Revit :: How To Create A Sloped Wall By Creating A Mass In Place
Apr 18, 2013
I am trying to create a sloped wall by creating a mass in-place. First I draw a line on a surface at a pre-determined level that I've set up in elevation. Then I offset this line in the vertical plane. My next step is to offset this second line so that it is not directly above the original line, but offset in the horizontal plane. How do I change from a vertical to a horizontal offset? I’ve tried different work planes, but they all offset vertically.
View 6 Replies
ADVERTISEMENT
Apr 5, 2012
I'm following a "Simple Mass Creation" exercise in a Revit book, which says to create a cube, a sphere, and a pyramid. It doesn't say how, though, it just goes on to the next step of dividing the masses into floors. After much research and trial and error, I figured out the cube and sphere, but how the heck do you create a pyramid? At first I was thinking of a blend, from a square to a point, but that's not an option. Then I tried to use void shapes to remove parts of a cube...and I'm getting an error message because my voids are overlapping and there's no solid to cut. There MUST be a faster and less complicated way to create such a basic form.
View 5 Replies
View Related
Feb 21, 2014
I have a colleague who has counciled me that sometimes it makes sense to create mass-elements for complicated gabled roof elements. Since I am pretty darn new to Revit, I am bringing in some old 2D dwg information (plans and elevations) and I'm trying to use this information to generate an in-place mass that is my roof. I'm essentially extruding gabled roof information from this geometry. So far so good. But when I try to rotate this information I find the program unwilling to do this. I have a suspicion this has something to do with the fact this in-place mass is either being hosted by the intitial horiontal working plane, or it is "pinned" to something I don't want it to be pinned to.
View 9 Replies
View Related
Dec 29, 2011
I would like to know whether it is possible (and how) to trim a wall that was generated from mass face to a roof (also generated from face mass) or/and make a horizontal hole in it. The wall itself is not straight or curved, it shifts outwards from the building from base to top (still in an elevation it looks like rectangle).
View 2 Replies
View Related
Jun 7, 2012
Is there any method to create sweep or shaped object in mass (should be in dimension) using Revit 2012.
The creation of sweep/revolve/blend is not available in Mass of Revit 2012.
Because the method of mass is difference comparing to Revit 2008 with Revit 2012.
View 2 Replies
View Related
Oct 3, 2011
In Revit 2012, how do I place a wall at an angle to the ground plane, so it can be connected to a roof above? I have tried placing a wall on level and rotating it, however it does not appear to work. I can rotate other elements, but not walls.
View 1 Replies
View Related
Feb 25, 2014
Is it possible to add a standard wall opening in a wall that i have modelled in place?
I know i can add a void extrusion to the model just wondering if there's a setting i can change to allow me to use the standard wall opening comand.
View 1 Replies
View Related
Jan 16, 2013
I am creating a tunnel with a profile consisting of multiple radios. In the attached images can be displayed. The problem I have is that by selecting one of the two tunnels and create a void with the profile of the second tunnel and perform cutting geometry indicates that I can not and I get the error message.
If I perform the same exercise to select a tunnel and create a void with a square profile, rectangular or cylindrical deaja if I make the cut geometry. I select the void that did work and edit it to add the profile you require and at the end of the model throws me the error again.
We are working on four computers of the same features and the same version of Revit Building Design Suite 2013, has installed the update 2.
View 1 Replies
View Related
Nov 16, 2011
I am trying to create a mass surface that is being cut by a topo plane. What I am trying to achieve or show is a height setback set from the existing topo to a height of 35'. I've tried to cutting or joining the two geometries but this will not work. There is no way to snap t the intersection of were the mass and the Topo surface meet. Is there a way to change a Topo surface into a mass? Any other way to achive this instead of massing and topo surfaces?
View 5 Replies
View Related
Feb 21, 2012
How do I create simple wall types? I would like to create 2x6 and 2x4 walls with 7/16" OSB on them. I would like to see each stud when I going into 3D and I would like the dimensions to be from face of framing; not the OSB or centerline.
I would like to mimic the plan dimensions when I input the building into Rivet. Basically, I want to build a stick framed home so I can add the floors, walls and roof and then go into the mechanical and see how it all stacks out and is going to come together.
View 7 Replies
View Related
Oct 30, 2012
I want to Create a Wall Nitch that will be in a tiled shower we are doing. Best way to create a family that cuts into a wall? I don't want to Create an opening, because I don't want it going all the way through the wall.
View 4 Replies
View Related
Feb 13, 2006
I have tried 2 methods of generating a parapet cap:
1 - Creating a wall style with the sweep.
2 - Added a host sweep.
The problem is that using either method or a combination of both methods doesn't always work. I still end up with some caps that don't miter correctly even after editing. Sometimes, different intersections will miter and others won't.
View 9 Replies
View Related
Aug 12, 2008
I would like to create a family component using the wall foundation bearing footing as a template. I cannot find the file where the templates are located. I tried using the structural footing template but it would not give me the same flexibility the wall foundation bearing footing template does.
View 2 Replies
View Related
Jul 22, 2013
I'm trying to create a Tiled Skirt (150x150mm) profile or pattern to be used as Wall Sweep. Is there anyway to create this profile as the Family Template: metric profile (wall hosted) only allow me to create a 2D profile.
I would prefer to avoid detail lines or Filled region to get the tiles shown as I need to schedule and quantify this element.
View 1 Replies
View Related
Aug 9, 2013
When I create the surface in conceptual mass and bring that in revit project and apply wall by face I see interior face of wall going exterior.
Can this be set in conceptual massing while creating surface so that when I apply wall by face interior face remains interior.
View 7 Replies
View Related
Jun 20, 2012
Most of the interior walls in the house are the same materials and finishes - finishes of veneer plaster painted, but rooms are to be differnent colors. I can make a wall the color that I want, but ALL that type walls become that color. Is there any way to make several different colors of rooms witihout creating literally dozens of different wall types?
View 4 Replies
View Related
Oct 1, 2012
How to place the “midpoint” of window on the midpoint of wall?
In the screenshot below, I wanted to place the window from its midpoint to the midpoint of the wall. How this can be performed on Revit?
View 2 Replies
View Related
Mar 26, 2013
I am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.
View 1 Replies
View Related
Oct 20, 2010
Is it possible to create the Wall family in revit?
View 5 Replies
View Related
Nov 29, 2011
I am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies
View Related
May 22, 2012
how to create a wall schedule with areas. To find out how much plasterboard, paint etc. I need for a building.
View 1 Replies
View Related
Sep 9, 2011
How to create curtain wall with Mullion and insert in to project.
View 1 Replies
View Related
Sep 1, 2011
I am trying to create a cornice using a wall sweep. I created the profile I need but when I load the profile and try to add the sweep to the wall Revit shuts down completely.
View 1 Replies
View Related
Nov 22, 2012
I need to create a wall the has a profile (in plan view).
View 1 Replies
View Related
Apr 30, 2013
Is it possible to create a wall in Revit that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 2 Replies
View Related
Dec 31, 2012
I read a 2009/10 thread, "Rotating lighting", describing how to work around the problem of family lighting fixture members not rotating. I would hope there is a better solution today.
I simply want to place a lighting fixture - std 2x4 flourescent, on a 7 deg sloped ceiling. The axis of rotation is the long run of the light fixture. Is this not possible in Revit 2013?
Or, do I have to dredge up the work around from 3 releases ago and attempt to discern how to make it work?
It seems like I should just be able to set the family to use a work plane-based assignment and then place it with the correct work plane active. That is not happening. The light fixture doesn't want to rotate the 7 degrees to align with the work plane.
View 9 Replies
View Related
Jan 27, 2012
I am trying to create a custom curtain wall which will contain vertical strapping for the vertical mullions and horizontal wood boards. I created the two profiles and am able to create the curtain wall type control spacing etc...This looks great in elevation and plan, but when I cut a section detail the vertical strapping is cut at every horizontal mullion.
My question in short! If I want to create the look of continuous horizontal boards how can I prevent the vertical mullions from being cut? I'd rather not offset them apart so I can use this model element in details. See the section detail view attached.
View 1 Replies
View Related
May 20, 2013
I am working on the project with sloping roof. I have drawn beams with slope. however when I am drawing slab with slopes I am not getting this slopes. There is gap between the beams and slab. I have attached screen shot for more information. Also I need to apply loads for this sloped roof.
View 4 Replies
View Related
Feb 2, 2013
Working on a project with a green house. I created a roof using "roof by footprint". I selected "sloped glazing" and assigned mullions for the various conditions as well as spacing.
The walls below are curtain walls. When I create the roof, the mullions are oriented the wrong way. How do I control the orientation of the mullions?
In desperation, I mirrored the roof about a vertical axis. See images below.
This corrected the orientation for me, but I must believe there is a better way! A "proper way"... Did I miss something in the initial creation of the roof? I changed the sloped glazing of the roof to a basic roof. When I do this I notice the roof moves up.
I assume this is when the orientation of my roof inverted...
View 1 Replies
View Related
Apr 15, 2013
See attached. What's the best way to model this sloped grade beam? Can I use the sweep?
View 4 Replies
View Related
Aug 20, 2013
I need to model a building that cascades down a steep sloped hill. Should I create a toposurface first and then model onto that or should I make my model and then apply it to a toposurface?
View 1 Replies
View Related
