Revit :: Calculation Of Void Volumes
Feb 5, 2013
I am working a little 'off piste' currently as I am usually designing buildings, however, I have been asked to design a mould for the casting of an additional mass of lead to be appended to the existing lead in the keel of a yacht.
In order to complete this exercise the volume of the mould must accommodate between 26 and 30 litres of lead which is the volume of lead required to give the correct weight.
I have begun this task by creating a new Revit Family (may have been better to create it in a Project Environment) essentially being a large extrusion, with a number of swept blend voids creating the mould cut out. I have determined this using my clients instructions for the type of cross sectional profile, its profile along its length and the footprint. Thing is I now have to work out what alterations are necessary in order to ensure that the mould volume is correct! See 3D View so far.
View 7 Replies
ADVERTISEMENT
Jul 24, 2013
I have a manure storage pond that I am trying to figure out the total storage volume for. It has 2.5:1 Side slopes and a 10 foot wide ramp at 10:1 entering the pond to the floor bottom. I am trying to figure out what the volume of this pond is. What is the fastest and most efficient way to get this volume? I do not want it compared to any other surface such as existing ground.
View 7 Replies
View Related
Jul 25, 2011
I am trying to create a void form in revit architecture, i am following the quick start tutorial from the design academy website and when I try to make a void form i get an error, pics to explain:
View 1 Replies
View Related
Feb 7, 2013
Can a void be converted to a solid?
View 6 Replies
View Related
Oct 26, 2013
I am trying to make a void element but whatever I do this message occurs: "Some Void Forms of this family do not cut anything and will be deleted. To make a Void Form cut something else use the Cut Geometry tool." I am using "Model in place" tool -> Generic models.
I use Revit 2014 with Service Pack 1.
View 1 Replies
View Related
Oct 6, 2013
When adding an element, say a door, to something like a wall, if there is a void within the door and everything is set properly to cut out a section of the wall, what is the resultant material colour that you see at the cut?
I've been trying this out and in the Realistic display mode, when I have a door with a recess profile around the frame, in brick I see the brick colour, but in plaster I see a grey which isn't the same as the default plaster colour?
The recess is 12mm into 12.5mm plaster.
View 1 Replies
View Related
May 29, 2012
What would be possible reason for a void not having any effect on cutting an object? I created a parametric void.Then I created an object.No change to the object. If I create an object then a void, it seems to work.
View 1 Replies
View Related
Nov 7, 2012
I am having problems with void that i cant hide in my project. The void is inside my generic family but wont apply a cut unless i apply a length parameter to it. The problem i that in my project it seems to be visible as a yellow box that will also appear when printed.
Is it possible to hide this in the project by any way?
View 1 Replies
View Related
Oct 27, 2011
I have inserted a recess paper towel dispenser into an interior wall. Then a 1/8" tile wall was added in front of the hosting interior wall. The opening for the recess dispenser only cut into the interior hosting wall, not the tile wall. I tried joining the two walls, but it didn't seems to have any effect. Is there any reason why the walls won't join?
View 4 Replies
View Related
Jan 16, 2013
I am creating a tunnel with a profile consisting of multiple radios. In the attached images can be displayed. The problem I have is that by selecting one of the two tunnels and create a void with the profile of the second tunnel and perform cutting geometry indicates that I can not and I get the error message.
If I perform the same exercise to select a tunnel and create a void with a square profile, rectangular or cylindrical deaja if I make the cut geometry. I select the void that did work and edit it to add the profile you require and at the end of the model throws me the error again.
We are working on four computers of the same features and the same version of Revit Building Design Suite 2013, has installed the update 2.
View 1 Replies
View Related
Nov 27, 2013
I have created a simple pipe fitting family, a soil vent pipe terminal infact, but I cannot get the solid body created from a rotated profile to be cut by an arrayed extrusion void. I keep getting the error message, 'Can't keep the elements joined'!
View 2 Replies
View Related
Jun 6, 2012
I need to resolve the corner condition where two boards intersect. I am not able to create a void in order to cut the corner for the geometry. I would like to shape more than one side of the board and make it rounded. How do I edit the different sides of the geometry?
See attachment for Revit model:
View 9 Replies
View Related
Jun 30, 2012
I created a reception desk in Revit 2013 using solid extrusions and void extrusions and it looks really good. The problem is I need to recreate this thing using some other method since I cannot place door and drawer faces on a plane that technically, geometrically does not exist, ie the area a receptionist would sit. The rendering of my extruded desk is attached.
View 8 Replies
View Related
Nov 28, 2011
is it possible to do a energy calculation in Revit?
View 1 Replies
View Related
Mar 11, 2013
Calculation of the double face of a wall,
I’m wondering if there is a way to calculate the area of double face of a given wall. For exam, say that we have a wall of 4x4x0.1 meter then the area of one face is 16m2 while the double face is 32m2. Does the Revit calculate the double face of a given wall?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
View 2 Replies
View Related
Apr 24, 2012
How can I calculate the landscape areas in a site plan?
Can I make a schedule to show the landscaping verse asphalt percentage?
View 5 Replies
View Related
Oct 28, 2013
How to change currency rate used for calculation of electrical and fuel prices in revit 2013 during Energy Analysis?
View 2 Replies
View Related
Sep 1, 2013
I am encountering a problem with a panoramic picture created using photomerge and 8 pictures (with photoshop cc)The result was quite good with the exception of one segment not quite properly aligned.
I managed to switch it up by a few pixels and the overall picture is almost "perfect" except that I have at one seam some empty space which I cannot fill by none of the tools like stamping, brushing, patching or even paint bucket.
Now i have a snicking suspicion that the problem lies with the layers but I cant figure out to create duplicate layers and when that can be done.
View 2 Replies
View Related
Aug 5, 2013
I have a complex part that will be created using additive manufacturing. Since this type of machining is adding material needed rather than removing material, I would like the make voids and hollow out the part wherever possible to reduce the manufacturing time, and the weight of the part. Are there any features in Inventor that allow you to click on an internal volume and specify a void that produces certain wall thickness? The closest feature I can think of is the Shell feature but that only works for parts with very simple geometry and it doesn't make a void like I would like. The shell feature cuts out material from the face so it is good for making something like a cup but does not make an internal void.
View 9 Replies
View Related
Nov 23, 2011
My Catalog "somehow" has become distributed over two volumes A and B. A has 60,000 and B has 5,000 files. How do I consolidate the volumes? [I want A to have all 65,000 images]
(Later I want the other of the volumes to simply be a bakup)
I would like to add that volumes A and B are my Master Library, each of which is subdivided into folders for years and within each year there are folders for each event. The two volumes have the same hierarchy of folders.
View 4 Replies
View Related
Jun 29, 2012
I have a question concernig a wrong result of computed volume.
EG surface with all EG points H=100.00m
FG surfase, created by FL-Square 100x100m H=101.00m, added to FG surface as breakline.
The Result-Fill=9149.59???
Why not 100x100x1=10 000???
P.S. EG points at above example were around 80, randomly spread at area say 150x150m
When I deleted 76 and moved remainig 4 at the corners of the square, the result is OK 10 000cu.m
View 1 Replies
View Related
Mar 13, 2013
I am trying to find an easy way of calculating the volumes I have been asked to do. I have a road, with an alignment created along the centreline. I have created a finished surface which incorporates the cutout for the boxing, and I have been supplied with a surface of the natural (original state) ground.
What I have been asked to do is calculate volumes at either 10m or 20m chainages (station).
Obviously, I can create a boundary, and then shift the boundary to where I want the volumes to be, but this road is 3km long, resulting in calculating 150-300 different volumes. The road is not a straight line either and includes a number of bends.
Is there a quick way of calculating this? Or do I need to use the boundary option?
The way they would normally calc it is to add all the details from the cross-sections into an excel sheet, and makesome complex formulas to figure it out. Even doing the boundary method is quicker than that.
View 1 Replies
View Related
Nov 20, 2013
We have a good size channel and the section for the channel varies quite a bit. We want to find the volume excavated in the channel between 2 elevations (it is the area of sand per the goetech report)? A template was not used to create the channel surface, breaklines and gradings were used.
View 9 Replies
View Related
Jun 7, 2012
I have sevreal corridors with various spurs. The contractor wants the cut/fill volume in sections along the corridors, not one big cut/fill calc. Is there a way to do this in C3D? I have got the volume table with the chainages on, but he does not want a cumulitive figure for the whole corridor.
View 1 Replies
View Related
Jan 31, 2013
I've had a rather odd request come in for Volume calculations and I'm not sure how to go about it.
I have 2 surfaces: 1-Design 2-Excavation to Date
Now, the engineers would like to use a dozer to push this material down the hill but they want to do it incrementally by elevation. They would like to know how much material there is to excavate above elevation 90, then between elevation 80-90, then 70-80, etc all the way to 30-40.
I attached a sketch... what is the best way to do this?
AUTOCAD Civil 3D 2013
Windows 7
Processor: Intel (R) Xeon (R) CPU W3565 @ 3.20GHz
Installed Memory (RAM): 12.0GB
System Type: 64-bit
View 2 Replies
View Related
Aug 29, 2012
I have noticed that the value I get when I use the surface volume comparison tool or look at a graded item in the grading group properties box is different than if I calculate it by hand and the discrepancy isn't even consistant. After spotting this problem in a job I am working on graded two simple ponds to check this. The first one is 100' x 100' and 5' deep w/ 2:1 side slopes. Calculating the volume by hand I get 1500 cu. yds but the grading group properties come up to 1506.17 cu. yds. The accuracy is off by less than 0.5% The second pond is 100' x 100' and 2' deep with 3:1 side slopes. The hand calc gets me 654.52 cu. yds. and the grading group properties reads 655 cu. yds. This discrepancy is closer to 7%. I really need to know if I can trust the volume tools in the program.
View 9 Replies
View Related
May 1, 2013
I am attempting to take two surfaces and cut straight down through a set polyline and get the difference between two surfaces. Do i want to use the bounded volumes to do this? Or can i simply create two surfaces and and use the analyze/volumes tool and just select the two. I would then add the boundary to each surface to limit the data.
My concern is since the two surfaces do not meet along the edges which will cause the math to be off.
View 6 Replies
View Related
Feb 23, 2012
I have a few vary large stockpile that i need to get volumes of the stockpile at 1 meter intervals- is there a quick way of doing this, other then finding the area of each elevation and calculating the volumes.
View 8 Replies
View Related
May 30, 2012
I have an existing topo surface created as well as grading for a proposed elevated pad of earth done in civil 3d 2013. I simply want to calculate the cut and fill quantities. I created the grading with automatic surface creation checked on. When I use volume tools to see what the quantities are, it says 0.0 for both cut and fill.
I created another surface (TIN) and pasted the existing topo surface and the proposed grading surface into it and I couldn't get any quantities.
I created another surface (TIN volume) and set the base surface as the existing surface and the comparison surface as the surface created from the grading but again could get no quantities.
View 1 Replies
View Related
Jun 1, 2012
I am looking to find out if the is a way of generating a stage storage table or volume table showing only the volume in the pond from the lowest intersecting existing ground contour to the top of the pond (to determine what would spill out of the pond in case of a berm failure) and if Civil 3D could make the determination of where that intersecting point is.
View 1 Replies
View Related
May 14, 2013
I have a red circle in the left hand upper corner of my photos. I position my mouse on the circle and it says OFFLINE. I go to print them and get the following message in a box: Find offline volumes. Print one or more selected item are located on removable volumes. I notice they are on volume K. I have no K volume. I only have drive C & D.
View 9 Replies
View Related
