a Part of a ship using surfaces rather than solids because the engineer thought it would be easier to bring into ANSYS program for analysis but he is now having a problem with it and I am looking into converting my current model to solid. I can do it but the method I thought of using is quite long winded and we are working to a tight deadline.
1.open up the surface part
2.use "Offset/Thicken"
3.any clashes between parts make a sketch and cut away.
the problem is the amount of plates I have and the time it takes to sort them out.
I have created a model, by lofting a shape along a curved spline path. The model properties is currently '3d Solid' what I want to do is generate a 3d Face off of this model.
I have exploded the 3d model and that gives me a surface, bu the dilemma is that I do not know how to 'trace' or turn this surface into a 3d face format. What I was thinking is that if the surface could be exploded into individual elements I would be able to draw over the surface with the 3d face tools and then have my model, but a issue with this is that I cant explode the surface into elementary elements AND the 3dface tool cant generate curves.
In short how to turn a 3D model into a 3D Face or a Surface into a 3d Face?
The program I am exporting the model into accepts the following:
DXF Entity SAP2000 Objects 1 POINT Point 2 LINE Frame/NLink 3 3DFACE Area 4 3DPOLYLINE Solid 5 CIRCLE Line(s) 6 ARC Line(s)
Note: To be able to import the dxf entities as solids in SAP2000, you must draw them in AutoCAD as meshed polygons or meshed solids. I could also export the model as a solid but again do not know how to get a meshed polygon or meshed solid from my 3d solid, when I do mesh smooth, the model basically turns into a rectangle and looses its detail.
As you can see it is number 3 I am working on. I have managed to create simple 3d faces and get them into the program but the 3dface tool is very primitive and I cant see how I would create the curves that my model has, I cant seem to form a grid system either to use the 3dface - everything seems to draw in space.
I have asked to amend a drawing, which consists of lots of square tube sections and other stuff, however I have received it in IGS format. I have got it to open in AutoCAD by first opening it in Inventor, then using the 'Save Copy As' command to save it as a DWG. However, instead of it consisting of solid tubes which I assumed it would be for me to easily amend, it's all surfaces.
I can't find a way of opening it as a solid model (maybe the file type doesn't allow it anyway), nor can I seem to convert any of the surfaces into a solid.
I have attached a sample tube from the drawing, how to turn it into a solid? I am moderately experienced at solid modelling from scratch, but I've never come across something like this before.
I'm having a problem creating a 3D Solid from two 3dpoly lines. I'm attaching a script file which reproduces the two 3dpoly lines to use for the LOFT command. As you can see when running it, I have two closed 3dpoly lines which use exactly the same X,Y coordinates and differ only in the Z axis. I'd like to make a 3D Solid with these lines, which should be possible using the LOFT command... but I only get a surface around the 'sides'.
I needed to remove the .scr extension from the file in order to attach it, so to run it you need to replace .txt with .scr at the end of the filename. It's a standard ASCII script file. If someone prefers I can also give the coordinates of the 3dpoly lines as a post.
i have recived an igs fle which i imported into auticad 2012.when imported the and saved as an .dwg the model is in surfaces, im looking to convert the surface to solid so i can export the file as an .stl for 3d printing. is it possible to convert this?
I need to slice a cylinder with a surface but the slice command keeps giving error " Inconsistent face-body relationships".
I created the surface from a solid that I created using solid intercept between the cylinder and another solid that the cylinder actually passes through (a housing I have). In my attachment I do not include the housing, just the cylinder, the solid intercept and the surface from the a face of the solid intercept.
I tried increasing the U & V isolines of the surface, and scaling it up so that it isn't bounded by the cylinder, but that didn't work.
I'm willing to try any technique that achieves the same goal - I need the butt of the cylinder to contour to the housing so that I can do a JOIN and have a solid housing with a cylinder sticking out of its face. The inside of the housing is hollow with a 0.05 inch wall.
I have created a surface in Civil 3D by adding contours....... Now that I have created the surface I need to Exoprt it to .sat / .stl files. But in order to do this I need a 3D Solid.
How do I convert this service to a 3D solid in order to the the export?
I have tried the thickening option in the 3D Modeling workspace but it doesn't want to accept my surface.
I have a model of a boat from some database. It's build from 3D faces but I would like to make it a 3D solid with a thickness of 3mm.
I can convert the faces into a surface, but i can't seem to get any of the two models into a 3D solid. I have tried thicken, convtosolid and a lot of other options without luck.
I was wondering if I could make two surfaces, one smaller than the other, place them ontop of eachother and create solid between them?
I'm having trouble trying to place a material onto a surface so that it aligns with the x-y coordinates. When I use drag and drop from the materials library and use ctrl to select one particular surface/face, the material drop s in fairly arbitrary.
I thought I could use materialmap to force it into a particular alignment and while I can use the commands to set the base point and alignment, the material does not update with the boxed alignment.
I have a solid that was created by extruding a regioned profile. I have made a lofted item (Yellow), that I will have to subtract from the solid (Green) to create a hole. When using the subtract command, I recieve the following error.
"The selected surface was ignored. Surfaces cannot be subtracted from solids or regions. At least two solids, surfaces, or coplanar regions must be selected."
I'm trying to split a single solid body into 2 solid bodies. The problem is that the body I'm trying to split consists of two separate pieces. I can split a body when it is a single piece no problem, but I'm having the problem when the two pieces are not joined at all.
When I try and split it on the origin plane it gives this error:
"Creating parting line failed. Could not build this Split"
When I try and split it on a work plane lying on one of the pieces it gives this error:
"Creating parting line failed. Modeling failure in ASM. Redefine inputs."
Or, another variation on this erorr:
"Creating parting line failed. Split feature could not create two bodies. Change the Split Tool so that split feature can create two bodies."
I cannot figure out how to create a solid surface on top of the retaining walls and also how to grade the transitions for the high to low points of the retaining wall. This would be so much easier for me in Solid Works
My ultimate aim for this small drawing is to convert it to an .STL file. For this the shape needs to be a solid or watertight mesh. I've attached the drawing in CAD - it's very basic! I just want to create a solid shape, using the surface, with a flat base up to the lines drawn on. Or even just a surrounding mesh so that the shape can be exported as a .STL. I just can't figure out how to do it!
