Revit :: Light On Sloped Ceiling
Dec 31, 2012
I read a 2009/10 thread, "Rotating lighting", describing how to work around the problem of family lighting fixture members not rotating. I would hope there is a better solution today.
I simply want to place a lighting fixture - std 2x4 flourescent, on a 7 deg sloped ceiling. The axis of rotation is the long run of the light fixture. Is this not possible in Revit 2013?
Or, do I have to dredge up the work around from 3 releases ago and attempt to discern how to make it work?
It seems like I should just be able to set the family to use a work plane-based assignment and then place it with the correct work plane active. That is not happening. The light fixture doesn't want to rotate the 7 degrees to align with the work plane.
View 9 Replies
ADVERTISEMENT
May 20, 2010
I'm use to working with autocad layers.In AutoCAD if I'm drawing electrical plan and floor plan, HVAC...ect I just freeze in viewport the things I don't want to see for that particurler sheet.
In Revit I duplicated my floor plan to create my electrical plan. I can add my recepticals and switchs but it won't let me add light fixture. Do I add the light fixture to ceiling plan then some how move them to my electrical plan?
View 9 Replies
View Related
Jun 22, 2012
Any lighting fixture families in revit Architecture that snap to the ceiling grid? I've seen them in Revit MEP. Would be a lot nicer than having to align them manually.
View 1 Replies
View Related
Jul 24, 2012
Having trouble creating arrays of ceiling light fixtures in Revit 2013? It gives me this error message;
'Can't place inserts outside of hosts. These elements won't be copied'
I've adjusted all manner of settings to make sure the copies don't fall outside the limits of the host ceiling but without success. It only occurs with linear arrays on ceilings not radial arrays for ceilings or linear or radial arrays for walls?
View 9 Replies
View Related
May 20, 2013
I am working on the project with sloping roof. I have drawn beams with slope. however when I am drawing slab with slopes I am not getting this slopes. There is gap between the beams and slab. I have attached screen shot for more information. Also I need to apply loads for this sloped roof.
View 4 Replies
View Related
Feb 2, 2013
Working on a project with a green house. I created a roof using "roof by footprint". I selected "sloped glazing" and assigned mullions for the various conditions as well as spacing.
The walls below are curtain walls. When I create the roof, the mullions are oriented the wrong way. How do I control the orientation of the mullions?
In desperation, I mirrored the roof about a vertical axis. See images below.
This corrected the orientation for me, but I must believe there is a better way! A "proper way"... Did I miss something in the initial creation of the roof? I changed the sloped glazing of the roof to a basic roof. When I do this I notice the roof moves up.
I assume this is when the orientation of my roof inverted...
View 1 Replies
View Related
Apr 15, 2013
See attached. What's the best way to model this sloped grade beam? Can I use the sweep?
View 4 Replies
View Related
Aug 20, 2013
I need to model a building that cascades down a steep sloped hill. Should I create a toposurface first and then model onto that or should I make my model and then apply it to a toposurface?
View 1 Replies
View Related
May 16, 2012
I have a 6 pitch connecting to a 9 pitch roof. I go and make an eyebrow dormer along the 6" pitch roof and the dormer automatically is drawn as a 9 pitch with a crazy peak (almost church like). I cannot adjust the pitch of the eyebrow to make it look appealing.
View 3 Replies
View Related
Sep 17, 2012
I made a metal standing seam roof by putting mullions on sloped glazing roof. Is there a way to extend the mullions past the edge of the perimeter of the roof?
View 4 Replies
View Related
Mar 22, 2013
I have a situation of one sloped floor connecting two horizontal floors. They build together a continuous surface.
I need to join them and have the layers be continuous along the structure. If they were roofs, no problem, I could use the "roof by extrusion" command.
Should I do that? If I try to use floors.....
When I model them as three separate floors, and then Join them, it doesn't work. meaning that the layers within the floor don't match (well, they can't, in fact! I have to move the floor behind!)
If I model one single floor and then add split lines, and move them... it does work. BUT..... I have a stairs on top of it! the stairs have a different slope than the floor, and i need to build a variable layer that fills the void between the floor and the stairs.
So my hypothesis was: I put a sloped floor through the slope arrow... and then adjust one variable layer to do the inflill...
My dream would be to join then floor and stairs.... The material is the same
View 2 Replies
View Related
Mar 25, 2013
How to show sloped rafters in section and in plan correctly? The attached plan shows the rafters as a structural beam system and I do not know how to slope the beam system to match the roof pitch.
View 2 Replies
View Related
Apr 18, 2013
I am trying to create a sloped wall by creating a mass in-place. First I draw a line on a surface at a pre-determined level that I've set up in elevation. Then I offset this line in the vertical plane. My next step is to offset this second line so that it is not directly above the original line, but offset in the horizontal plane. How do I change from a vertical to a horizontal offset? I’ve tried different work planes, but they all offset vertically.
View 6 Replies
View Related
Oct 20, 2011
Is there a way to avoid super Elevation or Side Friction in Sloped Surfaces for Curves, such as Building Pads, Ramps, Floors, etc.. Is it mandatory.. ?? Its a problem all the time worrying about matching levels in topo surface and floors for gradual slopes in site and side friction in sloped ramps or sloped building pads.. that matching line between levels doesn't look good while giving presentations..
I have also attached an image for reference.. both the sloped surfaces are building pads..
View 6 Replies
View Related
Dec 6, 2010
How do I use the standard Revit can lights in a wood joist floor with drywall applied to the bottom? If I place in a suspended ceiling, can lights light up just fine. However, if I use them in the floor space of a wood joist floor, the light itself gets covered with the floor. How can I get the light to cut the floor out so I can see the light when it is rendered?
View 4 Replies
View Related
Oct 25, 2011
Is there a setting to export the grid lines of ACT ceiling in a 3D view to DWG?
I don't know if there is because I can't even get the grid lines to show in a 3d view. Right now the view shows the ACT ceiling as a simple geometric shape.
View 9 Replies
View Related
Mar 27, 2013
With no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 3 Replies
View Related
May 22, 2012
Basic master bedroom with a view. roof has a 9 pitch. I cannot figure out how to put a cathedral ceiling in. How do you?
View 4 Replies
View Related
Dec 3, 2012
I am laying out a simple structure. Bearing wall to bearing wall is 35’, with a few non bearing walls between the bearing walls. I will be using a truss to span from bearing wall to bearing wall. What would be the best work flow for the drywall ceiling material. The ceiling seems to require a core element. I cannot seem to manage drywall alone. If I create a ceiling with 2x4 core and drywall finish and create a ceiling over the whole area the ceiling seems to auto dim to the ceiling finish and not the core 2x4. Then there is the issue of the clean up at the top plate were the wall and ceiling finishes meet
View 1 Replies
View Related
Jun 13, 2012
I have one of the floors in our building doing something wacky. The 5th floor reflected ceiling plan looks fine so I create detail plans for the suites at a different scale. this new suite blowup has what looks to be the same suite but everything is greyed out and when i switch from coarse detail to fine detail it doesn't do a thing.
The orignal full reflected ceiling plan looks fine. The line are black. The detail swithces back and forth... I can;t figure out what the problem could be. I used the same process on other floor and everyting is OK. The View Ranges are the same and everthing else in the properties seem the same too.
View 3 Replies
View Related
Aug 15, 2013
I have a problem. The linked model from our electrical engineer its lights are at the correct height but the ACT ceiling is still running its lines throiugh the lights. how do we take care of this to where the linked model which has the lights in it cut through our ACT ceiling from our central model?
View 2 Replies
View Related
Oct 9, 2013
I'm using Revit 2014 & have not been able to fade the ceiling grid lines so they don't plot out so heavy on my dwgs. I've tried overriding graphics of these grids with half tone which didn't work then I tried transparency & that did not work. They either stay on or turn right off!
View 4 Replies
View Related
Nov 3, 2009
Are there any plans to add the simple yet productive feature of moving an object in the X and Y directions at the same time?Also, I would love to be able to select the ceiling grid and hit the space bar and have the grid rotate 90 degrees.
View 4 Replies
View Related
Apr 26, 2012
How can I move my air vents to the ceiling plan from the floor plan ?
View 1 Replies
View Related
Jul 26, 2011
I have fixtures on the reflected ceiling plan showing up in the foundation. How to stop this
View 1 Replies
View Related
May 24, 2013
Is there a way to get the ceiling height automatic in a schedule?
View 4 Replies
View Related
Sep 9, 2013
How We can to change the default height Ceiling plane In Project Browser.
For example, the Default is 2600mm.
I want to Over 2800mm set.
Not in Time Drawing Ceiling.
View 2 Replies
View Related
Jul 8, 2013
I want to place a Skylight on a Slope Roof that will be channel vertically thru the Raked Ceiling System. I need to show this skylight on Roof and Ceiling plans. without tracing lines or using Vertical command.
View 3 Replies
View Related
May 15, 2012
I've got some troubles creating a proper ceiling plan. What goes wrong (imo) is that my wall sweep is shown on my ceiling plan while it shouldn't.First image shows the ceiling plan. (on image 3 you will see the wall sweep I mentioned in red).
This image shows the view range used.This images shows the section (right), 3d (top left) and ceiling plan (bottom left) highlighted the wall sweep.Why / how do I prevent this wall sweep from showing up?
View 9 Replies
View Related
Apr 2, 2013
I'm inquiring whether or not it is possible for Revit ceilings to be customized by the input of a user regarding the shapes and sizes without using a .pat file. Almost like a parametric object with predefined limitations. For example: a rectangular ceiling tile 'x' can be from 6 inches to 10 feet and side 'y' can be from 6 inches to 6 feet. So someone can select the ceiling type and actually input what size 'x' and 'y' they'd like while staying within those limitations.
View 1 Replies
View Related
Dec 1, 2013
I recently built a model-in-place generic model ceiling canopy using Revit 2013. I want to place lights (recessed cans) in the model. Can I change the model type to ceiling or is there a way to place light fixtures in it?
View 2 Replies
View Related
