Revit :: Error Creating A Void In A Mass
Jan 16, 2013
I am creating a tunnel with a profile consisting of multiple radios. In the attached images can be displayed. The problem I have is that by selecting one of the two tunnels and create a void with the profile of the second tunnel and perform cutting geometry indicates that I can not and I get the error message.
If I perform the same exercise to select a tunnel and create a void with a square profile, rectangular or cylindrical deaja if I make the cut geometry. I select the void that did work and edit it to add the profile you require and at the end of the model throws me the error again.
We are working on four computers of the same features and the same version of Revit Building Design Suite 2013, has installed the update 2.
View 1 Replies
ADVERTISEMENT
Jun 7, 2012
Is there any method to create sweep or shaped object in mass (should be in dimension) using Revit 2012.
The creation of sweep/revolve/blend is not available in Mass of Revit 2012.
Because the method of mass is difference comparing to Revit 2008 with Revit 2012.
View 2 Replies
View Related
Jan 6, 2014
I've drawn a cross section,When I select them,I choose to create forms,The following warning appears.
View 2 Replies
View Related
Apr 18, 2013
I am trying to create a sloped wall by creating a mass in-place. First I draw a line on a surface at a pre-determined level that I've set up in elevation. Then I offset this line in the vertical plane. My next step is to offset this second line so that it is not directly above the original line, but offset in the horizontal plane. How do I change from a vertical to a horizontal offset? I’ve tried different work planes, but they all offset vertically.
View 6 Replies
View Related
Aug 5, 2013
I have a complex part that will be created using additive manufacturing. Since this type of machining is adding material needed rather than removing material, I would like the make voids and hollow out the part wherever possible to reduce the manufacturing time, and the weight of the part. Are there any features in Inventor that allow you to click on an internal volume and specify a void that produces certain wall thickness? The closest feature I can think of is the Shell feature but that only works for parts with very simple geometry and it doesn't make a void like I would like. The shell feature cuts out material from the face so it is good for making something like a cup but does not make an internal void.
View 9 Replies
View Related
Feb 5, 2013
I am working a little 'off piste' currently as I am usually designing buildings, however, I have been asked to design a mould for the casting of an additional mass of lead to be appended to the existing lead in the keel of a yacht.
In order to complete this exercise the volume of the mould must accommodate between 26 and 30 litres of lead which is the volume of lead required to give the correct weight.
I have begun this task by creating a new Revit Family (may have been better to create it in a Project Environment) essentially being a large extrusion, with a number of swept blend voids creating the mould cut out. I have determined this using my clients instructions for the type of cross sectional profile, its profile along its length and the footprint. Thing is I now have to work out what alterations are necessary in order to ensure that the mould volume is correct! See 3D View so far.
View 7 Replies
View Related
Jul 25, 2011
I am trying to create a void form in revit architecture, i am following the quick start tutorial from the design academy website and when I try to make a void form i get an error, pics to explain:
View 1 Replies
View Related
Feb 7, 2013
Can a void be converted to a solid?
View 6 Replies
View Related
Oct 26, 2013
I am trying to make a void element but whatever I do this message occurs: "Some Void Forms of this family do not cut anything and will be deleted. To make a Void Form cut something else use the Cut Geometry tool." I am using "Model in place" tool -> Generic models.
I use Revit 2014 with Service Pack 1.
View 1 Replies
View Related
Oct 6, 2013
When adding an element, say a door, to something like a wall, if there is a void within the door and everything is set properly to cut out a section of the wall, what is the resultant material colour that you see at the cut?
I've been trying this out and in the Realistic display mode, when I have a door with a recess profile around the frame, in brick I see the brick colour, but in plaster I see a grey which isn't the same as the default plaster colour?
The recess is 12mm into 12.5mm plaster.
View 1 Replies
View Related
May 29, 2012
What would be possible reason for a void not having any effect on cutting an object? I created a parametric void.Then I created an object.No change to the object. If I create an object then a void, it seems to work.
View 1 Replies
View Related
Nov 7, 2012
I am having problems with void that i cant hide in my project. The void is inside my generic family but wont apply a cut unless i apply a length parameter to it. The problem i that in my project it seems to be visible as a yellow box that will also appear when printed.
Is it possible to hide this in the project by any way?
View 1 Replies
View Related
Oct 27, 2011
I have inserted a recess paper towel dispenser into an interior wall. Then a 1/8" tile wall was added in front of the hosting interior wall. The opening for the recess dispenser only cut into the interior hosting wall, not the tile wall. I tried joining the two walls, but it didn't seems to have any effect. Is there any reason why the walls won't join?
View 4 Replies
View Related
Nov 27, 2013
I have created a simple pipe fitting family, a soil vent pipe terminal infact, but I cannot get the solid body created from a rotated profile to be cut by an arrayed extrusion void. I keep getting the error message, 'Can't keep the elements joined'!
View 2 Replies
View Related
Jun 6, 2012
I need to resolve the corner condition where two boards intersect. I am not able to create a void in order to cut the corner for the geometry. I would like to shape more than one side of the board and make it rounded. How do I edit the different sides of the geometry?
See attachment for Revit model:
View 9 Replies
View Related
Jun 30, 2012
I created a reception desk in Revit 2013 using solid extrusions and void extrusions and it looks really good. The problem is I need to recreate this thing using some other method since I cannot place door and drawer faces on a plane that technically, geometrically does not exist, ie the area a receptionist would sit. The rendering of my extruded desk is attached.
View 8 Replies
View Related
Nov 6, 2013
We just noticed that the imported cad geometry in a Mass family will not cut in a floor plan view which contains a plan region. Regardless of the location or height of the plan region.
View 4 Replies
View Related
May 25, 2013
When I import a AutoCad 2D file (include several layers) into Revit, how can I extrude layer by layer (for having mass )? I mean I need to have a chance for selecting my layers separately in Revit (like in AutoCad) and then create Mass by layers.
View 2 Replies
View Related
Feb 14, 2013
I have a relatively simple mass modeled in Rhino that I imported to a Revit Mass Family (via .sat file). I then placed walls, roofs, structure on the face of this mass. However I would like to be able adjust this mass, either in Rhino or Revit and the walls and structure adjust accordingly. Now however, if I reload the mass into my Revit family, and then reload the family to my model, and then attempt to Update to Face, the error "Faces defining this Element cannot be reacquired." and my only option is to delete the offending wall/roof etc.
Is this just a limitation in Revit/Rhino, or am I totally doing it wrong?
View 9 Replies
View Related
Apr 5, 2012
I'm following a "Simple Mass Creation" exercise in a Revit book, which says to create a cube, a sphere, and a pyramid. It doesn't say how, though, it just goes on to the next step of dividing the masses into floors. After much research and trial and error, I figured out the cube and sphere, but how the heck do you create a pyramid? At first I was thinking of a blend, from a square to a point, but that's not an option. Then I tried to use void shapes to remove parts of a cube...and I'm getting an error message because my voids are overlapping and there's no solid to cut. There MUST be a faster and less complicated way to create such a basic form.
View 5 Replies
View Related
Feb 21, 2014
I have a colleague who has counciled me that sometimes it makes sense to create mass-elements for complicated gabled roof elements. Since I am pretty darn new to Revit, I am bringing in some old 2D dwg information (plans and elevations) and I'm trying to use this information to generate an in-place mass that is my roof. I'm essentially extruding gabled roof information from this geometry. So far so good. But when I try to rotate this information I find the program unwilling to do this. I have a suspicion this has something to do with the fact this in-place mass is either being hosted by the intitial horiontal working plane, or it is "pinned" to something I don't want it to be pinned to.
View 9 Replies
View Related
Aug 22, 2011
Is there any way to change the appearance of a mass imported into Revit? I simply want to change the dark grey that shows in the rendered view and/or the white that shows up in the shaded view so I can control how background buildings (imported through google earth/sketch up) look in my drawings.
I do not want to rebuild the masses with walls, ceilings, etc, because they are just background site elements. I have tried to do this through object styles. I have tried to do this through "Override by Element" and "Override by Category". I am importing the files as in-place masses and there is no way to edit materials because "Materials" doesn't even show up as one of the element properties.
View 9 Replies
View Related
Jan 23, 2012
I have problem when i try to use function analyze mass model in revit building they show message like attached file.
View 1 Replies
View Related
Jan 6, 2014
I MAss space across a strange problem.
I chose a number of elements drawn ,And then I needed them again in the future I choose, Thus after selecting elements Click on the Save
Selection And I value Enter for selected elements.
Now that I'm on Manege Selection panel is not,Is not Load Selection Options.
In none of the family environment.....
When we choose an element appears,But the project environment There are icons at the Manege.
Project Tab:
Mass and Family :
View 4 Replies
View Related
Mar 2, 2011
I assigned to each mass floor an usage, and my schedule functions well . That tool is wonderful, isn't it?
But I would want to display each usage in a different color, to show my client how I am organizing the building. Is this possible? Mass floors seems not to have a color or material property.
View 2 Replies
View Related
Jul 21, 2011
I think there might be a bug in Inventor 2012 with regards to derived components and their physical properties, otherwise I've never noticed it before...
If I derive a component and use an IAM as the Base Component and choose the 'Single composite feature' as the option then the physical properties of the newly created derived IPT is the same as the original IAM. That is expected behaviour when you choose one of the Solid options, but a Surface shouldn't have a mass - by definition.
If I use an IPT as the Base Component, I get the expected behaviour, i.e., a surface doesn't have a mass.
The whole purpose of creating a 'Single composite feature' as a surface is unnecessary if it's going to have physical properties...
View 3 Replies
View Related
Nov 16, 2011
I am trying to create a mass surface that is being cut by a topo plane. What I am trying to achieve or show is a height setback set from the existing topo to a height of 35'. I've tried to cutting or joining the two geometries but this will not work. There is no way to snap t the intersection of were the mass and the Topo surface meet. Is there a way to change a Topo surface into a mass? Any other way to achive this instead of massing and topo surfaces?
View 5 Replies
View Related
Aug 16, 2013
I have created a schedule based off some OFCI ( Owner Furnished Contractor Installed) Items. Some of these items cannot be found online or in the revit library (such as a spectrophotometer). So I created a mass and identified type marks for these items. However, I cannot seem to get the mass items to show on the multi-category schedule. Is there a way to do this or another way to create a schedule that includes mass and equipment?
View 1 Replies
View Related
Feb 25, 2014
Is this a Revit Hard Code issue or am I overlooking something? I have created some In-Place Masses (with floor mass for each level) and I have created 2 Project Parameters for for the Mass Schedule. Parameters are Block and Sub Block as Text under Identity Data and in the Mass Category. When the Mass Heading is ticked all mass categories are ticked. So Im thinking, it should not matter what type of Mas schedule I setup. The Parameters should be available in the fields.
The Schedule is created as a Mass Schedule. and the Parameters show up in the field and data is populated as I expect.
I want to create a Mass Floor Schedule and the parameters are not showing up in the fields list. Also I can not Add Parameters from the Schedule dialogue window as those Parameters has already been created. When I select the Mass Floor in a 3D view the Identity Data fields in the Properties window are mostly greyed out. The Project Parameters do not appear as Identity Data fields and the Edit Type is greyed out (not that Edit Type maters but it adds to the thinking process)
View 8 Replies
View Related
Dec 21, 2012
I'm now working on my diploma work and I need to model a gridshell construction in Conceptual mass.I created the form and made adaptive component -a glass panel.I uploaded it in the family and now I need to load that family into the project space and I don't know what to do..I will have to remove the mass eventually before rendering but then the gridshell structure will disappear.I don't know how to make it real,I cannot use massing and site with this, I'm obviously missing some steps and i don't know which ones..
View 1 Replies
View Related
Sep 19, 2011
I've created an irregularly shaped mass (column corbel) within a project and would like to make it a concrete object. How do I do this?
View 1 Replies
View Related
