We have a family that errors when certain values are hit. Its realated to Automatic Sketch Dimension reassociating with work planes when two workplans over lap... Anyway, the QA team knows about this.
The problem I have is that I have an IF statement to trigger an generic error message when these two rare conditions are met. I would rather a pop up window explaining what thy can not do. "Position of legs from ends can not equal half total length" and an OK button.
Is there a "say" style command for revit formulas?
New to Revit. Using 2012. I'm trying to add a double hung window to a wall and get the following error message:
Can't make type "Double Hung with Trim : 36" x 48" - Error 1 -- Windows : Double Hung with Trim : 36" x 48" - Mark 22 : id 172423 -- Type : Windows : Double Hung with Trim : 36" x 48" : id 172439
I get the same error message no matter what size I try to use
I'm facing a problem dealing with visibility formulas... My situation that im dealing with is, I have 2 yes/no visibility parameters, one that is called Right side clearance and another one named Left side clearance. I want to create another yes/no visibility parameter that's called Clearance. I want to link the Right and Left clearance parameter to the Clearance parameter where if it is off, then there will be nothing that shows.. But if I want it on then I would have to select either right or left without them both showing up?
i want to create a sketch line for a sweep where the radius of the curve varies.. i don't want to use a spline or piece together arcs.. something about distance and radius along the line.. is there a formula and can this be done in revit?
it is possible to create text and then attach a formula to it to change it.
For example:I want to be able to draw or pick a line and if the line is less than X ft than "Say this" if the line is greater than X ft than "Say that"
I wish to create a formula for a family parameter which itself references a 'Type' of an imported family. Specifically I wish to create a quoin stack which can be used for a 'reveal' situation either side of a door or window rather than just on a corner. A 'quoin stack,' as that which comes with the revit content files, typically is made up of two vertical arrays which intersect giving alternative long and short sides. Each of the arrays is made up of a different quoin type, a 'Short' and a 'Long' type which swap dimensions from from perpendicular face to the other. This of course is no good for a reveal situation where on the window or door reveal of both interleived courses needs to be the same, whilst maintaining the 'long/short' appearance on the wall face containing the window or door.
I have got so far as to create a 'reveal depth' parameter within the quoin stack family but need to find a way of addressing the 'Long' quoin type to change its 'short' dimension to suit the reveal depth whilst changing the 'long' dimension of the 'Short' quoin type to be the same.
is it possible (Revit 2014) to set up alternate dimensions that report the value represented in a different way via a simple formula?
I am trying to show my dims as brick units (based on standard metric bricks 215x102.5x65mm with 10mm mortar joint), and was hoping to create new 3 dim types, based on CO+, CO- and CO, so the alternate dims i want would be:
I am trying to change a dimension based on what yes/no parameters are checked. It keeps telling me that its "a bad if statement format". It works fine for the first teo dimension tests but when I add this last one I get the error. I need the 3rd dimension to check against 3 yes/no parameters all being = yes before moving on to the next check.
I modified a Window Family file by adding a Window inset parameter. When I inserted the window into a wall, otherwise the window worked fine, but when I changed the window's Window Inset value, the frame depth changed instead of the frame's location. The frame was originally made by Sweep tool, but now when I made it by Extrusion tool, the window works fine. Anyway, for future purposes, I would like to know how to be able to use the Window Inset parameter with a frame made by Sweep tool. How do I lock the depth of the frame sweep?
I'm using Corel videostudio X6 and I have 2 problems.
1. when i go in to track/customize motion mode, the window is bigger than the screen so i can't use this option (i'm using lap top wide screen). like in here: [URL] ....
2. when i'm adding a text to low quality video the text doesn't look well and i wonder how can i maintain the quality of the text?
I'm a relatively new user to Revit (almost a year). My issue is that all of a sudden my view control bar is located so far to the left in the view window, the project browser almost covers it. I know that I can move the project browser window so that isn't all that critical. My concern is that when I want to look at a schedule it also is so far to the left of the screen I have to move the other windows to see it.
I have several window types in my project. Let's say that the window is 3'-0" wide by 4'-8" high - Mark #1. I want to group three of these windows and schedule the group as Mark #2 - not three separate #1 windows. How do I set up the three windows together to become a single window schedulable for the entire opening of the three windows grouped together so that the opening would read 9'-0" wide?
Cannot insert any window in this wall (its 140mm blockwork single skin trimmed to the roof above) and tried different window families. Yet I can cut an opening and also insert any door.
I created this little building with a pitched roof. at the 1st level I had no problems putting in openings for windows and doors, but now i created the roof and I want to put in window at front and back of the building and the window shows only up when I hold the cursor over it. what step am i missing? At one point i also got the message "rectangular opening does not cut its host"
how to center a window seat that extends out like a bay window. I cannot for the life of me figure this out. I am trying to center the 6' extension between an exterior (7 1/4") and interior (4") wall. I need it to be center on both interior and exterior and do not know where to measure from to accomplish that.
I can't put my nested window family in a curved wall. Where the problem could be situated? It has to be a normal straight window so I use my nested window families from other projects. I compared my NWF(nested window family) with the ones autodesk provides with revit but I don't find the difference. The NWF from autodesk work in a curved wall.
I have a number of windows already in the project - of differing types.
The numbering (marks) have been assigned as I created each one.
I would now like to add a prefix to the mark in the form of:
W0/01, W0/02, W0/03 etc. for ground floor windows then: W1/01, W1/02 ... etc for first floor.
If it is not possible to break down by floor, then simply having a prefix W/01, W/02, W/03 etc. would work.
I can alter individual window types and amend the Mark to include the prefix, but it only seems to affect the one window - and not all instances of the same type.
Ideally - is it possible to set a standard prefix for use in window Marks throughout a project, regardless of type and whether it has already been inserted or in the future ?
In the file attached, there's a wall roof window joint showing the following problem: It seems like the window interferes with the joint, so that it isn't right, if the window is not situated higher than the roof slab. In the picture, the joint on the left side is correct, but the ones on the left are incorrect.
The window type showed up in the window schedule. But the window dimension didn't.
What's the reason of it? I know you can enter the dimension directly into the schedule. But it would be nice if it comes it automatically. See attached file.
I have a student version of revit 2014 and all my sizing, setting out and dimensions are coming in at feet and inches. I have found out how to convert this to mm but when I load in windows and doors, all the sizes of these are in feet and inches. How to change the door and window sizes to mm so that I know what size they are.
How do you set the view range to show a window with a sill height of 5'-0" and a dog door with a head height of 2' in the same wall on a floor plan view?
I am trying to add some storefront doors into my storefront that is already placed. The normal doors work, but I can not load in, any other door types from the "doors" family component library. It will only let me use the type that is already loaded in. It doesnt even give me an error dialogue, just the circle with the slash through it when i click on "Open" to load a door in.
